2014-2019 Hiace · Service Manual TRANSMISSION

INSPECTION

Inspection · Vehicles built from Jan 2015


INSPECT SHIFT LOCK CONTROL ECU

HINT:
Do not disconnect the shift lock control unit assembly connector.

  1. C297187E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    5 (KLS+) - 1 (E)
    Ignition switch ACC and shift lever in P
    Below 1 V
    Ignition switch ACC and shift lever not in P
    11 to 14 V
    6 (ACC) - 1 (E)
    Ignition switch ACC
    11 to 14 V
    Ignition switch off
    Below 1 V
    4 (STP) - 1 (E)
    Brake pedal depressed
    11 to 14 V
    Brake pedal released
    Below 1 V
    8 (IG) - 1 (E)
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    10 (SLS-) - 1 (E)
    Ignition switch ON, brake pedal depressed and shift lever in P
    Below 2.5 V
    Ignition switch ON, brake pedal released and shift lever in P
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Shift Lock Control ECU)
    If the result is not as specified, replace the shift lock control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (E) - Body ground
    Always
    Below 1 Ω

    If the result is not as specified, replace the shift lock control ECU.


INSPECT SHIFT LOCK SOLENOID
  1. Disconnect the shift lock solenoid connector from the shift lock control ECU.

  1. C097709E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (P) - 3 (E2)
    Shift lever in P
    10 kΩ or higher
    Shift lever not in P
    Below 1 Ω
    1 (SLS+) - 2 (SLS-)
    Always
    112 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Shift Lock Solenoid)
    If the result is not as specified, replace the shift lock control unit assembly.


INSPECT TRANSMISSION CONTROL SWITCH
  1. Disconnect the transmission control switch connector.

  1. C199170E27
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    5 (SFTU) - 11 (E)
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    4 (SFTD) - 11 (E)
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    6 (IG) - 13 (S)
    Shift lever in S, "+" or "- "
    Below 1 Ω
    5 (SFTU) - 11 (E)
    Shift lever not held in "+"
    10 kΩ or higher
    4 (SFTD) - 11 (E)
    Shift lever not held in "- "
    10 kΩ or higher
    6 (IG) - 13 (S)
    Shift lever not in S, "+" or "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch)
    If the result is not as specified, replace the shift lock control unit assembly.

← DISASSEMBLY (from Jan 2015)ADJUSTMENT (from Jan 2015) →