2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Oct 2014

NOTICE:
  1. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  2. After removing the fuel inlet pipe, clean it with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE TIMING BELT
(Click here)

3. REMOVE EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY (w/ DPF)
(Click here)

4. REMOVE EGR COOLER ASSEMBLY (w/o DPF)
(Click here)

5. REMOVE VANE PUMP ASSEMBLY
(Click here)

6. REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. A239512E01
    Disconnect the 3 fuel hoses.

  1. Remove the bolt and No. 2 injection pipe clamp from the No. 3 nozzle leakage pipe and No. 3 fuel pipe.

  1. Remove the fuel check valve and gasket.

  1. Remove the bolt and No. 3 nozzle leakage pipe.


7. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)

  1. A233147
    Remove the 2 bolts and No. 2 exhaust manifold heat insulator.


8. REMOVE NO. 3 FUEL PIPE (w/ DPF)

HINT:
It is not necessary to completely remove the No. 3 fuel pipe from the vehicle.

  1. for Engine LH Side:

    1. Using a 6 mm hexagon wrench, remove the union bolt and gasket.

    2. Remove the fuel check valve and gasket.

    3. Remove the bolt.

  1. for Engine Rear Side:

    1. Remove the union bolt and gasket.

    2. Remove the 2 bolts.

      A239513E01


9. REMOVE FUEL INLET PIPE SUB-ASSEMBLY (w/o DPF)

  1. A177108E01
    Remove the bolt and No. 2 injection pipe clamp.

  1. Remove the bolt and detach the No. 1 injection pipe clamp.

    NOTICE:
    If a No. 1 injection pipe clamp is removed from the fuel inlet pipe, replace the No. 1 injection pipe clamp with a new one.

  1. A177109
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.


10. REMOVE FUEL SUPPLY PUMP ASSEMBLY
  1. w/ DPF:
    Disconnect the fuel hose.

  1. w/o DPF:
    Disconnect the 2 fuel hoses.

  1. Disconnect the fuel temperature sensor connector and suction control valve connector.

  1. A070710E01
    Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.

  1. A070711E04
    Remove the set nut and O-ring while holding the crankshaft pulley with SST.
    SST
    09213-58014  
    09330-00021  

  1. A148291
    Loosen the 2 nuts.

  1. A070714E02
    Using SST, disconnect the fuel supply pump from the injection gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and fuel supply pump.

    NOTICE:
    1. Do not hold or carry the fuel supply pump by the pipe.
    2. The fuel supply pump must be kept horizontal.

  1. Remove the O-ring.

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →