2014-2019 Hiace · Service Manual SUSPENSION & AXLE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Oct 2014


REMOVE REAR WHEEL

REMOVE REAR BRAKE DRUM SUB-ASSEMBLY

  1. Release the parking brake lever, and remove the brake drum.

    C263541E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

    HINT:
    If the brake drum cannot be removed easily, perform the following steps.

  1. Remove the hole plug and insert a screwdriver through the hole in the backing plate, and hold the automatic adjusting lever away from the adjuster.

  1. Using another screwdriver, contract the brake shoe adjuster by turning the adjusting wheel.


INSPECT REAR AXLE SHAFT BEARING LOOSENESS

  1. C357267
    Using a dial indicator, check for looseness near the center of the rear axle shaft.

    Maximum:
    0.7 mm (0.0275 in.)

    NOTICE:
    Ensure that the dial indicator is set at right angles to the measurement surface.

    If looseness exceeds the maximum, replace the rear axle shaft bearing.


INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

ADJUST REAR DRUM BRAKE SHOE CLEARANCE

  1. Using a screwdriver from a service hole, turn the adjuster to expand the shoes so that the brake shoes touch the brake drum.

    C263542E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Using another screwdriver, push up the automatic adjust lever and turn the adjuster to contract the shoes so that the brake shoe does not touch the brake drum. Then turn the adjuster another 180 degrees to further contract the shoes.

    C263541E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Install the hole plug.


INSTALL REAR WHEEL

Torque:
100 N*m{ 1020 kgf*cm , 74 ft.*lbf }


INSPECT PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Pull firmly on the parking brake control handle.

  1. Release the parking brake lock, and return the parking brake control handle to its off position.

  1. Slowly pull the parking brake control handle all the way up, and count the number of clicks.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
    12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)

    HINT:
    1. If the number of clicks falls outside of the specified range, release the parking brake lock and adjust it.
    2. If there are fewer clicks than the specified value, loosen the parking brake wire adjustment nut an the lock nut. With the parking brake cable loosened, adjust the clearance between the brake drum and lining.


ADJUST PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Lift the vehicle

  1. C102142E01
    Depress the parking brake handle. Hold the parking brake adjusting nut using a wrench, and loosen the lock nut.

  1. Turn the parking brake adjusting nut until the parking brake handle travel meets the above specification.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
    12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)

  1. Count the number of clicks after depressing and releasing the parking brake control handle 3 or 4 times.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake control handle, check that the parking brake indicator light comes on.

    Standard:
    Brake warning light always comes on at the first click.

  1. Hold the parking brake adjusting nut using a wrench, and tighten the lock nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }

  1. Lower the vehicle.

← COMPONENTS (from Oct 2014)REMOVAL (from Oct 2014) →