2014-2019 Hiace · Service Manual BODY ELECTRICAL

Reverse Signal Circuit

Circuit diagnosis · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2017 from Dec 2017

DESCRIPTION

The inner rear view mirror assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission

WIRING DIAGRAM

E247379E02

INSPECTION PROCEDURE


1. CHECK INNER REAR VIEW MIRROR ASSEMBLY (REVERSE SIGNAL)

  1. E254244E03
    Disconnect the inner rear view mirror assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    u3-5 (REV) - Body ground
    Ignition switch ON, shift lever in R
    11 to 14 V
    Ignition switch ON, shift lever not in R
    Below 1 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Inner Rear View Mirror Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Automatic Transmission)
    B
    NG (for Manual Transmission)
    C



B
Go to step 2

C
Go to step 4
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
  1. Disconnect the u3 inner rear view mirror assembly connector.

  1. Disconnect the D37 park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    u3-5 (REV) - D37-1 (RL)
    Always
    Below 1 Ω
    u3-5 (REV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Remove the park/neutral position switch assembly.

    1. for A340E: Click here
    2. for A343E: Click here
    3. for A45DE: Click here

  1. Inspect the park/neutral position switch assembly.

    1. for A340E: Click here
    2. for A343E: Click here
    3. for A45DE: Click here
    Result 
    Result
    Proceed to
    OK
    A
    NG (for A340E)
    B
    NG (for A343E)
    C
    NG (for A45DE)
    D



B
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

C
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

D
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
A

REPLACE INNER REAR VIEW MIRROR ASSEMBLY (Click here)

4. CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the u3 inner rear view mirror assembly connector.

  1. Disconnect the D36 back-up light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    u3-5 (REV) - D36-1
    Always
    Below 1 Ω
    u3-5 (REV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT BACK-UP LIGHT SWITCH ASSEMBLY
  1. Remove the back-up light switch assembly.

    1. for G55: Click here
    2. for R351: Click here

  1. Inspect the back-up light switch assembly.

    1. for G55: Click here
    2. for R351: Click here
    Result 
    Result
    Proceed to
    OK
    A
    NG (for G55)
    B
    NG (for R351)
    C



B
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)

C
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)
A

REPLACE INNER REAR VIEW MIRROR ASSEMBLY (Click here)


← TERMINALS OF ECU (from Oct 2014)Reverse Signal Circuit (Jan 2015 – Nov 2017) →