2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jan 2017


1. REMOVE ENGINE ASSEMBLY
(Click here)

2. REMOVE DIFFERENTIAL PRESSURE SENSOR

  1. A396478
    Disconnect the connector from the differential pressure sensor.

  1. Remove the bolt and differential pressure sensor from the pipe clamp.

  1. A396479
    Slide the 2 clamps and disconnect the 2 air hoses from the No. 1 vacuum pipe and No. 2 vacuum pipe.

  1. A352099
    Slide the 2 clamps and remove the 2 air hoses from the differential pressure sensor.


3. REMOVE EXHAUST GAS TEMPERATURE SENSOR

CAUTION:
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

  1. A396505
    Disconnect the 3 connectors from the 3 exhaust gas temperature sensors.

  1. A396506
    Remove the nut and disconnect the No. 3 exhaust gas temperature sensor from the No. 1 vacuum pipe.

  1. A396507
    Remove the bolt and open the clamp of the pipe clamp.

  1. Detach the 3 connectors from the pipe clamp.

  1. A396508
    Using a 14 mm union nut wrench, remove the exhaust gas temperature sensor from the exhaust manifold converter sub-assembly.

  1. A396509
    Using a 14 mm union nut wrench, remove the No. 2 exhaust gas temperature sensor from the exhaust manifold converter sub-assembly.

  1. A396510
    Using a 14 mm union nut wrench, remove the No. 3 exhaust gas temperature sensor from the exhaust manifold converter sub-assembly.


4. REMOVE NO. 1 VACUUM PIPE

  1. A396492
    Remove the nut and clamp from the No. 1 vacuum pipe and No. 2 vacuum pipe.

  1. A396493
    Using a 17 mm union nut wrench, remove the No. 1 vacuum pipe from the exhaust manifold converter sub-assembly.


5. REMOVE NO. 2 VACUUM PIPE

  1. A396494
    Using a 17 mm union nut wrench, remove the No. 2 vacuum pipe from the exhaust manifold converter sub-assembly.

  1. A396495
    Remove the clamp from the pipe clamp.


6. REMOVE PIPE CLAMP

  1. A396496
    Remove the 3 bolts and pipe clamp from the engine cover bracket.


7. REMOVE ENGINE COVER BRACKET

  1. A405484E01
    Remove the bolt and disconnect the engine wire from the engine cover bracket.

  1. A396497
    Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.


8. REMOVE AIR FUEL RATIO SENSOR

CAUTION:
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

  1. A398612E01
    Disconnect the connector.

  1. Using SST, remove the air fuel ratio sensor.

    SST
    09224-00012  


9. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A396498
    Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.


10. REMOVE NO. 1 TURBO INSULATOR

  1. A396499
    Remove the 3 bolts and No. 1 turbo insulator from the exhaust manifold and turbocharger sub-assembly.


11. REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY

  1. A396500
    Remove the bolt, 2 nuts and No. 2 exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.


12. REMOVE EXHAUST PIPE SUPPORT STAY

  1. A396501
    Remove the 3 bolts and exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.


13. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

  1. A396502
    Remove the nut, exhaust pipe clamp and exhaust manifold converter sub-assembly from the turbocharger sub-assembly.

  1. Remove the gasket.

← COMPONENTS (from Jan 2017)INSTALLATION (from Jan 2017) →