P0046 Turbocharger / Supercharger Boost Control "A" Circuit Range / Performance
Diagnostic trouble codes · Vehicles built from Jan 2017
Also covers:
- P0047 Turbo / Super Charger Boost Control Solenoid Circuit Low
- P0048 Turbo / Super Charger Boost Control Solenoid Circuit High
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
These DTCs indicate that the DC motor of the turbocharger is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.The DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the DC motor in accordance with the driving conditions.
If the nozzle vane is stuck closed (DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 5 seconds |
Either condition is met when the motor is operating (1 trip detection logic):
|
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| 2 seconds after engine is started, race engine for 1 second |
The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more (1 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| 2 seconds after engine is started, race engine for 1 second |
Overcurrent is detected 25 times or more (0.4 seconds or more) (1 trip detection logic). |
|
- HINT:
- If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck closed, the following symptom may appear:
- Vehicle surge when driving with full load
- If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck open, the following symptoms may appear:
- Lack of power
- Vehicle surge or hesitation under light or medium load
- If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck closed, the following symptom may appear:
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0046, P0047 AND/OR P0048) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Result Result
Proceed to
P0046, P0047 and/or P0048 is output
A
P0046, P0047 and/or P0048 and other DTCs are output
B
- HINT:
- If codes other than P0046, P0047 and/or P0048 are output, perform troubleshooting for those DTCs first.
|
|
||||
| A | |
| 2. INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION) |
Inspect the turbocharger sub-assembly (Click here).
|
|
||||
| OK | ||
| ||
| 3. INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE) |
Disconnect the DC motor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Always
1 to 100 Ω
Text in Illustration *a
Component without harness connected
(DC Motor)
Reconnect the DC motor connector.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM) |
Disconnect the DC motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D65-1 (M-) - D98-85 (VNM-)
Always
Below 1 Ω
D65-2 (M+) - D98-86 (VNM+)
Always
Below 1 Ω
D65-1 (M-) or D98-85 (VNM-) - Body ground
Always
10 kΩ or higher
D65-2 (M+) or D98-86 (VNM+) - Body ground
Always
10 kΩ or higher
Reconnect the DC motor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 5. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 6. REPLACE TURBOCHARGER SUB-ASSEMBLY |
Replace the turbocharger sub-assembly (Click here).
|
|
||||
| 7. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
