P1604 Startability Malfunction
Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017
Versions by build date: Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
This DTC is stored when the engine does not start even though the STA signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts.Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when there is engine starting trouble due to running out of fuel.
| DTC No. |
DTC Detection Condition |
| P1604 |
Either conditions is met:
|


| Ignition system |
|
| Fuel system |
|
| Intake and exhaust systems |
|
| Other control systems |
|
| Engine |
|
| High load from another system |
|
INSPECTION PROCEDURE
- In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.
As this DTC can be stored as a result of certain user actions, even if the DTC is output, if the customer makes no mention of problems, clear the DTC without performing any troubleshooting and return the vehicle to the customer.
- If any other DTCs are output, perform troubleshooting for those DTCs first.
- When this Data List item "Immobiliser Fuel Cut" is ON, the engine cannot be started.
- Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
- When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data. (Click here)
- When confirming the freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
- If the same inspection or replacement procedure appears 2 times when performing an inspection procedure, it is not necessary to repeat the procedure the second time.
| 1. CHECK FOR ANY OTHER DTCS OUTPUT |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
- Result:
Result
Proceed to
Only DTC P1604 is output
A
DTCs other than P1604 are output
B
- HINT:
- If any DTCs other than P1604 is output, troubleshoot those DTCs first.
- Using freeze frame data, confirm the conditions the moment the DTC was stored and after the DTC was stored. This information can be useful when troubleshooting.
- If any DTCs other than P1604 is output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. READ FREEZE FRAME DATA (IMMOBILISER COMMUNICATION AND IMMOBILISER FUEL CUT) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored. (Click here)
- OK:
Data List Item
GTS Display
Immobiliser Communication
ON
Immobiliser Fuel Cut
OFF
- HINT:
- If the engine is started immediately after reconnecting the battery terminal, the engine may stall immediately after it starts due to the intercommunication process between each ECU. For this reason, when starting the engine after reconnecting the battery terminal, first turn the ignition switch to ON and then wait several seconds for the communication process to complete before starting the engine.
|
|
||||
| OK | |
| 3. READ FREEZE FRAME DATA (ISC LEARNING VALUE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored. (Click here)
- Result:
Freeze Frame Data Item for DTC P1604
Result
Suspected Area
Action
Proceed to
ISC Learning Value
Less than 6.2 L/s
-
Go to the next step
A
6.2 L/s or higher
Throttle valve assembly
Go to Engine Difficult to Start (from step 15 (REMOVE FOREIGN OBJECT (CLEAN THROTTLE BODY ASSEMBLY))
B
|
|
||||
| A | |
| 4. READ FREEZE FRAME DATA (ENGINE SPEED) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored. (Click here)
- Result:
Freeze Frame Data Item
Result
Suspected Area
Action
Proceed to
Engine Speed
All 5 sets of freeze frame data are 0 rpm (engine did not crank or engine speed was not detected properly)
- Starter signal circuit
- Crankshaft position sensor system
- Battery fully depleted
Go to Engine Difficult to Start (from step 5 (CHECK CRANKING))
A
100 to 500 rpm (engine cranked but initial combustion did not occur or was delayed)
- Fuel pump
- Leaking fuel injector assembly
- Spark plug
- Ignition coil assembly
Go to the next step
B
500 rpm or higher (engine speed dropped immediately after initial combustion) (Low Rev for Eng Start is ON)
- Spark plug
- Ignition coil assembly
- Starter signal circuit
|
|
||||
| B | |
| 5. INTERVIEW THE CUSTOMER |
Interview the customer for details about the conditions when the malfunction occurred.
- HINT:
- If the engine is difficult to start only when the vehicle has been left as is for a long time, a leaking fuel injector assembly is suspected.
- Result:
Result
Suspected Area
Action
Proceed to
Engine is difficult to start only when the vehicle has been left as is for a long time (1 hour or more)
Leaking fuel injector assembly
Go to Engine Difficult to Start (from step 4 (INSPECT FUEL INJECTOR ASSEMBLY))
A
Other than above
- Fuel pump
- Spark plug
- Ignition coil assembly
Go to the next step
B
- Fuel pump
|
|
||||
| B | |
| 6. INTERVIEW THE CUSTOMER |
Interview the customer for details about the conditions when the malfunction occurred.
- HINT:
- If the engine is difficult to start only when the vehicle has been left as is for a long time, a leaking fuel injector assembly is suspected.
- Result:
Result
Suspected Area
Action
Proceed to
Mostly driven short distances
- Spark plug
- Ignition coil assembly
Go to Engine Difficult to Start (from step 13 (CHECK IGNITION SYSTEM))
NEXT
Not mostly driven short distances
- Fuel pump
- Spark plug
- Ignition coil assembly
Go to Engine Difficult to Start (from step 9 (READ VALUE USING GTS (SHORT FT AND LONG FT))
- Spark plug
| NEXT | ||
| ||
