2014-2019 Hiace · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from Oct 2014


CHECK INNER REAR VIEW MIRROR ASSEMBLY

  1. E247378E02
    Disconnect the u3 inner rear view mirror assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    u3-3 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    u3-6 (IG) - u3-3 (E)
    G - W-B
    Ignition switch signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    u3-5 (REV) - Body ground
    L - Body ground
    Reverse signal
    Ignition switch ON, shift lever not in R
    Below 1 V
    Ignition switch ON, shift lever in R
    11 to 14 V

  3. Reconnect the u3 inner rear view mirror assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    u3-1 (CV-) - u3-8 (CGND)
    W - Shielded
    Television camera ground
    Always
    Below 1 V
    u3-2 (CV+) - u3-8 (CGND)
    R - Shielded
    Display signal
    Ignition switch ON, shift lever in R
    Pulse generation (See waveform)
    u3-7 (CB+) - u3-8 (CGND)
    B - Shielded
    Power source
    Ignition switch ON, shift lever in R
    5.5 to 7.05 V
    u3-8 (CGND) - Body ground
    Shielded - Body ground
    Shielding
    Always
    Below 1 V

  5. Using an oscilloscope, check waveform.
    E241522E01

    Text in Illustration 
    *a
    Waveform A
    *b
    Waveform B
    *c
    Synchronization Signal
    *d
    Video Waveform

    HINT:
    The video waveform changes according to the image sent by the television camera assembly.

    Waveform 
    Item
    Content
    Terminal No. (Symbol)
    u3-2 (CV+) - u3-8 (CGND)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    1. Waveform A: Ignition switch ON, shift lever in R (camera lens is not covered, displaying an image).
    2. Waveform B: Ignition switch ON, shift lever in R (camera lens is covered, blacking out the screen).


CHECK TELEVISION CAMERA ASSEMBLY

  1. E252799E01
    Disconnect the a5 television camera assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    a5-5 (CGND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    a5-6 (CB+) - Body ground
    B - Body ground
    Power source
    Ignition switch ON, shift lever in R
    5.5 to 7.05 V

  3. Reconnect the a5 television camera assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    HINT:
    A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the rear view mirror assembly with the connector connected. If the result is not as specified, the television camera assembly may have a malfunction.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    a5-2 (CV-) - a5-5 (CGND)
    W - Shielded
    Television camera ground
    Always
    Below 1 V
    a5-3 (CV+) - a5-5 (CGND)
    R - Shielded
    Display signal
    Ignition switch ON, shift lever in R
    Pulse generation (See waveform)

  5. Using an oscilloscope, check waveform.
    E241522E01

    Text in Illustration 
    *a
    Waveform A
    *b
    Waveform B
    *c
    Synchronization Signal
    *d
    Video Waveform

    HINT:
    1. A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the inner rear view mirror assembly with the connector connected. If the result is not as specified, the television camera assembly may have a malfunction.
    2. The video waveform changes according to the image sent by the television camera assembly.

    Waveform 
    Item
    Content
    Terminal No. (Symbol)
    a5-3 (CV+) - a5-5 (CGND)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    1. Waveform A: Ignition switch ON, shift lever in R (camera lens is not covered, displaying an image).
    2. Waveform B: Ignition switch ON, shift lever in R (camera lens is covered, blacking out the screen).

← PROBLEM SYMPTOMS TABLE (from Dec 2017)Reverse Signal Circuit (Oct 2014 – Dec 2014) →