2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jan 2017

NOTICE:
  1. When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
    Replaced Parts (A)
    Pipes Requiring New Replacement
    Injector assembly (including shuffling the injector assemblies between the cylinders)
    1. No. 1 injection pipe sub-assembly
    2. No. 2 injection pipe sub-assembly
    Supply pump assembly
    Fuel inlet pipe sub-assembly
    1. Common rail assembly
    2. Cylinder block sub-assembly
    3. Cylinder head sub-assembly
    4. Cylinder head gasket
    5. Timing chain case assembly
    1. Fuel inlet pipe sub-assembly
    2. No. 1 injection pipe sub-assembly
    3. No. 2 injection pipe sub-assembly
  2. After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
  3. The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
  4. Make sure foreign matter does not enter the fuel path.
  5. The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
  6. Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.


1. REMOVE ENGINE ASSEMBLY
(Click here)

2. REMOVE ENGINE WIRE

3. REMOVE INTERCOOLER AIR TUBE

  1. A398588
    Remove the 2 bolts and air tube support bracket.

  1. A398589
    Disconnect the connector from the intake air temperature sensor.

  1. Loosen the hose clamp and remove the intercooler air tube from the diesel throttle body assembly.


4. REMOVE DIESEL THROTTLE BODY ASSEMBLY

  1. A398591
    Disconnect the connector and clamp.

  1. Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.

  1. A345996
    Disconnect the connector to remove the emission control valve wire from the diesel throttle body assembly.


5. REMOVE NO. 2 WATER BY-PASS PIPE

  1. A388388E01
    Remove the 2 bolts and No. 2 water by-pass pipe.


6. REMOVE DIFFERENTIAL PRESSURE SENSOR

  1. A396478
    Disconnect the connector from the differential pressure sensor.

  1. Remove the bolt and differential pressure sensor from the pipe clamp.

  1. A396479
    Slide the 2 clamps and disconnect the 2 air hoses from the No. 1 vacuum pipe and No. 2 vacuum pipe.

  1. A352099
    Slide the 2 clamps and remove the 2 air hoses from the differential pressure sensor.


7. REMOVE EXHAUST GAS TEMPERATURE SENSOR

CAUTION:
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

  1. A396505
    Disconnect the 3 connectors from the 3 exhaust gas temperature sensors.

  1. A396506
    Remove the nut and disconnect the No. 3 exhaust gas temperature sensor from the No. 1 vacuum pipe.

  1. A396507
    Remove the bolt and open the clamp of the pipe clamp.

  1. Detach the 3 connectors from the pipe clamp.

  1. A396508
    Using a 14 mm union nut wrench, remove the exhaust gas temperature sensor from the exhaust manifold converter sub-assembly.

  1. A396509
    Using a 14 mm union nut wrench, remove the No. 2 exhaust gas temperature sensor from the exhaust manifold converter sub-assembly.

  1. A396510
    Using a 14 mm union nut wrench, remove the No. 3 exhaust gas temperature sensor from the exhaust manifold converter sub-assembly.


8. REMOVE NO. 1 VACUUM PIPE

  1. A396492
    Remove the nut and clamp from the No. 1 vacuum pipe and No. 2 vacuum pipe.

  1. A396493
    Using a 17 mm union nut wrench, remove the No. 1 vacuum pipe from the exhaust manifold converter sub-assembly.


9. REMOVE NO. 2 VACUUM PIPE

  1. A396494
    Using a 17 mm union nut wrench, remove the No. 2 vacuum pipe from the exhaust manifold converter sub-assembly.

  1. A396495
    Remove the clamp from the pipe clamp.


10. REMOVE PIPE CLAMP

  1. A396496
    Remove the 3 bolts and pipe clamp from the engine cover bracket.


11. REMOVE ENGINE COVER BRACKET

  1. A381071
    Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.


12. REMOVE GAS FILTER

  1. A396754
    Disconnect the 2 vacuum hoses from the turbo pressure sensor and intake manifold.

  1. Remove the gas filter from the gas filter bracket.


13. REMOVE DIESEL TURBO PRESSURE SENSOR

  1. A398609
    Disconnect the diesel turbo pressure sensor connector.

  1. Remove the bolt and diesel turbo pressure sensor.

  1. Disconnect the vacuum hose from the diesel turbo pressure sensor.


14. REMOVE EGR VALVE BRACKET

  1. A396757
    Remove the bolt, nut and EGR valve bracket from the electric EGR control valve assembly and intake manifold.


15. REMOVE NO. 2 EGR PIPE

  1. A396758
    Remove the bolt, 4 nuts and No. 2 EGR pipe from the electric EGR control valve assembly and intake manifold.

  1. Remove the 2 gaskets.


16. REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A396761
    Disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.

  1. A396779
    Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.

  1. Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.

  1. Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the No. 1 EGR cooler.


17. REMOVE CONNECTING WIRE

  1. A381073
    Disconnect the connector from the common rail assembly.

  1. Detach the 2 clamps and remove the connecting wire from the bracket.


18. REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

  1. A381074
    Remove the 4 nuts, bolt and No. 1 EGR pipe sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.

  1. Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.

  1. A381096
    Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


19. REMOVE VACUUM CONTROL VALVE SET
  1. Disconnect the connector from the vacuum control valve set.

  1. A396768
    Disconnect the 2 vacuum hoses from the vacuum control valve set and No. 2 EGR valve assembly.

  1. A396769
    Remove the 2 bolts and vacuum control valve set from the intake manifold.


20. REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A381075E01
    Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.
    Text in Illustration 
    *1
    No. 6 Water By-pass Hose
    *2
    No. 7 Water By-pass Hose
    *3
    Water Hose

  1. Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.

  1. Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.

  1. Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.


21. REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

  1. A396780
    Remove the 4 bolts and No. 1 EGR cooler and No. 2 EGR valve assembly with electric EGR control valve assembly from the intake manifold.


22. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A418026E01
    w/ No. 2 Fuel Pipe Clamp:
    Detach the No. 2 fuel pipe clamp from the engine oil level dipstick guide.

  1. Remove the engine oil level dipstick.

  1. Slide the clip and disconnect vacuum hose from the intake manifold.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring and grommet from the engine oil level dipstick guide.


23. REMOVE NO. 2 FUEL PIPE

  1. A381076
    Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.

  1. Remove the bolt and No. 2 fuel pipe from the manifold stay.


24. REMOVE WIRING HARNESS CLAMP BRACKET

A398352
  1. Disconnect the diesel throttle body assembly connector and pre-stroke control valve connector.

  1. A353379
    Detach the 2 wire harness clamps.

  1. Remove the bolt and wiring harness clamp bracket.


25. REMOVE MANIFOLD STAY

A398353
  1. Remove the bolt and disconnect the wiring harness clamp bracket from the manifold stay.

  1. A398354
    Remove the 2 bolts and manifold stay.


26. REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

A353390
  1. Remove the fuel injection pump cover sub-assembly from the supply pump assembly.


27. REMOVE FUEL PUMP MOTOR WIRE

A401178
  1. Disconnect the fuel pump motor wire connector and remove the fuel pump motor wire.


28. REMOVE NO. 2 FUEL HOSE
  1. Slide the 2 clips and remove the No. 2 fuel hose from the supply pump assembly and No. 3 nozzle leakage pipe assembly.


29. REMOVE NO. 1 FUEL HOSE

A353389
  1. Slide the 2 clips and remove the No. 1 fuel hose from the supply pump assembly and No. 2 fuel pipe.


30. REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY

A356214E01
  1. Disconnect the No. 4 fuel pipe sub-assembly from the No. 1 fuel pipe (Click here).

    Text in Illustration 
    V100136
    Union Bolt
    V100137
    Bolt

  1. Remove the bolt from the intake manifold.

  1. Remove the 2 union bolts and 2 gaskets from the supply pump assembly and fuel filter.


31. REMOVE NO. 3 FUEL PIPE
(Click here)

32. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

A353386E01
Text in Illustration 
*a
Common Rail Assembly Side
*b
Fuel Supply Pump Assembly Side
  1. Remove the 2 bolts, No. 1 injection pipe clamp and No. 2 injection pipe clamp.

  1. A375573E01
    Using SST, loosen the fuel inlet pipe sub-assembly union nut of the common rail assembly side.
    SST
    09245-11010  

    NOTICE:
    If the No. 1 or No. 2 injection pipe clamp is removed from the inlet pipe sub-assembly, replace the No. 1 or No. 2 injection clamp with a new one.

  1. Using a 19 mm union nut wrench, loosen the inlet pipe sub-assembly union nut of the fuel supply pump assembly side.


33. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

A345101
  1. Slide the 2 clamps and remove the No. 4 fuel hose from the No. 2 nozzle leakage pipe assembly and common rail assembly.

  1. Slide the 2 clamps and remove the No. 5 fuel hose from the No. 1 nozzle leakage pipe assembly and No. 2 nozzle leakage pipe assembly.

  1. A345102
    Slide the clamp and disconnect the No. 6 fuel hose from the No. 3 nozzle leakage pipe assembly.

  1. Remove the 2 bolts and No. 2 nozzle leakage pipe assembly.


34. REMOVE INTAKE MANIFOLD
  1. Remove the bolt and disconnect the wire harness bracket.

  1. A401169
    Remove the 7 bolts, 2 nuts, intake manifold and gasket.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut


35. REMOVE WIRING HARNESS CLAMP BRACKET

  1. A339108
    Disconnect the pressure discharge valve connector from the common rail assembly.

  1. Remove the bolt and wiring harness clamp bracket from the cylinder head cover sub-assembly.


36. REMOVE NO. 1 FUEL PIPE

  1. A396486
    Remove the bolt, union bolt and gasket and disconnect the No. 1 fuel pipe from the cylinder head cover sub-assembly and exhaust fuel addition injector assembly.

  1. A396487
    Disconnect the No. 4 fuel pipe and remove the No. 1 fuel pipe (Click here).


37. REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

NOTICE:
After removing the No. 1 and No. 2 injection pipe sub-assemblies, cover the common rail assembly with electrical tape to prevent dirt or foreign objects from entering the pipe inlet. Also, protect the injector inlets with electrical tape or plastic bags.

  1. A398342E01
    Using SST, loosen the No. 1 and No. 2 injection pipe sub-assemblies and 8 union nuts of the fuel injector assembly side and common rail assembly side.
    SST
    09245-11010  

  1. A339111
    Remove the 2 No. 1 injection pipe sub-assemblies and 2 No. 2 injection pipe sub-assemblies.

    NOTICE:
    When removing the No. 1 injection pipe sub-assembly and No. 2 injection pipe sub-assembly, store the injector assemblies in the correct order so that they can be returned to their original locations when reassembling.


38. REMOVE WIRING HARNESS CLAMP BRACKET

  1. A381077
    for Upper Side:
    Remove the bolt and wiring harness clamp bracket from the cylinder head cover sub-assembly.

  1. A381078
    for Rear Side:
    Remove the bolt and wiring harness clamp bracket from the cylinder block sub-assembly.


39. REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
After removing the No. 1 and No. 2 injection pipe sub-assemblies, cover the common rail assembly with electrical tape to prevent dirt or foreign objects from entering the pipe inlet. Also, protect the injector inlets with electrical tape or plastic bags.

  1. A398342E01
    Using SST, loosen the No. 1 and No. 2 injection pipe sub-assemblies and 8 union nuts of the fuel injector assembly side and common rail assembly side.
    SST
    09245-11010  

  1. A339111
    Remove the 2 No. 1 injection pipe sub-assemblies and 2 No. 2 injection pipe sub-assemblies.

    NOTICE:
    When removing the No. 1 injection pipe sub-assembly and No. 2 injection pipe sub-assembly, store the injector assemblies in the correct order so that they can be returned to their original locations when reassembling.


40. REMOVE HOSE BRACKET

  1. A381079
    Remove the 2 bolts and bracket from the cylinder head sub-assembly.


41. REMOVE COOLER COMPRESSOR ASSEMBLY

42. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

  1. A381081
    Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.


43. REMOVE PCV HOSE

  1. A398355
    Slide the 2 clips, detach the clamp and remove the PCV hose.


44. REMOVE NO. 5 WATER BY-PASS HOSE

  1. A381082
    Slide the 2 clamps and disconnect the No. 5 water by-pass hose from the No. 1 injector holder and water outlet sub-assembly.

  1. Detach the clamp and remove the No. 5 water by-pass hose from the hose clamp.


45. REMOVE NO. 4 WATER BY-PASS HOSE

  1. A381083
    Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 injector holder.


46. REMOVE NO. 1 INJECTOR HOLDER

  1. A396489
    Disconnect the connector from the exhaust fuel addition injector assembly.

  1. A396490
    Remove the 3 nuts and No. 1 injector holder from the exhaust manifold.


47. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A343917
    Remove the 3 nuts and No. 2 exhaust manifold heat insulator from the No. 1 injector holder.

  1. Remove the gasket.


48. REMOVE AIR FUEL RATIO SENSOR

CAUTION:
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

  1. A398612E01
    Disconnect the connector.

  1. Using SST, remove the air fuel ratio sensor.

    SST
    09224-00012  


49. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A396498
    Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.


50. REMOVE NO. 1 TURBO INSULATOR

  1. A396499
    Remove the 3 bolts and No. 1 turbo insulator from the exhaust manifold and turbocharger sub-assembly.


51. REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY

  1. A396500
    Remove the bolt, 2 nuts and No. 2 exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.


52. REMOVE EXHAUST PIPE SUPPORT STAY

  1. A396501
    Remove the 3 bolts and exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.


53. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

  1. A396502
    Remove the nut, exhaust pipe clamp and exhaust manifold converter sub-assembly from the turbocharger sub-assembly.

  1. Remove the gasket.


54. REMOVE FRONT ENGINE MOUNTING INSULATOR RH

55. REMOVE FRONT ENGINE MOUNTING INSULATOR

56. REMOVE NO. 1 WATER BY-PASS PIPE

  1. A381084
    Remove the 2 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.


57. REMOVE NO. 1 AND NO. 2 TURBO WATER HOSE

A352794
  1. Slide the clip and disconnect the No. 1 turbo water hose from the water pump assembly.

  1. Slide the clip and disconnect the No. 2 turbo water hose from the water outlet sub-assembly.


58. REMOVE TURBOCHARGER STAY

A353383
  1. Remove the 3 bolts, nut and turbocharger stay.


59. REMOVE TURBO OIL OUTLET PIPE

A344956
  1. Slide the 2 clips and disconnect the turbo oil outlet hose from the turbo oil outlet pipe.

  1. Remove the 2 bolts, turbo oil outlet pipe and gasket.


60. REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

A344957
  1. Remove the union bolt and gasket.

  1. A398359
    A344974E01
    Remove the 2 nuts and turbo oil inlet pipe sub-assembly.

    NOTICE:
    Do not loosen the nut labeled A.

  1. Remove the gasket.


61. REMOVE TURBOCHARGER SUB-ASSEMBLY

  1. A398360
    Remove the 3 nuts and turbocharger sub-assembly.

  1. Remove the gasket from the turbocharger sub-assembly.


62. REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A381085
    Slide the clamp and disconnect the No. 3 water by-pass hose from the water outlet sub-assembly.

  1. Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly from the engine water pump assembly and water inlet.


63. REMOVE WATER OUTLET SUB-ASSEMBLY

  1. A381086
    Remove the 4 bolts, 2 nuts and water outlet sub-assembly from the timing chain cover sub-assembly.

  1. Remove the gasket from the timing chain cover sub-assembly.


64. REMOVE WATER INLET

  1. A397677
    Remove the 2 bolts and water inlet from the engine water pump assembly.


65. REMOVE THERMOSTAT
  1. Remove the thermostat from the engine water pump assembly.

  1. Remove the gasket from the thermostat.


66. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A339577
    Remove the bolt and No. 1 idler pulley sub-assembly from the generator bracket sub-assembly.


67. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A339579
    Remove the 3 bolts and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.


68. REMOVE CRANKSHAFT PULLEY COVER

  1. A343925
    Remove the 4 bolts and crankshaft pulley cover from the crankshaft pulley.


69. REMOVE CRANKSHAFT PULLEY

  1. A343926E01
    Using SST, hold the crankshaft pulley and loosen the pulley bolt.
    SST
    09213-58014  
    (91551-80840)
    09330-00021  

    HINT:
    Make sure to leave the pulley bolt screwed into the crankshaft by 2 or 3 threads.

  1. A343927E01
    Using SST, remove the pulley bolt and crankshaft pulley from the crankshaft.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


70. REMOVE NO. 1 ENGINE HANGER

  1. A343515
    Remove the 2 bolts and No. 1 engine hanger from the cylinder head sub-assembly.


71. REMOVE GENERATOR BRACKET SUB-ASSEMBLY

  1. A343519
    Remove the 4 bolts and generator bracket sub-assembly from the cylinder head sub-assembly and timing chain case assembly.


72. REMOVE INJECTOR ASSEMBLY

  1. A344925
    Remove the 4 nozzle holder clamp bolts, 4 washers and 4 nozzle holder clamps.

  1. Remove the 4 fuel injector assemblies and 4 injection nozzle seats from the cylinder head sub-assembly.

    NOTICE:
    When removing the injector assembly, store the injector assemblies in the correct order so that they can be returned to their original locations when reassembling.

  1. Remove the O-ring from each injector assembly.


73. REMOVE NOZZLE HOLDER GASKET

  1. A344926
    Remove the 4 nozzle holder gaskets from the cylinder head cover sub-assembly.


74. REMOVE CAMSHAFT POSITION SENSOR

  1. A398603
    Disconnect the camshaft position sensor connector.

  1. Remove the bolt and camshaft position sensor from the cylinder head cover sub-assembly.


75. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A339580
    Remove the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and cylinder head cover sub-assembly from the cylinder head sub-assembly.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut
    V100137
    Nozzle Holder Clamp Seat

  1. A339581E01
    Remove the cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets from the cylinder head cover sub-assembly.
    Text in Illustration 
    *1
    Cylinder Head Cover Gasket
    *2
    No. 2 Cylinder Head Cover Gasket
    *3
    Camshaft Bearing Cap Oil Hole Gasket


76. REMOVE ENGINE OIL LEVEL SENSOR
  1. Disconnect the engine oil level sensor connector.

  1. A388344
    Remove the 4 bolts and engine oil level sensor from the oil pan sub-assembly.


77. REMOVE OIL PAN SUB-ASSEMBLY

  1. A388358
    Remove the 2 nuts and 23 bolts.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

  1. A120816
    Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut off the applied sealer and remove the oil pan sub-assembly.

    NOTICE:
    1. Be careful not to damage the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.
    2. Be careful not to damage the cylinder block sub-assembly flange.


78. SET NO. 1 CYLINDER TO TDC/COMPRESSION
  1. Temporarily install the crankshaft pulley and crankshaft pulley set bolt to the crankshaft.

  1. A347371E01
    Align the timing mark of the crankshaft pulley and timing chain cover sub-assembly by rotating the crankshaft clockwise.
    Text in Illustration 
    *a
    Timing Mark

  1. Make sure that the timing mark of the camshaft timing sprocket is at the top.

    HINT:
    If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/compression).


79. REMOVE FAN PULLEY

  1. A341235
    Remove the 8 bolts, engine water pump assembly and gasket from the timing chain case assembly.


80. REMOVE ENGINE WATER PUMP ASSEMBLY

  1. A341235
    Remove the 8 bolts, engine water pump assembly and gasket from the timing chain case assembly.


81. REMOVE TIMING CHAIN COVER PLATE

A344936
  1. Remove the 3 bolts and timing chain cover plate.

  1. Remove the gasket.


82. REMOVE SUPPLY PUMP ASSEMBLY

NOTICE:
A354097
Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.

  1. A343530E01
    Using SST, hold the crankshaft pulley and loosen the supply pump shaft nut.
    SST
    09213-58014   (91551-80840)
    09330-00021  
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    NOTICE:
    Do not excessively loosen the supply pump shaft nut, otherwise SST cannot be installed.

    HINT:
    Rotate the supply pump shaft nut once to loosen it.

  1. A344938E01
    Install SST to the timing chain cover sub-assembly with the 3 bolts.
    SST
    09241-11010  

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    1. Make sure that the installation direction of SST is as shown in the illustration.

    2. A347063E01
      Align the hexagonal portion of SST with the supply pump shaft nut to install SST.

    Text in Illustration 
    *a
    Engine Front Side
    *b
    Engine Rear Side
    *c
    Hexagonal Portion

  1. A347305
    Remove the 2 bolts and No. 1 fuel pump bracket from the cylinder block sub-assembly and supply pump assembly.

  1. A354060
    Loosen the 3 nuts to the ends of the stud bolts.

    NOTICE:
    Do not completely remove the nuts. Otherwise, the supply pump assembly may fall off.

  1. A343532E01
    Using SST, loosen the supply pump shaft nut and detach the supply pump assembly and injection pump drive gear.

  1. Remove the 3 nuts from the stud bolts.

  1. Remove the O-ring from the supply pump assembly.

  1. Remove SST from the timing chain cover sub-assembly.

  1. A343534
    Remove the supply pump shaft nut from the timing chain cover sub-assembly service hole.

  1. Remove the crankshaft pulley set bolt and crankshaft pulley from the crankshaft.


83. REMOVE INJECTION PUMP INSULATOR

  1. A343533
    Remove the injection pump insulator from the cylinder block sub-assembly.


84. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A339584
    Remove the 20 bolts from the timing chain cover sub-assembly.

  1. Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.

    A339585E01

    Text in Illustration 
    *a
    Protective Tape
    -
    -

    NOTICE:
    Do not damage the contacting surfaces of the timing chain cover sub-assembly and timing chain case assembly.

  1. A339592
    Remove the timing chain case gasket from the timing chain case assembly.


85. REMOVE FRONT CRANKSHAFT OIL SEAL

  1. A339586E01
    Using a screwdriver and wooden block, pull out the front crankshaft oil seal.
    Text in Illustration 
    *a
    Protective Tape
    *b
    Wooden Block

    NOTICE:
    Do not damage the surface of the front crankshaft oil seal press fit hole.


86. INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR

  1. A339596
    Using a dial indicator, measure the backlash.

    Standard gear backlash:
    0.02 to 0.3 mm (0.000787 to 0.0118 in.)

    Maximum gear backlash:
    0.42 mm (0.0165 in.)

    If the gear backlash is more than the maximum, replace the timing chain case assembly or oil pump drive gear.


87. REMOVE OIL PUMP DRIVE GEAR

  1. A339595
    Remove the oil pump drive gear from the crankshaft.


88. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. When the pin is removed from the No. 3 chain tensioner assembly, the plunger and 2 springs may come off of the No. 3 chain tensioner assembly body, but this is not a malfunction.

  2. A347346E01
    Before installing the plunger and 2 springs to the No. 3 chain tensioner assembly body, check that they are free of foreign matter and not damaged.

Text in Illustration 
*a
No. 3 Chain Tensioner Assembly Body
*b
Spring
*c
Plunger

  1. A347347E01
    Fully insert the plunger, align the No. 3 chain tensioner assembly body hole with the plunger groove and insert the pin as shown in the illustration.
    Text in Illustration 
    *a
    Pin
    *b
    Plunger
    *c
    Plunger Groove

  1. A347348
    Remove the 2 bolts, No. 3 chain tensioner assembly and gasket from the engine balancer assembly.


89. REMOVE NO. 1 BALANCE SHAFT THRUST PLATE

  1. A347349
    Remove the bolt and No. 1 balance shaft thrust plate from the balance shaft gear sub-assembly.


90. REMOVE BALANCE SHAFT TIMING SPROCKET, BALANCE SHAFT GEAR SUB-ASSEMBLY AND NO. 3 CHAIN SUB-ASSEMBLY

  1. A347350
    Remove the balance shaft timing sprocket, balance shaft gear sub-assembly with No. 3 chain sub-assembly from the crankshaft and engine balancer assembly.


91. REMOVE TIMING CHAIN GUIDE

  1. A345766
    Remove the bolt and timing chain guide from the cylinder head sub-assembly.


92. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A343536E01
    Allow the plunger to extend slightly, and then rotate the stopper plate clockwise to release the lock. Once the lock is released, push the plunger into the No. 2 chain tensioner assembly.
    Text in Illustration 
    *a
    Stopper Plate
    *b
    Plunger

  1. A343537E01
    Move the stopper plate counter clockwise to set the lock, and then insert a pin into the stopper plate hole.
    Text in Illustration 
    *a
    Pin

  1. A343538
    Remove the 2 bolts and No. 2 chain tensioner assembly from the timing chain case assembly.


93. REMOVE NO. 2 CHAIN TENSIONER SLIPPER

  1. A343539
    Remove the bolt and No. 2 chain tensioner slipper from the timing chain case assembly.


94. REMOVE NO. 2 CHAIN VIBRATION DAMPER

  1. A343540
    Remove the 2 bolts and No. 2 chain vibration damper from the timing chain case assembly.


95. REMOVE NO. 2 CHAIN SUB-ASSEMBLY
  1. Remove the No. 2 chain sub-assembly from the camshaft timing sprockets and injection pump drive gear.


96. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. When the pin is removed from the No. 1 chain tensioner assembly, the plunger and spring may come off of the No. 1 chain tensioner assembly body, but this is not a malfunction.

  2. A347238E01
    Before installing the plunger and spring to the No. 1 chain tensioner assembly body, check that they are free of foreign matter and not damaged.

Text in Illustration 
*a
No. 1 Chain Tensioner Assembly Body
*b
Spring
*c
Plunger

  1. A343541E01
    Fully insert the plunger, align the No. 1 chain tensioner assembly body hole with the plunger groove and insert the pin as shown in the illustration.
    Text in Illustration 
    *a
    Pin
    *b
    Plunger
    *c
    Plunger Groove

  1. Remove the 2 bolts, No. 1 chain tensioner assembly and gasket from the cylinder block sub-assembly.


97. REMOVE NO. 1 CHAIN TENSIONER SLIPPER

  1. A343543
    Remove the No. 1 chain tensioner slipper from the straight pin.


98. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A343544
    Remove the bolt and No. 1 chain vibration damper from the cylinder block sub-assembly.


99. REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

  1. A343545
    Remove the crankshaft timing sprocket, injection pump drive gear with No. 1 chain sub-assembly from the crankshaft and supply pump shaft.


100. REMOVE CAMSHAFT TIMING SPROCKET

  1. for Exhaust Side:

    1. A343546E01
      Hold the hexagonal portion of the No. 2 camshaft with a wrench and remove the camshaft timing sprocket bolt and camshaft timing sprocket from the No. 2 camshaft.
      Text in Illustration 
      *a
      Hold
      V100135
      Turn

      NOTICE:
      Be careful not to damage the No. 2 camshaft or cylinder head sub-assembly with the wrench.

  1. for Intake Side:

    1. A343547E01
      Hold the hexagonal portion of the camshaft with a wrench and remove the camshaft timing sprocket bolt and camshaft timing sprocket from the camshaft.
      Text in Illustration 
      *a
      Hold
      V100135
      Turn

      NOTICE:
      Be careful not to damage the camshaft or cylinder head sub-assembly with the wrench.


101. REMOVE TIMING CHAIN CASE ASSEMBLY

  1. A339590
    Remove the 15 bolts from the timing chain case assembly.

  1. Using a screwdriver wrapped in protective tape, remove the timing chain case assembly by prying the points in the illustration.

    A339591E01

    Text in Illustration 
    *a
    Protective Tape
    -
    -

    NOTICE:
    Do not damage the contacting surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.

  1. A339593
    Remove the 4 O-rings from the cylinder head sub-assembly and cylinder block sub-assembly.

  1. A388469
    Remove the No. 2 water pump gasket from the timing chain case assembly.

← COMPONENTS (from Jan 2017)INSTALLATION (from Jan 2017) →