2014-2019 Hiace · Service Manual ENGINE

Starter Signal Circuit

Circuit diagnosis · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

for A/T:
While the engine is being cranked, current flows from terminal ST1 of the ignition switch to the park/neutral position switch and to terminal STA of the ECM (STA Signal).
for M/T:
While the engine is being cranked, current flows from terminal ST1 of the ignition switch directly to terminal STA of the ECM (STA signal).

WIRING DIAGRAM

Refer to DTC P0617 (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
This inspection procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table (Click here).


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value.

    OK:
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON

    Result 
    Result
    Proceed to
    OK
    A
    NG (for A/T)
    B
    NG (for M/T)
    C



B
Go to step 2

C
Go to step 5
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click here).



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM, IGNITION SWITCH)
  1. Disconnect the ignition switch connector.

  1. Disconnect the ECM connector.

  1. Disconnect the park/neutral position switch connector.

  1. Remove the starter (ST) relay from the instrument panel relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H25-1 (ST1) - D37-4
    Always
    Below 1 Ω
    B71-48 (STA) - D37-5
    Always
    Below 1 Ω
    H25-1 (ST1) or D37-4 - Body ground
    Always
    10 kΩ or higher
    B71-48 (STA) or D37-5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT IGNITION SWITCH
  1. Inspect the ignition switch (Click here).



NG
REPLACE IGNITION SWITCH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH)

5. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
  1. Disconnect the ignition switch connector.

  1. Disconnect the ECM connector.

  1. Remove the starter (ST) relay from the instrument panel relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H25-1 (ST1) - B71-48 (STA)
    Always
    Below 1 Ω
    H25-1 (ST1) or B71-48 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT IGNITION SWITCH
  1. Inspect the ignition switch (Click here).



NG
REPLACE IGNITION SWITCH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH)


← Starter Signal Circuit (Jan 2015 – Dec 2016)Brake Override System (Oct 2014 – Dec 2014) →