2014-2019 Hiace · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built Oct 2014 – Dec 2014


1. BEARING POSITION

C243437E01

Bearing and Race Diameter:
Position
Front Race Diameter Inside/Outside
Thrust Bearing Diameter Inside/Outside
Rear Race Diameter Inside/Outside
A
-
24.32 mm (0.957 in.)/43.20 mm (1.70 in.)
24.32 mm (0.957 in.)/39.20 mm (1.54 in.)
B
-
37.30 mm (1.47 in.)/52.52 mm (2.07 in.)
-
C
30.00 mm (1.18 in.)/48.54 mm (1.91 in.)
28.30 mm (1.11 in.)/46.48 mm (1.83 in.)
27.58 mm (1.09 in.)/44.70 mm (1.76 in.)
D
24.05 mm (0.947 in.)/37.59 mm (1.48 in.)
23.34 mm (0.919 in.)/37.59 mm (1.48 in.)
-
E
24.05 mm (0.947 in.)/37.59 mm (1.48 in.)
23.34 mm (0.919 in.)/37.59 mm (1.48 in.)
21.41 mm (0.843 in.)/37.59 mm (1.48 in.)
F
30.00 mm (1.18 in.)/47.9 mm (1.89 in.)
28.30 mm (1.11 in.)/46.48 mm (1.83 in.)
27.58 mm (1.09 in.)/44.70 mm (1.76 in.)
G
-
21.40 mm (0.843 in.)/47.30 mm (1.86 in.)
-
H
30.00 mm (1.18 in.)/48.54 mm (1.91 in.)
28.30 mm (1.11 in.)/46.48 mm (1.83 in.)
-
I
-
38.15 mm (1.50 in.)/55.30 mm (2.18 in.)
39.12 mm (1.54 in.)/57.53 mm (2.26 in.)


2. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

C191162E02
  1. Using SST, tap in 2 new manual valve lever shaft oil seals.

    SST
    09350-20015   (09361-30011)

  1. Coat the lips of the manual valve lever shaft oil seals with MP grease.


3. INSTALL MANUAL VALVE LEVER SHAFT

  1. C191163E04
    Install a new spacer to the manual valve lever.
    Text in Illustration 
    *1
    Manual Valve Lever Shaft
    *2
    Manual Valve Lever
    *3
    Spacer

  1. Insert the manual valve lever shaft into the transmission case through the manual valve lever to install it.

  1. C191164
    Using a hammer, tap in a new spring pin.

  1. C191165
    Align the manual valve lever indentation with the spacer hole, and stake them with a pin punch.

  1. Check that the manual valve lever shaft rotates smoothly.


4. INSTALL NO. 3 BRAKE PISTON

  1. C191166E04
    Coat 5 new O-rings with ATF and install them to the inner piston, brake reaction sleeve and No. 3 brake piston.
    Text in Illustration 
    *1
    No. 3 Brake Piston
    *2
    Brake Reaction Sleeve
    *3
    Inner Piston

    NOTICE:
    The thinner O-ring must be installed to the outside of the sleeve.

  1. Assemble the inner piston, brake reaction sleeve and No. 3 brake piston.

  1. C191167
    Press the assembled pistons into the transmission case by hand to install them.

    NOTICE:
    Be careful not to damage the O-rings.

  1. Make sure that the end gap of the snap ring is not aligned with the claw of the spring seat.


5. INSTALL NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C191143
    Place the No. 3 brake piston return spring sub-assembly onto the No. 3 brake piston.

  1. C191168E04
    Position SST as shown in the illustration and compress the No. 3 brake piston return spring sub-assembly with SST.
    SST
    09350-20015   (09369-20040)
    Text in Illustration 
    *a
    Claw

  1. Install the snap ring with a snap ring expander.

    NOTICE:
    1. Make sure that the end gap of the snap ring is not aligned with the claw of the spring seat.
    2. Do not expand the snap ring ends excessively.
    3. Make sure that the snap ring is inserted into the groove.


6. INSPECT NO. 3 BRAKE PISTON MOVEMENT

C191141
  1. Check that the No. 3 brake pistons move smoothly when applying compressed air into and releasing compressed air from the transmission case.


7. INSTALL BRAKE APPLY TUBE

C191139
  1. Coat the race with MP grease and install it to the transmission case.

    Race Diameter:
    Item
    Inside
    Outside
    Race I
    39.12 mm (1.54 in.)
    57.53 mm (2.26 in.)

    NOTICE:
    Make sure the race is installed so that it is oriented correctly.

  1. C191138
    Align the locking tabs of the brake apply tube with the cutouts of the transmission case and install the brake apply tube.

    NOTICE:
    Make sure that the tabs of the brake apply tube end are completely inserted into the No. 3 brake piston.


8. INSTALL BRAKE PLATE STOPPER SPRING

C191140

9. INSTALL REAR PLANETARY RING GEAR SUB-ASSEMBLY

  1. C191427
    Coat a new oil seal ring with ATF and install it to the intermediate shaft sub-assembly.

    HINT:
    After installing the oil seal ring, check that it rotates smoothly.

  1. C191429
    Coat the bearing with MP grease and install it to the intermediate shaft.

    Bearing Diameter:
    Item
    Inside
    Outside
    Bearing G
    21.40 mm (0.843 in.)
    47.30 mm (1.86 in.)

    NOTICE:
    Make sure the bearing is installed so that it is oriented correctly.

  1. C191430
    Install the ring gear to the intermediate shaft sub-assembly.

  1. C191424
    Install the set ring.


10. INSTALL REAR PLANETARY SUN GEAR

C191423

11. INSTALL REAR PLANETARY GEAR ASSEMBLY

C191421

12. INSTALL INTERMEDIATE SHAFT SUB-ASSEMBLY WITH REAR PLANETARY GEAR ASSEMBLY AND REAR PLANETARY RING GEAR SUB-ASSEMBLY

  1. C191431E02
    Coat the bearing and race with MP grease and install them to the rear planetary ring gear sub-assembly.

    Bearing and Race Diameter:
    Item
    Inside
    Outside
    Race H
    30.00 mm (1.18 in.)
    48.54 mm (1.91 in.)
    Bearing H
    28.30 mm (1.11 in.)
    46.48 mm (1.83 in.)

    Text in Illustration 
    *1
    Bearing H
    *2
    Race H

    NOTICE:
    Make sure the bearing and race are installed so that they are oriented correctly.

  1. C191418
    Install the intermediate shaft sub-assembly with rear planetary gear assembly and rear planetary ring gear sub-assembly to the output shaft assembly.


13. INSTALL FRONT PLANETARY RING GEAR

  1. C191417
    Install the snap ring.

    NOTICE:
    1. Do not expand the snap ring ends excessively.
    2. Make sure that the snap ring is inserted into the groove.

  1. C191416
    Align the snap ring ends with the wide cutout portion of the output shaft assembly.

    NOTICE:
    Make sure that the snap ring is inserted into the groove.

  1. Using a snap ring expander, install the front planetary ring gear while compressing the snap ring.

  1. Check that the snap ring is installed to the groove of the output shaft assembly.


14. INSTALL REAR PLANETARY GEAR ASSEMBLY WITH INTERMEDIATE SHAFT SUB-ASSEMBLY

  1. C191415
    Coat the thrust washer with MP grease and install the thrust washer to the rear planetary gear assembly.

    NOTICE:
    Make sure that the tabs of the washer are aligned with the cutout portions on the rear planetary gear assembly.

  1. C191137
    Coat the bearing with MP grease and install it to the output shaft assembly.

    Bearing Diameter:
    Item
    Inside
    Outside
    Bearing I
    38.15 mm (1.50 in.)
    55.30 mm (2.18 in.)

    NOTICE:
    Make sure the bearing is installed so that it is oriented correctly.

  1. C191415
    Coat the thrust washer with MP grease and install the thrust washer to the rear planetary gear assembly.

    NOTICE:
    Make sure that the tabs of the thrust washer are aligned with the cutout portions on the rear planetary gear assembly.

  1. C191428E04
    Coat a new oil seal ring with ATF.

  1. Connect the ends of the oil seal ring and install it to the output shaft assembly.

    NOTICE:
    Do not expand the oil seal ring excessively.

    HINT:
    After installing the oil seal ring, check that it rotates smoothly.

  1. C191136
    Install the intermediate shaft sub-assembly with rear planetary gear assembly and output shaft assembly to the transmission case.


15. INSTALL NO. 3 BRAKE DISC SET

  1. C191169E04
    Install the pressure plate with the flat surface facing the front of the transmission case.
    Text in Illustration 
    *1
    Pressure Plate
    *2
    No. 3 Brake Disc
    *3
    Plate

  1. Install the 5 No. 3 brake discs and 4 plates.

    Install in order:
    *1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2


16. INSPECT PACK CLEARANCE OF NO. 3 BRAKE

  1. C191133
    Using a vernier caliper, measure the clearance between the No. 3 brake disc and transmission case as shown in the illustration.

    Standard pack clearance:
    0.52 to 1.27 mm (0.0205 to 0.0499 in.)

    HINT:
    1. If the result is not as specified, replace the pressure plate with one of a different thickness.
    2. There are 6 types of pressure plates that can be used to adjust the pack clearance. Select the one with the most appropriate thickness.

    Pressure Plate Thickness:
    Part No.
    Mark
    Thickness
    35639-22010
    -
    2.95 to 3.05 mm (0.117 to 0.120 in.)
    35639-22020
    325
    3.20 to 3.30 mm (0.126 to 0.129 in.)
    35639-22030
    350
    3.45 to 3.55 mm (0.136 to 0.139 in.)
    35639-22040
    375
    3.70 to 3.80 mm (0.146 to 0.149 in.)
    35639-22050
    400
    3.95 to 4.05 mm (0.156 to 0.159 in.)
    35639-22060
    425
    4.20 to 4.30 mm (0.166 to 0.169 in.)


17. INSTALL NO. 2 ONE-WAY CLUTCH

  1. C191413
    Coat the thrust washer with MP grease and install the thrust washer to the front planetary gear sub-assembly.

    NOTICE:
    Make sure that the tabs of the thrust washer are aligned with the cutout portions on the front planetary gear sub-assembly.

  1. C191414E04
    Install the No. 2 one-way clutch and 2 retainers to the front planetary gear sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    One-way Clutch Retainer
    *2
    No. 2 One-way Clutch
    *a
    Open End

    HINT:
    Make sure that the open end of the No. 2 one-way clutch is facing upward.

  1. C191409
    Using a screwdriver, install the snap ring.

    NOTICE:
    1. Be careful not to damage the No. 2 one-way clutch and front planetary gear sub-assembly.
    2. Make sure that the snap ring is inserted into the groove.

    HINT:
    Tape the screwdriver tip before use.


18. INSPECT NO. 2 ONE-WAY CLUTCH

  1. C191407
    Hold the No. 2 one-way clutch inner race sub-assembly and turn the front planetary gear sub-assembly. Check that the front planetary gear sub-assembly can be turned counterclockwise but cannot be turned clockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free


19. INSTALL FRONT PLANETARY GEAR ASSEMBLY

  1. C191406
    Coat the thrust washer with MP grease and install the thrust washer to the front planetary gear sub-assembly.

    NOTICE:
    Make sure that the tabs of the thrust washer are aligned with the holes on the front planetary gear sub-assembly.

  1. C191170
    Install the front planetary gear sub-assembly.

    HINT:
    Mesh the splines of the front planetary gear sub-assembly with the teeth of the No. 3 brake disc set by rotating and pushing the front planetary gear sub-assembly.

  1. C191171
    Position the notched tooth of the No. 2 one-way clutch inner race sub-assembly toward the transmission valve body assembly side of the transmission case and push the No. 2 one-way clutch inner race sub-assembly into place.

    HINT:
    The No. 2 one-way clutch inner race sub-assembly is correctly installed if the snap ring groove is fully visible.

  1. C191172
    Using a screwdriver, install the snap ring.

    NOTICE:
    1. Be careful not to damage the transmission case.
    2. Make sure that the snap ring is inserted into the groove.

    HINT:
    Tape the screwdriver tip before use.


20. INSTALL NO. 1 ONE-WAY CLUTCH ASSEMBLY
  1. Coat 2 new oil seal rings with ATF.

  1. C191439E04
    Connect the ends of the oil seal rings and install the oil seal rings to the planetary sun gear sub-assembly.

    NOTICE:
    Do not expand the oil seal rings excessively.

    HINT:
    After installing the oil seal rings, check that they rotate smoothly.

  1. C191441E04
    Install the No. 1 one-way clutch to the outer race with the open end of the No. 1 one-way clutch facing rearward.
    Text in Illustration 
    *1
    One-way Clutch Retainer
    *2
    No. 1 One-way Clutch
    *a
    Open End

  1. Install the 2 one-way clutch retainers.

  1. C191442
    Install 2 new retainers to the outer race.

  1. Using a pin punch and hammer, stake the claws of the 2 retainers.

  1. C191435
    Install the No. 1 one-way clutch to the planetary sun gear sub-assembly.


21. INSPECT NO. 1 ONE-WAY CLUTCH ASSEMBLY

  1. C191434
    Hold the No. 1 one-way clutch and turn the planetary sun gear sub-assembly. Check that the planetary sun gear sub-assembly can be turned counterclockwise but cannot be turned clockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free


22. INSTALL NO. 2 BRAKE PISTON
  1. Coat a new O-ring with ATF and install it to the center support sub-assembly.

  1. Coat a new O-ring with ATF and install it to the brake piston.

  1. Install the No. 2 brake piston.

  1. C191403E01
    Place SST on the No. 2 brake piston.
    SST
    09350-20015   (09369-20040)

  1. Press the No. 2 brake piston into the center support sub-assembly by hand.

    NOTICE:
    Be careful not to damage the O-rings.


23. INSTALL NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C191400
    Place the No. 2 brake piston return spring sub-assembly onto the No. 2 brake piston.

  1. C191404E04
    Place SST on the No. 2 brake piston return spring sub-assembly and compress the No. 2 brake piston return spring sub-assembly with press.
    SST
    09350-20015   (09369-20040)
    Text in Illustration 
    *a
    Claw

  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)

    NOTICE:
    1. Make sure the end gap of the snap ring is not aligned with the spring seat claw.
    2. Do not expand the snap ring ends excessively.
    3. Make sure that the snap ring is inserted into the groove.


24. INSTALL NO. 2 BRAKE DISC SET

  1. C191397E02
    Install the 3 plates and 3 No. 2 brake discs to the center support sub-assembly.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2

    Text in Illustration 
    *1
    Plate
    *2
    No. 2 Brake Disc

  1. C191405
    Install the flange with the flat end facing downward.

  1. C191395
    Using a screwdriver, install the snap ring.

    NOTICE:
    1. Be careful not to damage the center support sub-assembly.
    2. Make sure the end gap of the snap ring is not aligned with the cutout portion of the center support sub-assembly.
    3. Make sure that the snap ring is inserted into the groove.

    HINT:
    Tape the screwdriver tip before use.


25. INSPECT PISTON STROKE OF NO. 2 BRAKE PISTON

C191394
  1. Using a dial indicator, measure the No. 2 brake piston stroke by applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) as shown in the illustration.

    Standard piston stroke:
    0.98 to 1.71 mm (0.0386 to 0.0673 in.)

    If the stroke is not as specified, inspect the No. 2 brake discs.


26. INSTALL NO. 1 BRAKE PISTON

  1. C243157
    Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.

  1. Install the No. 1 brake piston to the center support sub-assembly.

  1. C191391E02
    Place SST on the No. 1 brake piston.
    SST
    09350-20015   (09369-20040)

  1. Press the No. 1 brake piston into the center support sub-assembly by hand.

    NOTICE:
    Be careful not to damage the O-rings.


27. INSTALL NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C191386
    Place the No. 1 brake piston return spring sub-assembly onto the No. 1 brake piston.

  1. C191392E04
    Place SST on the No. 1 brake piston return spring sub-assembly and compress the No. 1 brake piston return spring sub-assembly with a press.
    SST
    09350-20015   (09369-20040)
    Text in Illustration 
    *a
    Claw

  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)

    NOTICE:
    1. Make sure the end gap of the snap ring is not aligned with the spring seat claw.
    2. Do not expand the snap ring ends excessively.
    3. Make sure that the snap ring is inserted into the groove.


28. INSTALL NO. 1 BRAKE DISC SET

  1. C191383E02
    Install the 3 plates and 2 No. 1 brake discs to the center support sub-assembly.

    Install in order:
    *1 - *2 - *1 - *1 - *2

    Text in Illustration 
    *1
    Plate
    *2
    No. 1 Brake Disc

  1. C191393
    Install the flange with the rounded edge facing upward.

  1. C191381
    Using a screwdriver, install the snap ring.

    NOTICE:
    1. Be careful not to damage the center support sub-assembly.
    2. Make sure the end gap of the snap ring is not aligned with the cutout portion of the center support sub-assembly.
    3. Make sure that the snap ring is inserted into the groove.

    HINT:
    Tape the screwdriver tip before use.


29. INSPECT PISTON STROKE OF NO. 1 BRAKE PISTON

  1. C191380
    Using a dial indicator, measure the No. 1 brake piston stroke by applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) as shown in the illustration.

    Standard piston stroke:
    0.75 to 1.35 mm (0.0296 to 0.0531 in.)

    If the stroke is not as specified, inspect the No. 1 brake discs.


30. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY WITH NO. 1 ONE-WAY CLUTCH

  1. C191433
    While turning the No. 1 one-way clutch, install the planetary sun gear sub-assembly with No. 1 one-way clutch.

  1. C191432
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07070)

    NOTICE:
    1. Do not expand the snap ring ends excessively.
    2. Make sure that the snap ring is inserted into the groove.


31. INSTALL REAR CLUTCH PISTON

  1. C191376E02
    Coat 4 new O-rings with ATF and install them to the rear clutch piston and rear No. 2 clutch piston.
    Text in Illustration 
    *1
    O-ring
    *2
    Rear No. 2 Clutch Piston
    *3
    Rear Clutch Piston

  1. Install the rear clutch piston to the rear clutch drum.

  1. Install the rear No. 2 clutch piston to the rear clutch drum.

  1. C191377E01
    Place SST on the rear No. 2 clutch piston.
    SST
    09350-20015   (09369-20040)

  1. Press the rear No. 2 clutch piston into the rear clutch drum by hand.

    NOTICE:
    Be careful not to damage the O-rings.


32. INSTALL REAR CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. C191372
    Place the rear clutch return spring sub-assembly onto the rear clutch piston.

  1. C191378E04
    Place SST on the rear clutch return spring sub-assembly and compress the rear clutch return spring sub-assembly with a press.
    SST
    09350-20015   (09369-20040)
    09350-30020   (09350-07070)
    Text in Illustration 
    *a
    Claw

  1. Install the snap ring with a snap ring expander.

    NOTICE:
    1. Make sure the end gap of the snap ring is not aligned with the spring seat claw.
    2. Do not expand the snap ring ends excessively.
    3. Make sure that the snap ring is inserted into the groove.


33. INSTALL REAR CLUTCH DISC SET

  1. C191369E02
    Install the 3 plates and 3 rear clutch discs.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2

    Text in Illustration 
    *1
    Plate
    *2
    Rear Clutch Disc

  1. C191379
    Install the flange with the flat side facing downward.

  1. C191367
    Using a screwdriver, install the snap ring.

    NOTICE:
    1. Be careful not to damage the rear clutch drum.
    2. Make sure the end gap of the snap ring is not aligned with the cutout portion of the rear clutch drum.
    3. Make sure that the snap ring is inserted into the groove.

    HINT:
    Tape the screwdriver tip before use.


34. INSPECT PISTON STROKE OF REAR CLUTCH PISTON

C191365
  1. Place the rear clutch drum onto the center support sub-assembly.

  1. C191366
    Using a dial indicator, measure the rear clutch piston stroke by applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) as shown in the illustration.

    Standard piston stroke:
    0.90 to 1.30 mm (0.0355 to 0.0511 in.)

    If the piston stroke is not as specified, parts may have been assembled incorrectly. Check the parts and reassemble again.

    HINT:
    1. If the piston stroke is still not as specified, replace the flange with one of a different thickness.
    2. There are 3 types of flanges that can be used to adjust the pack clearance. Select the one with the most appropriate thickness.

      Flange Thickness:
      Part No.
      Mark
      Thickness
      35675-22120
      A
      3.475 to 3.600 mm (0.137 to 0.141 in.)
      35675-22130
      B
      3.675 to 3.800 mm (0.145 to 0.149 in.)
      35675-22140
      -
      3.925 to 4.050 mm (0.155 to 0.159 in.)


35. INSTALL CENTER SUPPORT SUB-ASSEMBLY
  1. Coat 3 new oil seal rings with ATF.

  1. C191389E02
    Connect the ends of the oil seal rings and install the oil seal rings to the center support sub-assembly.

    NOTICE:
    Do not expand the oil seal rings excessively.

    HINT:
    After installing the oil seal rings, check that they rotate smoothly.

  1. C191173
    Position the center support sub-assembly so that the bolt holes and oil holes are facing the transmission valve body assembly and are aligned with the bolt holes and oil holes of the transmission case, and then install the center support sub-assembly.

  1. Install the 2 washers to the 2 bolts.

  1. Temporarily install the 2 bolts together with the washers.

  1. C191174E01
    Tighten the 2 bolts in the order shown in the illustration.

    Torque:
    25 N*m{ 260 kgf*cm , 19 ft.*lbf }


36. INSTALL REAR CLUTCH DRUM

  1. C191292E02
    Install the rear clutch drum.
    Text in Illustration 
    *1
    Rear Clutch Drum
    *2
    Rear Race F

    HINT:
    1. Mesh the splines of the rear clutch drum with the teeth of the No. 1 brake discs by rotating and pushing the rear clutch drum.
    2. If the rear clutch drum is fully meshed with the No. 1 brake discs, the center of the rear clutch drum splines will be flush with the end of the planetary sun gear sub-assembly.

  1. Coat the race with MP grease and install it to the rear clutch drum.

    Race Diameter:
    Item
    Inside
    Outside
    Rear Race F
    27.58 mm (1.09 in.)
    44.70 mm (1.76 in.)

    NOTICE:
    Make sure the race is installed so that it is oriented correctly.


37. INSTALL FRONT CLUTCH PISTON

  1. C191358
    Coat 2 new O-rings with ATF and install them to the front clutch piston.

  1. Place the front clutch drum onto the overdrive case sub-assembly.

  1. Install the front clutch piston to the front clutch drum.

  1. C191359E01
    Place SST on the front clutch piston.
    SST
    09350-20015   (09369-20040)

  1. Press the front clutch piston into the front clutch drum by hand.

    NOTICE:
    Be careful not to damage the O-rings.


38. INSTALL FRONT CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. C191354
    Place the front clutch return spring sub-assembly onto the front clutch piston.

  1. C191360E03
    Place SST on the front clutch return spring sub-assembly and compress the front clutch return spring sub-assembly with a press.
    SST
    09350-20015   (09369-20040)
    09350-30020   (09350-07070)
    Text in Illustration 
    *a
    Claw

  1. Using a snap ring expander, install the snap ring.

    NOTICE:
    1. Make sure the end gap of the snap ring is not aligned with the spring seat claw.
    2. Do not expand the snap ring ends excessively.
    3. Make sure that the snap ring is inserted into the groove.


39. INSTALL FRONT CLUTCH DISC SET

  1. C191351E02
    Install the 4 plates and 3 front clutch discs.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2 - *1

    Text in Illustration 
    *1
    Plate
    *2
    Front Clutch Disc

  1. C191350E04
    Install the snap ring.
    Text in Illustration 
    *1
    Front Clutch Disc
    *2
    Snap Ring

    NOTICE:
    1. Make sure the end gap of the snap ring is not aligned with the cutout portion of the front clutch drum.
    2. Be careful not to damage the front clutch drum.
    3. Make sure that the snap ring is inserted into the groove.

    HINT:
    Protective tape the screwdriver tip before use.

  1. Install the front clutch disc.


40. INSPECT PISTON STROKE OF FRONT CLUTCH PISTON

C191348
  1. In order to check the piston stroke, install the rear clutch hub.

  1. Install the snap ring.

  1. C191349E01
    Using SST and a dial indicator, measure the front clutch piston sub-assembly stroke by applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) as shown in the illustration.
    SST
    09350-20015   (09350-06120)

    Standard piston stroke:
    1.40 to 1.60 mm (0.0552 to 0.0629 in.)

    If the piston stroke is not as specified, parts may have been assembled incorrectly. Check the parts and reassemble again.

    HINT:
    1. If the piston stroke is still not as specified, replace the plates with ones of a different thickness.
    2. There are 2 types of plates that can be used to adjust the pack clearance. Select the one with the most appropriate thickness.

      Plate Thickness:
      Part No.
      Thickness
      35634-22040
      1.75 to 1.85 mm (0.0689 to 0.0728 in.)
      34634-30070
      1.95 to 2.05 mm (0.0768 to 0.0807 in.)


41. INSTALL FRONT CLUTCH HUB AND REAR CLUTCH HUB

  1. C191362E03
    Coat the bearing and races with MP grease and install them to the front clutch drum.

    Bearing and Race Diameter:
    Item
    Inside
    Outside
    Front Race E
    24.05 mm (0.947 in.)
    37.59 mm (1.48 in.)
    Bearing E
    23.34 mm (0.919 in.)
    37.59 mm (1.48 in.)
    Rear Race E
    21.41 mm (0.843 in.)
    37.59 mm (1.48 in.)

    Text in Illustration 
    *1
    Rear Race E
    *2
    Bearing E
    *3
    Front Race E

    NOTICE:
    Make sure the bearing and races are installed so that they are oriented correctly.

  1. C191363
    Install the front clutch hub to the front clutch drum.

    HINT:
    Mesh the splines of the front clutch hub with the teeth of the front clutch disc set by rotating and pushing the front clutch hub.

  1. C191364
    Install the rear clutch hub to the front clutch drum.

  1. Install the snap ring.

    NOTICE:
    1. Make sure the end gap of the snap ring is not aligned with the cutout portion of the front clutch drum.
    2. Be careful not to damage the front clutch drum.
    3. Make sure that the snap ring is inserted into the groove.

    HINT:
    Tape the screwdriver tip before use.

  1. C191482
    Remove the front clutch drum from the overdrive case sub-assembly.


42. INSTALL FRONT CLUTCH DRUM

  1. C191293E03
    Coat the 2 bearings and race with MP grease and install them to the front clutch drum.

    Bearing and Race Diameter:
    Item
    Inside
    Outside
    Bearing D
    23.34 mm (0.919 in.)
    37.59 mm (1.48 in.)
    Race F
    30.00 mm (1.18 in.)
    47.9 mm (1.89 in.)
    Bearing F
    28.30 mm (1.11 in.)
    46.48 mm (1.83 in.)

    Text in Illustration 
    *1
    Bearing D
    *2
    Race F
    *3
    Bearing F

    NOTICE:
    Make sure the bearings and race are installed so that they are oriented correctly.

  1. C191125
    Install the front clutch drum to the transmission case.

    HINT:
    Mesh the splines of the front clutch drum with the teeth of the rear clutch disc set by rotating and pushing the front clutch drum.


43. INSPECT INSTALLATION DISTANCE OF FRONT CLUTCH DRUM

  1. C191107E01
    Place SST on the transmission case.
    SST
    09350-20015   (09370-12010)

  1. Using a vernier caliper, measure the distance between the top of the front clutch drum and SST.
    If the measured distance is the same as the measured distance noted during disassembly, the front clutch drum is installed correctly.


44. INSTALL OVERDRIVE BRAKE PISTON
  1. Coat 2 new O-rings with ATF and install them to the overdrive brake piston.

  1. C191319
    Press the overdrive brake piston into the overdrive case sub-assembly by hand to install it.

    NOTICE:
    Be careful not to damage the O-rings.


45. INSTALL OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. C191320
    Install the overdrive brake return spring sub-assembly.

  1. C243160E02
    Install the snap ring while pushing the overdrive brake return spring sub-assembly with a screwdriver.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    1. Make sure the end gap of the snap ring is not aligned with the cutout portion of the overdrive transmission case.
    2. Be careful not to damage the automatic transmission extension housing.
    3. Make sure that the snap ring is inserted into the groove.

    HINT:
    Tape the screwdriver tip before use.


46. INSTALL OVERDRIVE PLANETARY RING GEAR SUB-ASSEMBLY

  1. C191322E03
    Coat the bearing and races with MP grease and install them to the overdrive case sub-assembly.

    Bearing and Race Diameter:
    Item
    Inside
    Outside
    Front Race C
    30.00 mm (1.18 in.)
    48.54 mm (1.91 in.)
    Bearing C
    28.30 mm (1.11 in.)
    46.48 mm (1.83 in.)
    Rear Race C
    27.58 mm (1.09 in.)
    44.70 mm (1.76 in.)

    Text in Illustration 
    *1
    Front Race C
    *2
    Bearing C
    *3
    Rear Race C

    NOTICE:
    Make sure the bearing and races are installed so that they are oriented correctly.

  1. Install the overdrive planetary ring gear.


47. INSTALL OVERDRIVE BRAKE DISC SET

  1. C191323E03
    Install the 3 plates, 3 overdrive brake discs and flange with the rounded edge of the flange facing upward.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2 - *3

    Text in Illustration 
    *1
    Plate
    *2
    Overdrive Brake Disc
    *3
    Flange

  1. Using a screwdriver, install the snap ring.

    NOTICE:
    1. Make sure the end gap of the snap ring is not aligned with the cutout portion of the overdrive case sub-assembly.
    2. Be careful not to damage the overdrive case sub-assembly.
    3. Make sure that the snap ring is inserted into the groove.

    HINT:
    Tape the screwdriver tip before use.


48. INSTALL OVERDRIVE BRAKE ASSEMBLY

  1. C191294E02
    Temporarily install SST to the transmission case.
    SST
    09350-20015   (09362-30011)

    HINT:
    Remove SST after installation of the oil pump assembly.

  1. C191106E04
    Coat the thrust washer and race with MP grease and install them to the overdrive case sub-assembly.

    Race Diameter:
    Item
    Inside
    Outside
    Race D
    24.05 mm (0.947 in.)
    37.59 mm (1.48 in.)

    Text in Illustration 
    *1
    Thrust Washer
    *2
    Race D

    NOTICE:
    Make sure the race is installed so that it is oriented correctly.

  1. Coat 2 new oil seal rings with ATF.

  1. C191318
    Connect the ends of the oil seal rings and install the oil seal rings to the overdrive case sub-assembly.

    NOTICE:
    Do not expand the rings excessively.

    HINT:
    After installing the oil seal rings, check that they rotate smoothly.

  1. C191461
    Slide the overdrive case sub-assembly onto the 2 guide bolts (SST) with the cutout portion of the overdrive case sub-assembly facing the transmission valve body assembly to install the overdrive case sub-assembly.


49. INSPECT PACK CLEARANCE OF OVERDRIVE BRAKE PISTON

C191311
  1. Place the overdrive case sub-assembly onto the transmission case with the cutout of the overdrive case sub-assembly facing downward.

    HINT:
    Make sure that the oil hole of the overdrive case sub-assembly is aligned with the oil hole of the transmission case.

  1. C191312
    Using a dial indicator, measure the overdrive brake disc set pack clearance by applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) as shown in the illustration.

    Standard pack clearance:
    0.75 to 1.25 mm (0.0296 to 0.0492 in.)

    If the piston stroke is not as specified, parts may have been assembled incorrectly. Check the parts and reassemble again.

    HINT:
    1. If the piston stroke is still not as specified, replace the plates with ones of a different thickness.
    2. There are 2 types of plates that can be used to adjust the pack clearance. Select the one with the most appropriate thickness.

    Plate Thickness:
    Part No.
    Thickness
    35634-30080
    1.95 to 2.05 mm (0.0768 to 0.0807 in.)
    34634-30010
    2.25 to 2.35 mm (0.0886 to 0.0925 in.)

  1. Remove the overdrive case sub-assembly from the transmission case.


50. INSTALL OVERDRIVE ONE-WAY CLUTCH

  1. C191467E04
    Install the overdrive one-way clutch to the outer race with the open end of the overdrive one-way clutch facing upward.
    Text in Illustration 
    *1
    One-way Clutch Retainer
    *2
    Overdrive One-way Clutch
    *3
    Outer Race
    *a
    Open End

  1. Install the 2 one-way clutch retainers.

  1. C295701E01
    Coat the bearing with MP grease and install it to the overdrive planetary gear assembly.

    Bearing Diameter:
    Item
    Inside
    Outside
    Bearing B
    37.3 mm (1.47 in.)
    52.52 mm (2.07 in.)

    Text in Illustration 
    *1
    Thrust Washer
    *2
    Overdrive One-way Clutch
    *3
    Bearing
    *a
    Open End

    NOTICE:
    Make sure the bearing and thrust washers are installed so that they are oriented correctly.

  1. Install the 2 washers and overdrive one-way clutch to the overdrive planetary gear assembly.

  1. C191338E03
    Using a screwdriver, install the snap ring.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    1. Be careful not to damage the overdrive planetary gear assembly.
    2. Make sure that the snap ring is inserted into the groove.

    HINT:
    Tape the screwdriver tip before use.


51. INSTALL OVERDRIVE DIRECT CLUTCH PISTON

  1. C191479
    Coat 2 new O-rings with ATF and install them to the overdrive direct clutch piston.

  1. Install the overdrive direct clutch piston.

  1. C191342E01
    Place SST on the overdrive direct clutch piston.
    SST
    09350-20015   (09369-20040)

  1. Press the overdrive direct clutch piston into the overdrive direct clutch drum by hand.

    NOTICE:
    Be careful not to damage the O-rings.


52. INSTALL OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. C191333
    Install the overdrive clutch return spring sub-assembly to the overdrive direct clutch drum.

  1. C191343E04
    Place SST on the overdrive clutch return spring sub-assembly and compress the overdrive clutch return spring sub-assembly with a press.
    SST
    09350-20015   (09369-20040)
    Text in Illustration 
    *a
    Claw

  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)

    NOTICE:
    1. Make sure the end gap of the snap ring is not aligned with the spring seat claw.
    2. Do not expand the snap ring ends excessively.
    3. Make sure that the snap ring is inserted into the groove.


53. INSTALL OVERDRIVE CLUTCH DISC SET

  1. C191468E03
    Install the cushion plate and flange with the rounded edge facing upward.

    Install in order:
    *1 - *2

    Text in Illustration 
    *1
    Cushion Plate
    *2
    Flange

  1. Using a screwdriver, install the snap ring.

    NOTICE:
    1. Make sure the end gap of the snap ring is not aligned with the cutout portion of the overdrive direct clutch drum.
    2. Be careful not to damage the overdrive direct clutch drum.
    3. Make sure that the snap ring is inserted into the groove.

    HINT:
    Tape the screwdriver tip before use.

  1. C191329
    Install the overdrive clutch disc.


54. INSTALL OVERDRIVE BRAKE HUB

  1. C191328
    Install the overdrive brake hub to the overdrive direct clutch drum.

  1. Using a screwdriver, install the snap ring.

    NOTICE:
    1. Make sure the end gap of the snap ring is not aligned with the cutout portion of the overdrive direct clutch drum.
    2. Be careful not to damage the overdrive direct clutch drum.
    3. Make sure that the snap ring is inserted into the groove.

    HINT:
    Tape the screwdriver tip before use.


55. INSPECT PISTON STROKE OF OVERDRIVE DIRECT CLUTCH PISTON

C191326
  1. Place the overdrive direct clutch drum sub-assembly onto the oil pump assembly.

  1. C191327
    Using a dial indicator, measure the overdrive direct clutch piston sub-assembly stroke by applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) as shown in the illustration.

    Standard piston stroke:
    1.74 to 2.44 mm (0.0686 to 0.0960 in.)

    If the result is not as specified, inspect the overdrive clutch disc set.

  1. Remove the overdrive direct clutch drum sub-assembly from the oil pump assembly.


56. INSTALL OVERDRIVE DIRECT CLUTCH DRUM

  1. C191325
    Install the overdrive direct clutch drum to the overdrive planetary gear assembly.

    HINT:
    Mesh the splines of the overdrive planetary gear assembly with the teeth of the overdrive clutch disc set by rotating and pushing the overdrive planetary gear assembly.


57. INSPECT OVERDRIVE ONE-WAY CLUTCH

  1. C191324
    Hold the overdrive direct clutch drum sub-assembly and turn the overdrive planetary gear assembly. Check that the overdrive planetary gear assembly can be turned clockwise but cannot be turned counterclockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free


58. INSTALL OVERDRIVE PLANETARY GEAR ASSEMBLY WITH OVERDRIVE DIRECT CLUTCH DRUM

  1. C191462E02
    Coat the thrust washer and race with MP grease and install them to the overdrive planetary gear assembly with overdrive direct clutch drum.

    Race Diameter:
    Item
    Inside
    Outside
    Race A
    24.32 mm (0.957 in.)
    39.2 mm (1.54 in.)

    Text in Illustration 
    *1
    Race A
    *2
    Thrust Washer

    NOTICE:
    Make sure the race is installed so that it is oriented correctly.

  1. C191103
    Install the overdrive planetary gear assembly with overdrive direct clutch assembly to the transmission case.

    HINT:
    Mesh the splines of the overdrive planetary gear assembly with the teeth of the overdrive brake disc set by rotating and pushing the overdrive planetary gear assembly.


59. INSPECT INSTALLATION DISTANCE OF OVERDRIVE DIRECT CLUTCH DRUM

  1. C191102E01
    Place SST on the transmission case.
    SST
    09350-20015   (09370-12010)

  1. Using a vernier caliper, measure the distance between the top of the overdrive direct clutch drum and SST.
    If the measured distance is the same as the measured distance noted during disassembly, the overdrive direct clutch drum is installed correctly.


60. INSTALL AUTOMATIC TRANSMISSION HOUSING

  1. C191082
    Coat a new O-ring with ATF and install it to the overdrive case sub-assembly.

  1. C295077E01
    Temporarily install the transmission housing with the 6 bolts.

  1. Tighten the bolts.

    Torque:
    for Bolt A:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }
    for Bolt B:
    57 N*m{ 579 kgf*cm , 42 ft.*lbf }


61. INSTALL OIL PUMP ASSEMBLY

  1. C191296
    Coat the bearing with MP grease and install it to the oil pump assembly.

    Bearing Diameter:
    Item
    Inside
    Outside
    Bearing A
    24.32 mm (0.957 in.)
    43.2 mm (1.70 in.)

    NOTICE:
    Make sure the race is installed so that it is oriented correctly.

  1. C191444
    Coat a new O-ring with ATF and install it to the oil pump assembly.

  1. C191298E01
    Slide the oil pump assembly onto SST (2 guide bolts) to install it.
    SST
    09350-20015   (09370-12010)

  1. Clean the 7 bolts.

  1. Apply adhesive to the bolt heads.

    Adhesive:
    Toyota Genuine Adhesive 1344,
    Three Bond 1344 or equivalent

  1. Temporarily install the 5 bolts.

  1. Using a screwdriver, remove SST.

  1. C191299
    Temporarily install the 2 bolts.

  1. Tighten the 7 bolts.

    Torque:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf }


62. INSPECT INPUT SHAFT ROTATION

  1. C191300
    Check that the input shaft rotates smoothly.


63. INSPECT OUTPUT SHAFT

C191301
  1. Using a dial indicator, measure the end play of the output shaft assembly while moving the output shaft assembly by hand.

    Standard end play:
    0.3 to 0.9 mm (0.0119 to 0.0354 in.)

    If the end play is not as specified, check for improper installation.

  1. Check that the output shaft assembly rotates smoothly.


64. INSPECT INDIVIDUAL PISTON OPERATION

  1. C191302E03
    Check for operating noise while applying compressed air to the oil holes indicated in the illustration.
    Text in Illustration 
    *a
    Overdrive Direct Clutch Oil Hole
    *b
    Overdrive Brake Oil Hole
    *c
    Rear Clutch Oil Hole
    *d
    Front Clutch Oil Hole
    *e
    No. 1 Brake Oil Hole
    *f
    No. 2 Brake Oil Hole
    *g
    No. 3 Brake Oil Hole
    If there is no noise, disassemble the parts and check the installation condition of the parts.


65. INSTALL PARKING LOCK PAWL SHAFT

  1. C191098E04
    Install a new E-ring to the parking lock pawl shaft.
    Text in Illustration 
    *1
    Parking Lock Pawl Shaft
    *2
    E-ring
    *3
    Parking Lock Pawl
    *4
    Spring

  1. Install the parking lock pawl, parking lock pawl shaft and spring.


66. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

  1. C191303
    Connect the parking lock rod sub-assembly to the manual valve lever to install it.


67. INSTALL PARKING LOCK PAWL BRACKET

  1. C191096
    Install the parking lock pawl bracket with the 2 washers and 2 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

  1. C191304
    Shift the manual valve lever to the P position, and then confirm that the front planetary ring gear is correctly locked by the parking lock pawl.


68. INSTALL ACCUMULATOR PISTON AND SPRING
  1. Coat 6 new O-rings with ATF and install them to each accumulator piston.

  1. C191305E02
    Install the 3 springs and 3 accumulator pistons to the 3 holes as shown in the illustration.

    Piston Diameter:
    Piston
    Outer Diameter
    C - 1
    31.85 mm (1.25 in.)
    C - 2
    31.85 mm (1.25 in.)
    B - 2
    34.8 mm (1.37 in.)

    Spring Diameter:
    Spring
    Free Length
    Outer Diameter
    Color
    C - 1
    75.03 mm (2.95 in.)
    17.00 mm (0.669 in.)
    White or Blue
    C - 2
    62.27 mm (2.45 in.)
    16.4 mm (0.646 in.)
    White or Purple
    B - 2
    56.40 mm (2.22 in.)
    18.79 mm (0.740 in.)
    Green

    Text in Illustration 
    *1
    C - 1 Accumulator Piston
    *2
    C - 2 Accumulator Piston
    *3
    B - 2 Accumulator Piston


69. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

  1. C191306
    Align the groove of the manual valve with the pin of the manual valve lever.

  1. C294429E01
    Install the valve body with the 17 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    HINT:
    Each bolt length is indicated below.
    Bolt A: 28 mm (1.10 in.)
    Bolt B: 30 mm (1.18 in.)
    Bolt C: 36 mm (1.42 in.)
    Bolt D: 45 mm (1.77 in.)


70. INSTALL TRANSMISSION WIRE

  1. C191094
    Coat a new O-ring with ATF, and install it to the transmission wire.

  1. Install the transmission wire to the transmission case with the bolt.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }

  1. C191093
    Connect the 4 connectors to the 4 shift solenoid valves.

  1. Install the clamp with the bolt to the transmission valve body assembly.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


71. INSTALL OVERDRIVE BRAKE TUBE

  1. C191092
    Using a plastic-faced hammer, tap in the overdrive brake tube as shown in the illustration.

    NOTICE:
    Be careful not to bend or damage the tube.


72. INSTALL VALVE BODY OIL STRAINER ASSEMBLY
  1. Install 3 new gaskets to the valve body oil strainer assembly.

  1. C191091
    Install the valve body oil strainer assembly with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


73. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

  1. C103253
    Install the 2 transmission oil cleaner magnets to the locations indicated in the illustration.

    NOTICE:
    Be careful not to spill oil on the contacting surfaces of the transmission case and automatic transmission oil pan sub-assembly.

  1. C191307
    Install a new automatic transmission oil pan gasket to the transmission case.

    HINT:
    Align the cutout part of the automatic transmission oil pan gasket with the transmission case.

  1. C191308
    Install the automatic transmission oil pan sub-assembly with the 14 bolts.

    Torque:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf }


74. INSTALL TRANSMISSION CASE REAR COVER

  1. C191089E04
    Install a new gasket and the transmission case rear cover with the 3 screws.
    Text in Illustration 
    *1
    Gasket
    *2
    Transmission Case Rear Cover


75. INSTALL SENSOR ROTOR

  1. C191088E05
    Using a snap ring expander, install the front side snap ring.
    Text in Illustration 
    *1
    Key
    *2
    Sensor Rotor
    *3
    Snap Ring

    NOTICE:
    1. Do not expand the snap ring ends excessively.
    2. Make sure that the snap ring is inserted into the groove.

  1. Install the key and sensor rotor.

  1. Using a snap ring expander, install the rear side snap ring.

    NOTICE:
    1. Do not expand the snap ring ends excessively.
    2. Make sure that the snap ring is inserted into the groove.


76. INSTALL EXTENSION HOUSING DUST DEFLECTOR

  1. C191309
    Using a screwdriver and hammer, tap in a new extension housing dust deflector.


77. INSTALL AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

  1. C295038E01
    Coat the lip of a new extension housing rear oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09309-37010  

    Standard depth:
    6.2 to 6.8 mm (0.245 to 0.267 in.)

    NOTICE:
    Be careful not to damage the lip of the extension housing rear oil seal.

  1. Install a new dust seal to a new retainer.

  1. C295039E01
    Using SST and a hammer, tap in the dust seal together with the retainer.
    SST
    09309-37010  

    Standard distance:
    0.7 to 1.3 mm (0.0276 to 0.0511 in.)


78. INSTALL EXTENSION HOUSING BUSH APPLY TUBE

  1. C191084E02
    Install the extension housing bush apply tube and a new bush apply tube gasket to the extension housing sub-assembly.
    Text in Illustration 
    *1
    Extension Housing Bush Apply Tube
    *2
    Bush Apply Tube Gasket


79. INSTALL EXTENSION HOUSING SUB-ASSEMBLY
  1. Clean and degrease the threads of the 6 bolts and the contact surfaces of the transmission case and the extension housing sub-assembly with non-residue solvent.

  1. Install a new gasket and the extension housing to the case.

  1. Apply adhesive to 2 or 3 threads on the end of the 6 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344,
    Three Bond 1344 or equivalent

  1. C114744E02
    Install the extension housing sub-assembly to the transmission case with the 6 bolts.

    Torque:
    36 N*m{ 370 kgf*cm , 27 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    for Bolt A: 35 mm (1.38 in.)
    for Bolt B: 45 mm (1.77 in.)


80. INSTALL SPEED SENSOR
  1. Coat a new O-ring with ATF and install it to the speed sensor SP2.

  1. C294426
    Install the speed sensor SP2 with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Coat a new O-ring with ATF and install it to the speed sensor NC0.

  1. Clean the bolt and the bolt hole.

  1. Apply adhesive to 2 or 3 threads on the end of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. C191076
    Install the speed sensor NC0 with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


81. INSTALL OIL COOLER TUBE UNION
  1. Coat 2 new O-rings with ATF and install one to each oil cooler tube union.

  1. C295079E01
    Using SST, install the 2 oil cooler tube unions.
    SST
    09268-78010  

    Torque:
    without SST:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }
    with SST:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }

    Text in Illustration 
    *a
    Fulcrum Length
    *b
    Turn
    *c
    Hold
    *d
    -13 to -17°
    *e
    -28 to -32°

    HINT:
    1. Use a torque wrench with a fulcrum length of 180 mm (7.09 in.). When using a torque wrench with a fulcrum length that is not 180 mm (7.09 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification.
    2. Make sure SST and the wrench are connected in a straight line.


82. INSTALL ATF TEMPERATURE SENSOR
  1. Coat the O-ring of the ATF temperature sensor with ATF.

  1. C295080
    Install the ATF temperature sensor.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }


83. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Clean the bolt and the bolt hole.

  1. Apply adhesive to 2 or 3 threads on the end of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. G034253E01
    Install the park/neutral position switch assembly to the manual valve lever shaft, and then temporarily install the bolt.

    HINT:
    Tighten the bolt to the specified torque when adjusting the park/neutral position switch assembly.

  1. Install a lock washer with the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Using the transmission control shaft lever LH, turn the manual valve lever shaft clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.

  1. D025795E25
    Align the neutral basic line with the groove of the park/neutral position switch assembly and tighten the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    Text in Illustration 
    *a
    Neutral Basic Line
    *b
    Groove

  1. Using a screwdriver, bend the tabs of the lock washer.


84. INSTALL TRANSMISSION CONTROL SHAFT LEVER LH

  1. C294428
    Install the transmission control shaft lever LH with the spring washer and nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }


85. INSTALL BREATHER HOSE SUB-ASSEMBLY

  1. C294425E01
    Install the No. 1 breather plug and No. 2 breather plug to the breather hose.
    Text in Illustration 
    *1
    No. 1 Breather Plug
    *2
    Breather Hose
    *3
    No. 2 Breather Plug

  1. C294424
    Install the breather hose sub-assembly to the transmission case.

  1. Install the clamp to the automatic transmission housing with the bolt.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


86. INSTALL DRAIN PLUG
  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }

← INSPECTION (Oct 2014 – Dec 2014)COMPONENTS (Oct 2014 – Dec 2014) →