INSPECTION
Inspection · Vehicles built from Oct 2014
| INSPECT CAMSHAFT |
Inspect the circle runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout.
- Maximum circle runout:
- 0.03 mm (0.0012 in.)
Inspect the cam lobe height.
Using a micrometer, measure the cam lobe height.
- Standard Cam Lobe Height:
Item
Specified Condition
w/ DPF
46.991 to 47.091 mm (1.8500 to 1.8540 in.)
w/o DPF
47.180 to 47.280 mm (1.8575 to 1.8614 in.)
- Minimum Cam Lobe Height:
Item
Specified Condition
w/ DPF
46.571 mm (1.8335 in.)
w/o DPF
46.760 mm (1.8409 in.)
Inspect the journal diameter of the camshaft.
Using a micrometer, measure the journal diameter of the camshaft bearing.
- Standard journal diameter:
- 27.969 to 27.985 mm (1.1011 to 1.1018 in.)
Check the oil clearance.
Clean the bearing caps and journals.
Check the bearings for flaking and scoring.
If the bearings are damaged, replace the bearing caps and cylinder head as a set.Install the bearings to the bearing caps and cylinder head.
Place the camshaft on the cylinder head.
Lay a strip of Plastigage across each of the journals.

Text in Illustration *1
Plastigage
Install the bearing caps.
- NOTICE:
- Do not turn the camshaft.
Remove the bearing caps.
Measure the Plastigage at its widest point.

- Standard oil clearance:
- 0.025 to 0.062 mm (0.0010 to 0.0024 in.)
- Maximum oil clearance:
- 0.10 mm (0.0039 in.)
If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the bearing caps and cylinder head as a set.Text in Illustration *1
Plastigage
Completely remove the Plastigage.
Remove the camshaft (Click here).
Check the thrust clearance.
Install the camshaft (Click here).
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

- Standard thrust clearance:
- 0.035 to 0.185 mm (0.0014 to 0.0073 in.)
- Maximum thrust clearance:
- 0.25 mm (0.0098 in.)
Using a dial indicator, measure the backlash.
Install the 2 camshafts.
Using a dial indicator, measure the backlash.

- Standard backlash:
- 0.035 to 0.089 mm (0.0014 to 0.0035 in.)
- Maximum backlash:
- 0.189 mm (0.0074 in.)
Remove the 2 camshafts (Click here).
| INSPECT NO. 2 CAMSHAFT |
Inspect the circle runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout.
- Maximum circle runout:
- 0.03 mm (0.0012 in.)
Inspect the cam lobe height.
Using a micrometer, measure the cam lobe height.
- Standard Cam Lobe Height:
Item
Specified Condition
w/ DPF
48.305 to 48.405 mm (1.9018 to 1.90570 in.)
w/o DPF
48.070 to 48.170 mm (1.8925 to 1.8965 in.)
- Minimum Cam Lobe Height:
Item
Specified Condition
w/ DPF
48.155 mm (1.8959 in.)
w/o DPF
47.920 mm (1.8866 in.)
Inspect the journal diameter of the camshaft.
Using a micrometer, measure the journal diameter of the camshaft bearing.
- Standard journal diameter:
- 27.969 to 27.985 mm (1.1011 to 1.1018 in.)
Check the oil clearance.
Clean the bearing caps and journals.
Check the bearings for flaking and scoring.
If the bearings are damaged, replace the bearing caps and cylinder head as a set.Install the bearings to the bearing caps and cylinder head.
Place the camshaft on the cylinder head.
Lay a strip of Plastigage across each of the journals.

Text in Illustration *1
Plastigage
Install the bearing caps.
- NOTICE:
- Do not turn the camshaft.
Remove the bearing caps.
Measure the Plastigage at its widest point.

- Standard oil clearance:
- 0.025 to 0.062 mm (0.0010 to 0.0024 in.)
- Maximum oil clearance:
- 0.10 mm (0.0039 in.)
If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the bearing caps and cylinder head as a set.Text in Illustration *1
Plastigage
Completely remove the Plastigage.
Remove the camshaft (Click here).
Check the thrust clearance.
Install the camshaft (Click here).
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

- Standard thrust clearance:
- 0.035 to 0.185 mm (0.0014 to 0.0073 in.)
- Maximum thrust clearance:
- 0.25 mm (0.0098 in.)
Remove the camshaft (Click here).
