2014-2019 Hiace · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Jan 2017


INSPECT NO. 1 CHAIN SUB-ASSEMBLY

  1. A345790E01
    Using a spring scale, pull the No. 1 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.
    Text in Illustration 
    *a
    Measuring Point

  1. Using a vernier caliper, measure the length of 16 pins.

    Maximum chain elongation:
    144.7 mm (5.70 in.)

    HINT:
    Perform the measurement at 3 random places.

    If the elongation is more than the maximum, replace the No. 1 chain sub-assembly.


INSPECT NO. 2 CHAIN SUB-ASSEMBLY

  1. A345791E01
    Using a spring scale, pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.
    Text in Illustration 
    *a
    Measuring Point

  1. Using a vernier caliper, measure the length of 16 pins.

    Maximum chain elongation:
    121.6 mm (4.79 in.)

    HINT:
    Perform the measurement at 3 random places.

    If the elongation is more than the maximum, replace the No. 2 chain sub-assembly.


INSPECT NO. 3 CHAIN SUB-ASSEMBLY

  1. A347352E01
    Using a spring scale, pull the No. 3 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.
    Text in Illustration 
    *a
    Measuring Point

  1. Using a vernier caliper, measure the length of 16 pins.

    Maximum chain elongation:
    121.6 mm (4.79 in.)

    HINT:
    Perform the measurement at 3 random places.

    If the elongation is more than the maximum, replace the No. 3 chain sub-assembly.


INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. When the pin is removed from the No. 1 chain tensioner assembly, the plunger and spring may come off of the No. 1 chain tensioner assembly body, but this is not a malfunction.

  2. A347238E01
    Before installing the plunger and spring to the No. 1 chain tensioner assembly body, check that they are free of foreign matter and not damaged.

Text in Illustration 
*a
No. 1 Chain Tensioner Assembly Body
*b
Spring
*c
Plunger

  1. A346658E01
    Push the plunger and check that it moves smoothly.
    Text in Illustration 
    *a
    Plunger
    If necessary, replace the No. 1 chain tensioner assembly.


INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A345792E01
    Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.
    Text in Illustration 
    *a
    Stopper Plate
    *b
    Plunger
    If necessary, replace the No. 2 chain tensioner assembly.


INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. When the pin is removed from the No. 3 chain tensioner assembly, the plunger and 2 springs may come off of the No. 3 chain tensioner assembly body, but this is not a malfunction.

  2. A347346E01
    Before installing the plunger and 2 springs to the No. 3 chain tensioner assembly body, check that they are free of foreign matter and not damaged.

Text in Illustration 
*a
No. 3 Chain Tensioner Assembly Body
*b
Spring
*c
Plunger

  1. A347353E01
    Push the plunger and check that it moves smoothly.
    Text in Illustration 
    *a
    Plunger
    If necessary, replace the No. 3 chain tensioner assembly.


INSPECT CAMSHAFT TIMING SPROCKET
  1. Wrap the No. 2 chain sub-assembly around the camshaft timing sprocket.

  1. A345793
    Using a vernier caliper, measure the camshaft timing sprocket diameter with the No. 2 chain sub-assembly.

    Minimum sprocket with chain diameter:
    97.79 mm (3.85 in.)

    If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and camshaft timing sprocket.

    HINT:
    The vernier caliper must contact the No. 2 chain sub-assembly rollers for the measurement.


INSPECT CRANKSHAFT TIMING SPROCKET
  1. Wrap the No. 1 chain sub-assembly around the crankshaft timing sprocket.

  1. A345794
    Using a vernier caliper, measure the crankshaft timing sprocket diameter with the No. 1 chain sub-assembly.

    Minimum sprocket with chain diameter:
    71.26 mm (2.81 in.)

    If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and crankshaft timing sprocket.

    HINT:
    The vernier caliper must contact the No. 1 chain sub-assembly rollers for the measurement.


INSPECT INJECTION PUMP DRIVE GEAR

  1. for No. 1 Chain Sub-assembly Side:

    1. Wrap the No. 1 chain sub-assembly around the injection pump drive gear.

    2. A345796
      Using a vernier caliper, measure the injection pump drive gear diameter with the No. 1 chain sub-assembly.

      Minimum gear with chain diameter:
      71.26 mm (2.81 in.)

      If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and injection pump drive gear.

      HINT:
      The vernier caliper must contact the No. 1 chain sub-assembly rollers for the measurement.

  1. for No. 2 Chain Sub-assembly Side:

    1. Wrap the No. 2 chain sub-assembly around the injection pump drive gear.

    2. A345795
      Using a vernier caliper, measure the injection pump drive gear diameter with the No. 2 chain sub-assembly.

      Minimum gear with chain diameter:
      52.32 mm (2.06 in.)

      If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and injection pump drive gear.

      HINT:
      The vernier caliper must contact the No. 2 chain sub-assembly rollers for the measurement.


INSPECT BALANCE SHAFT TIMING SPROCKET
  1. Wrap the No. 3 chain sub-assembly around the balance shaft timing sprocket.

  1. A347354
    Using a vernier caliper, measure the balance shaft timing sprocket diameter with the No. 3 chain sub-assembly.

    Minimum sprocket with chain diameter:
    86.72 mm (3.41 in.)

    If the diameter is less than the minimum, replace the No. 3 chain sub-assembly and balance shaft timing sprocket.

    HINT:
    The vernier caliper must contact the No. 3 chain sub-assembly rollers for the measurement.


INSPECT BALANCE SHAFT GEAR SUB-ASSEMBLY
  1. Wrap the No. 3 chain sub-assembly around the balance shaft gear sub-assembly.

  1. A347355
    Using a vernier caliper, measure the balance shaft gear sub-assembly diameter with the No. 3 chain sub-assembly.

    Minimum sprocket with chain diameter:
    57.34 mm (2.26 in.)

    If the diameter is less than the minimum, replace the No. 3 chain sub-assembly and balance shaft gear sub-assembly.

    HINT:
    The vernier caliper must contact the No. 3 chain sub-assembly rollers for the measurement.


INSPECT NO. 1 CHAIN TENSIONER SLIPPER

  1. A345797E01
    Measure the depth of wear of the No. 1 chain tensioner slipper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *a
    Depth
    If the depth is more than the maximum, replace the No. 1 chain tensioner slipper.


INSPECT NO. 2 CHAIN TENSIONER SLIPPER

  1. A345798E01
    Measure the depth of wear of the No. 2 chain tensioner slipper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *a
    Depth
    If the depth is more than the maximum, replace the No. 2 chain tensioner slipper.


INSPECT NO. 1 CHAIN VIBRATION DAMPER

  1. A345799E01
    Measure the depth of wear of the No. 1 chain vibration damper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *a
    Depth
    If the depth is more than the maximum, replace the No. 1 chain vibration damper.


INSPECT NO. 2 CHAIN VIBRATION DAMPER

  1. A345800E01
    Measure the depth of wear of the No. 2 chain vibration damper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *a
    Depth
    If the depth is more than the maximum, replace the No. 2 chain vibration damper.


INSPECT TIMING CHAIN GUIDE

  1. A343586E01
    Measure the depth of wear of the timing chain guide.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *a
    Depth
    If the depth is more than the maximum, replace the timing chain guide.


INSPECT INTAKE MANIFOLD

  1. A345801
    Using a precision straightedge and feeler gauge, measure the warpage of the surface where the intake manifold contacts the cylinder head sub-assembly.

    Maximum warpage:
    0.10 mm (0.00394 in.)

    If the warpage is more than the maximum, replace the intake manifold.


INSPECT EXHAUST MANIFOLD

  1. A345802
    Using a precision straightedge and feeler gauge, measure the warpage of the surface where the exhaust manifold contacts the cylinder head sub-assembly.

    Maximum warpage:
    0.10 mm (0.00394 in.)

    If the warpage is more than the maximum, replace the exhaust manifold.


INSPECT CAMSHAFT
  1. Inspect the camshaft runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.00118 in.)

      If the circle runout is more than the maximum, replace the camshaft.

      HINT:
      Check the oil clearance after replacing the camshaft.

  1. Inspect the cam lobes.

    1. Using a micrometer, measure the cam lobe height.

      Standard cam lobe height:
      41.425 to 41.525 mm (1.631 to 1.635 in.)

      Minimum cam lobe height:
      41.375 mm (1.629 in.)

      If the cam lobe height is less than the minimum, replace the camshaft.

  1. Inspect the camshaft journals.

    1. Using a micrometer, measure the journal diameter.

      Standard Journal Diameter:
      Item
      Specified Condition
      No. 1 journal
      34.449 to 34.465 mm (1.356 to 1.357 in.)
      Other journals
      22.990 to 23.007 mm (0.905 to 0.906 in.)

      If the journal diameter is not as specified, check the oil clearance.


INSPECT NO. 2 CAMSHAFT
  1. Inspect the No. 2 camshaft runout.

    1. Place the No. 2 camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.00118 in.)

      If the circle runout is more than the maximum, replace the No. 2 camshaft.

      HINT:
      Check the oil clearance after replacing the No. 2 camshaft.

  1. Inspect the cam lobes.

    1. Using a micrometer, measure the cam lobe height.

      Standard cam lobe height:
      41.694 to 41.794 mm (1.641 to 1.645 in.)

      Minimum cam lobe height:
      41.644 mm (1.640 in.)

      If the cam lobe height is less than the minimum, replace the No. 2 camshaft.

  1. Inspect the No. 2 camshaft journals.

    1. Using a micrometer, measure the journal diameter.

      Standard Journal Diameter:
      Item
      Specified Condition
      No. 1 journal
      34.449 to 34.465 mm (1.356 to 1.357 in.)
      Other journals
      22.990 to 23.007 mm (0.905 to 0.906 in.)

      If the journal diameter is not as specified, check the oil clearance.


INSPECT CAMSHAFT OIL CLEARANCE
  1. Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing caps, camshaft journals and No. 2 camshaft journals.

  1. Place the camshaft and No. 2 camshaft on the cylinder head sub-assembly.

  1. A347311E01
    Lay a strip of Plastigage across each of the camshaft journals.
    Text in Illustration 
    *a
    Plastigage

  1. Install the No. 1 camshaft bearing cap and No. 2 camshaft bearing caps to the cylinder head sub-assembly (Click here).

    NOTICE:
    Do not turn the camshaft and No. 2 camshaft.

  1. Remove the No. 1 camshaft bearing cap and No. 2 camshaft bearing caps from the cylinder head sub-assembly (Click here).

  1. A347310
    Measure the Plastigage at its widest point.

    Standard Oil Clearance:
    Item
    Specified Condition
    No. 1 journal
    0.040 to 0.077 mm (0.00157 to 0.00303 in.)
    Other journals
    0.025 to 0.062 mm (0.000984 to 0.00244 in.)

    Maximum Oil Clearance:
    Item
    Specified Condition
    No. 1 journal
    0.117 mm (0.00461 in.)
    Other journals
    0.102 mm (0.00402 in.)

    If the camshaft oil clearance is more than the maximum, replace the camshaft. If necessary, replace the cylinder head sub-assembly.

  1. Completely remove the Plastigage from the camshaft journals.


INSPECT CYLINDER HEAD SET BOLT

  1. w/ Washer:

    1. A345806E01
      Using a vernier caliper, measure the thread outside diameter of the cylinder head set bolt.

      Minimum diameter:
      11.4 mm (0.449 in.)

      Text in Illustration 
      *a
      Measuring Area
      *b
      Washer
      If the diameter is less than the minimum, replace the cylinder head set bolt.

  1. w/o Washer:

    1. A345805E01
      Using a vernier caliper, measure the thread outside diameter of the cylinder head set bolt.

      Minimum diameter:
      12.8 mm (0.504 in.)

      Text in Illustration 
      *a
      Measuring Area
      If the diameter is less than the minimum, replace the cylinder head set bolt and cylinder head set bolt spacer.


INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Turn the roller by hand and check that it turns smoothly.
    If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.


INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
  1. Keep the adjuster free from dirt and foreign matter.
  2. Use only clean engine oil.

  1. Place the valve lash adjuster assembly into a container full of new engine oil.

    A345808E01

    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT
    *c
    Taper Part
    *d
    Plunger
    *e
    Low Pressure Chamber
    *f
    Check Ball
    *g
    High Pressure Chamber
    -
    -

  1. Insert the tip of SST into the plunger and use the tip to press down on the check ball inside the plunger.

    SST
    09276-75010  

  1. Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.

  1. After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

    OK:
    Plunger is very difficult to move.

    If the result is not as specified, replace the valve lash adjuster assembly.


INSPECT ENGINE BALANCER ASSEMBLY

  1. Inspect the balance shaft thrust clearance.

    1. A347356
      Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.

      Standard thrust clearance:
      0.05 to 0.09 mm (0.00197 to 0.00354 in.)

      Maximum thrust clearance:
      0.09 mm (0.00354 in.)

      If the thrust clearance is more than the maximum, replace the engine balancer assembly.

  1. Inspect the balance shaft thrust backlash.

    1. A347357E01
      Fix the No. 2 balance shaft in place, and then, using a dial indicator, measure the backlash of the No. 1 and No. 2 balance shafts as shown in the illustration.

      Standard backlash:
      0.01 to 0.12 mm (0.000394 to 0.00472 in.)

      Maximum backlash:
      0.12 mm (0.00472 in.)

      Text in Illustration 
      *a
      No. 2 Balance Shaft Side
      *b
      No. 1 Balance Shaft Side
      *c
      Fix
      If the backlash is more than the maximum, replace the engine balancer assembly.

← DISASSEMBLY (from Jan 2017)REASSEMBLY (from Jan 2017) →