2014-2019 Hiace · Service Manual ENGINE

P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low

Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.
The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.
A221597E08
P2564 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VTA1 voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. ECM
P2565 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VTA1 voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. ECM

HINT:
If DTC P2564 and/or P2565 is stored due to the nozzle vane being stuck open, the following symptoms may appear:
  1. - Lack of power
  2. - Vehicle surge or hesitation under light or medium load


WIRING DIAGRAM

A221590E25

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2564 AND P2565)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P2564 and/or P2565 is output
    A
    P2564 and/or P2565 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2. CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)
  1. Disconnect the nozzle vane position sensor connector.

  1. Disconnect the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D66-1 (VTA1) - D99-116 (VNA)
    Always
    Below 1 Ω
    D66-2 (VNE2) - D99-95 (VNE2)
    Always
    Below 1 Ω
    D66-3 (VNVC) - D99-94 (VNVC)
    Always
    Below 1 Ω
    D66-1 (VTA1) or D99-116 (VNA) - Body ground
    Always
    10 kΩ or higher
    D66-3 (VNVC) or D99-94 (VNVC) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the nozzle vane position sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


3. INSPECT ECM (VNVC VOLTAGE)

  1. A200914E37
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D66-3 (VNVC) - D66-2 (VNE2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Nozzle Vane Position Sensor)



NG
Go to step 5
OK


4. REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)
  1. Replace the turbocharger sub-assembly (Click here).



NEXT
Go to step 7
5. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and leave the vehicle for 15 seconds.

  1. Turn the ignition switch to ON for 1 second.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P2564 and/or P2565.

    3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, idle the engine.


NEXT

END


← P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low (+ P2565) (Dec 2015 – Mar 2016)P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low (+ P2565) (from Jan 2017) →