2014-2019 Hiace · Service Manual ENGINE

Injector Circuit

Circuit diagnosis · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

WIRING DIAGRAM

Refer to DTC P0201 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  4. After replacing an injector assembly, the ECM needs registration (Click here).


1. CHECK INJECTOR DRIVER (POWER SOURCE)

  1. A204910E19
    Disconnect the injector driver connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B60-2 (+B) - B60-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Injector Driver)

  1. Reconnect the injector driver connectors.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT NO. 1 INTEGRATION RELAY (EDU RELAY)
  1. Inspect the No. 1 integration relay (EDU relay) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY (EDU RELAY)
OK


3. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - NO. 1 INTEGRATION RELAY)
  1. Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.

  1. Disconnect the injector driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B60-2 (+B) - 10A-8
    Always
    Below 1 Ω
    B60-4 (GND) - Body ground
    Always
    Below 1 Ω
    10A-6 - 10B-4
    Always
    Below 1 Ω
    B60-2 (+B) or 10A-8 - Body ground
    Always
    10 kΩ or higher
    10A-6 or 10B-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the injector driver connector.

  1. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)
  1. Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B73-44 (IREL) - 10A-7
    Always
    Below 1 Ω
    B73-44 (IREL) or 10A-7 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← Injector Circuit (Dec 2015 – Mar 2016)Injector Circuit (from Jan 2017) →