2014-2019 Hiace · Service Manual ENGINE

P052F Glow Plug Control Module System Voltage

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

The glow system consists of the glow plug controller, glow plugs and ECM. The glow plug controller turns on the glow plug of each cylinder according to the duty command signal from the ECM in order to maintain optimal engine temperatures. The glow plugs can be controlled according to the engine coolant temperature at engine start by using duty signals. This helps induce ignition under low temperatures and prevent rough idle after starting the engine.
The glow plugs are turned on during PM forced regeneration in order to prevent the engine speed from rising due to an increase in fuel injection volume used to increase the exhaust gas temperature. The glow plug controller contains a self-diagnosis function. When the glow plug controller detects an internal malfunction, it sends a signal indicating the malfunction to the ECM. When the ECM receives this signal, it illuminates the MIL and stores a DTC.
P052F 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
The glow plug controller recognizes the battery voltage as being 18.4 V or higher 3 times or more when the glow plugs are on (2 trip detection logic).
Glow plug controller
P0683 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
When the glow plugs are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal) (2 trip detection logic).
  1. Open or short circuit in ground wire
  2. Open or short circuit in battery wire
  3. Open in SI wire
  4. SI wire short circuit to ground or battery
  5. Open in DI wire
  6. DI wire short circuit to ground or battery
  7. Low battery voltage
  8. Glow plug controller
  9. ECM

WIRING DIAGRAM

A399329E01

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0683 is output
    A
    DTC P052F is output
    B



B
Go to step 12
A


2. CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)

  1. A241954E17
    Disconnect the glow plug controller connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B67-4 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    B67-4 (+B) - Body ground
    Ignition switch off
    Below 0.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Glow Plug Controller)

  1. Reconnect the glow plug controller connector.



NG
Go to step 5
OK


3. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)

  1. A241954E18
    Disconnect the glow plug controller connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B67-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the glow plug controller connector.



NG
Go to step 7
OK


4. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)
  1. Disconnect the glow plug controller connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B67-3 (SI) - D134-7 (GLDO)
    Always
    Below 1 Ω
    B67-5 (DI) - D134-37 (GLDI)
    Always
    Below 1 Ω
    B67-3 (SI) or D134-7 (GLDO) - Body ground and other terminals
    Always
    10 kΩ or higher
    B67-5 (DI) or D134-37 (GLDI) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the glow plug controller connector.

  1. Reconnect the ECM connector.



OK
Go to step 8

NG
Go to step 7
5. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - EFI NO. 2 RELAY)
  1. Disconnect the glow plug controller connector.

  1. Remove the EFI NO. 2 relay from the engine room relay block No. 2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B67-4 (+B) - EFI NO. 2 relay terminal 5
    Always
    Below 1 Ω
    B67-4 (+B) or EFI NO. 2 relay terminal 5 - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the glow plug controller connector.

  1. Reinstall the EFI NO. 2 relay.



NG
Go to step 7
OK


6. CHECK CHARGING SYSTEM
  1. Check the charging system and perform repairs as necessary (Click here).



NEXT
Go to step 13
7. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 13
8. REPLACE GLOW PLUG CONTROLLER
  1. Replace the glow plug controller (Click here).


NEXT


9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Using the GTS, switch the ECM from normal mode to check mode (Click here).

  1. Confirm that the DTC is not output again.

    HINT:
    Check for DTCs in check mode.



NG
Go to step 10
OK

END

10. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Using the GTS, switch the ECM from normal mode to check mode (Click here).

  1. Confirm that the DTC is not output again.

    HINT:
    Check for DTCs in check mode.


NEXT

END

12. REPLACE GLOW PLUG CONTROLLER
  1. Replace the glow plug controller (Click here)


NEXT


13. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Using the GTS, switch the ECM from normal mode to check mode (Click here).

  1. Confirm that the DTC is not output again.

    HINT:
    Check for DTCs in check mode.


NEXT

END


← P0504 Brake Switch "A" / "B" Correlation (from Jan 2017)P0545 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1) (+ P0546) (from Jan 2017) →