B279A Theft Deterrent System Communication Line High Fixation
Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
When the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high, the ECM stores this DTC.| DTC Code |
DTC Detection Condition |
Trouble Area |
DTC Output Confirmation Operation |
| B279A |
The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high (1 trip detection logic*1). |
|
Turn the engine switch on (IG) and wait 6 seconds. |
- *1: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected |
Fail-safe Operation when Malfunction Detected |
| Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) |
Engine cannot be started |
| DTC Code |
Data List and Active Test |
| B279A |
- |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- Before replacing the ID code box (immobiliser code ECU), refer to Service Bulletin.
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."
- When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- HINT:
- When DTC B279A and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Turn the engine switch on (IG) and wait 10 seconds.
Check for DTCs (Click here).
Result Result
Proceed to
DTC B279A is output
A
DTC B279A and other DTCs are output
B
- HINT:
- If DTCs other than DTC B279A are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 3. CHECK CONNECTION OF CONNECTOR |
Turn the engine switch off.
Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).
- OK:
- Connectors are properly connected.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - ECM) |
Disconnect the H81 ID code box (immobiliser code ECU) connector.
Disconnect the B72 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H81-4 (EFIO) - B72-16 (IMI)
Always
Below 1 Ω
B72-16 (IMI) - Body ground
Always
10 kΩ or higher
H81-4 (EFIO) - Body ground
Always
10 kΩ or higher
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B72-16 (IMI) - Body ground
Always
Below 1 V
|
|
||||
| OK | |
| 5. REPLACE ID CODE BOX (IMMOBILISER CODE ECU) |
Replace the ID code box (immobiliser code ECU) with a new one.
- HINT:
- Refer to the Service Bulletin.
| NEXT | |
| 6. REGISTER RECOGNITION CODES |
Register the recognition codes in the ECUs.
- HINT:
- Refer to the Service Bulletin.
| NEXT | |
| 7. REGISTER ECU COMMUNICATION ID |
Register the ECU communication ID.
- HINT:
- Refer to the Service Bulletin.
| NEXT | |
| 8. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 9. CHECK FOR DTC |
Check for DTCs (Click here).
- HINT:
- Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
- OK:
- DTC B279A is not output.
|
|
||||
| OK | ||
| ||
