2014-2019 Hiace · Service Manual COMMUNICATION SYSTEM

B2789 No Response from ID BOX

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015

DESCRIPTION

This DTC is output when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.
DTC Code
DTC Detection Condition
Trouble Area
B2789
No communication between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) for 10 seconds or more
  1. Certification ECU (smart key ECU assembly)
  2. ID code box (immobiliser code ECU)
  3. Harness or connector

WIRING DIAGRAM

B301232E05

INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) (Click here).

HINT:
DTC B2785 is output when the communication between all of the following components and certification ECU (smart key ECU assembly) stops.


1. CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2789 is output
    A
    DTC B2789 is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ID CODE BOX [IMMOBILISER CODE ECU])
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the H81 ID code box (immobiliser code ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-5 (LIN) - H81-2 (LIN1)
    Always
    Below 1 Ω
    B75-5 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILIZER CODE ECU] - BATTERY AND BODY GROUND)
B301231E02
  1. Disconnect the ID code box (immobiliser code ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H81-5 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H81-1 (+B) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to ID Code Box [Immobilizer Code ECU])


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Temporarily replace the certification ECU (smart key ECU assembly) with a new one.


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2789 is not output.



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] IS DEFECTIVE)


← B2786 No Response from Steering Lock ECU (from Jan 2015)B2789 No Response from ID BOX (from Jan 2015) →