2014-2019 Hiace · Service Manual SECURITIES

HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshooting · Vehicles built Jan 2017 – Nov 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

HINT:
  1. Use this procedure to troubleshoot the immobiliser system.
  2. *: Use the GTS.


1.VEHICLE BROUGHT TO WORKSHOP
    NEXT

    2.CUSTOMER PROBLEM ANALYSIS

      HINT:
      1. In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      2. Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
      3. The following 5 items are important points for problem analysis:

      What
      Vehicle model, system name
      When
      Date, time, occurrence frequency
      Where
      Whether the problem occurs at a specific location.
      Under what conditions?
      Whether the doors were locked or unlocked, whether the ignition switch was ON, whether the engine was running.
      How did it happen?
      Problem symptoms
    NEXT

    3.INSPECT BATTERY VOLTAGE
    1. Measure the battery voltage.

      Standard voltage:
      11 to 14 V

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

    NEXT

    4.CRANK ENGINE FOR MORE THAN 10 SECONDS
      NEXT

      5.CHECK FOR DTC* (ECM)
      1. Check for DTCs and note any codes that are output.

        HINT:
        Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

        Result 
        Result
        Proceed to
        DTCs are not output
        A
        SFI system DTCs are output (for 1TR-FE [w/ Dual VVT-i])
        B
        SFI system DTCs are output (for 2TR-FE [w/ Secondary Air Injection System])
        C
        SFI system DTCs are output (for 2TR-FE [w/o Secondary Air Injection System])
        D
        SFI system DTCs are output (for 2TR-FE [w/ Dual VVT-i])
        E
        ECD system DTCs are output (for 1KD-FTV [w/o DPF])
        F
        ECD system DTCs are output (for 1KD-FTV [w/ DPF])
        G
        ECD system DTCs are output (for 2KD-FTV)
        H
        Immobiliser system DTCs are output
        I


      B.

      C.

      D.

      E.

      F.

      G.

      H.

      I.
      A

      6.CHECK FOR DTC* (TRANSPONDER KEY ECU ASSEMBLY)
      1. Check for DTCs and note any codes that are output (Click here).

        HINT:
        Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

        Result 
        Result
        Proceed to
        DTCs are not output
        A
        Immobiliser system DTCs are output
        B


      B.
      A

      7.PROBLEM SYMPTOMS TABLE
      1. Refer to Problem Symptoms Table (Click here).

        Result 
        Result
        Proceed to
        Fault is not listed in problem symptoms table
        A
        Fault is listed in problem symptoms table
        B


      B.
      A

      8.OVERALL ANALYSIS AND TROUBLESHOOTING*
      1. Data List / Active Test (Click here).

      2. Terminals of ECU (Click here).

      NEXT

      9.REPAIR OR REPLACE

        HINT:
        If the transponder key ECU assembly, ECM, or key are replaced, refer to Service Bulletin.

      NEXT

      10.CHECK FOR DTC*
      1. Clear the DTCs (Click here).

      2. Check for DTCs (Click here).

        HINT:
        Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

        Result 
        Result
        Proceed to
        DTCs are not output
        A
        Immobiliser system DTCs are output
        B


      B.
      A

      ← HOW TO PROCEED WITH TROUBLESHOOTING (Apr 2016 – Dec 2016)HOW TO PROCEED WITH TROUBLESHOOTING (from Dec 2017) →