The combination meter assembly uses the fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. The Hall IC built into the fuel sender gauge assembly changes the output voltage according to the amount of fuel remaining. The combination meter assembly receives fuel injection volume signals from the ECM and detects the voltage output from the fuel sender gauge assembly and operates the fuel receiver gauge.
Be careful of flames.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Check if DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
DTCs are not output.
| Proceed to |
|---|
| OK (for 7GR-FKS) |
| OK (for 1GD-FTV) |
| NG |
OK (for 7GR-FKS)
OK (for 1GD-FTV)
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Check if SFI system DTCs are output.
Click hereEngine / Hybrid System>7GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the Active Test.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Fuel Gauge Operation (Sender E) | Fuel receiver gauge (Sender E) | ON | See [Display] |
| Fuel Gauge Operation (Empty) | Fuel receiver gauge (Empty) | ON | See [Display] |
| Fuel Gauge Operation (Warning) | Fuel receiver gauge (Warning) | ON | See [Display] |
| Fuel Gauge Operation (1/4) | Fuel receiver gauge (1/4) | ON | See [Display] |
| Fuel Gauge Operation (1/2) | Fuel receiver gauge (1/2) | ON | See [Display] |
| Fuel Gauge Operation (3/4) | Fuel receiver gauge (3/4) | ON | See [Display] |
| Fuel Gauge Operation (Full) | Fuel receiver gauge (Full) | ON | See [Display] |
| Fuel Gauge Operation (Sender F) | Fuel receiver gauge (Sender F) | ON | See [Display] |
| Tester Display |
|---|
| Fuel Gauge Operation (Sender E) |
| Tester Display |
|---|
| Fuel Gauge Operation (Empty) |
| Tester Display |
|---|
| Fuel Gauge Operation (Warning) |
| Tester Display |
|---|
| Fuel Gauge Operation (1/4) |
| Tester Display |
|---|
| Fuel Gauge Operation (1/2) |
| Tester Display |
|---|
| Fuel Gauge Operation (3/4) |
| Tester Display |
|---|
| Fuel Gauge Operation (Full) |
| Tester Display |
|---|
| Fuel Gauge Operation (Sender F) |
| *a | Fuel Gauge Operation (Sender E) |
| *b | Fuel Gauge Operation (Empty) |
| *c | Fuel Gauge Operation (Warning) |
| *d | Fuel Gauge Operation (1/4) |
| *e | Fuel Gauge Operation (1/2) |
| *f | Fuel Gauge Operation (3/4) |
| *g | Fuel Gauge Operation (Full) |
| *h | Fuel Gauge Operation (Sender F) |
[Display]: Fuel receiver gauge (for Multi-information Display Type)
| *a | Fuel Gauge Operation (Sender E) |
| *b | Fuel Gauge Operation (Empty) |
| *c | Fuel Gauge Operation (Warning) |
| *d | Fuel Gauge Operation (1/4) |
| *e | Fuel Gauge Operation (1/2) |
| *f | Fuel Gauge Operation (3/4) |
| *g | Fuel Gauge Operation (Full) |
| *h | Fuel Gauge Operation (Sender F) |
[Display]: Fuel receiver gauge (for Segment Display Type)
Fuel receiver gauge indication is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the X6 fuel suction with pump and gauge tube assembly connector.
Disconnect the N22 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X6-3 (FR) - N22-31 (FR) | Always | Below 1 Ω |
| X6-2 (FE) - N22-24 (FF&B) | Always | Below 1 Ω |
| X6-1 (FV) - N22-14 (FV) | Always | Below 1 Ω |
| X6-3 (FR) or N22-31 (FR) - Other terminals and body ground | Always | 10 kΩ or higher |
| X6-2 (FE) or N22-24 (FF&B) - Other terminals and body ground | Always | 10 kΩ or higher |
| X6-1 (FV) or N22-14 (FV) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fuel sender gauge assembly.
Click hereEngine / Hybrid System>7GR-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Inspect the fuel sender gauge assembly.
Click hereEngine / Hybrid System>7GR-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Fuel Suction with Pump and Gauge Tube Assembly) |
Remove fuel suction with pump and gauge tube assembly.
Click hereEngine / Hybrid System>7GR-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (FV) - B-3 | Always | Below 1 Ω |
| A-2 (FE) - B-2 | Always | Below 1 Ω |
| A-3 (FR) - B-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if ECD system DTCs are output.
w/ DPF: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR
w/ Urea SCR System: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR
w/ EGR Cooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>DTC CHECK / CLEAR
w/o EGR Cooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>DTC CHECK / CLEAR
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ DPF: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
w/ Urea SCR System: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DIAGNOSTIC TROUBLE CODE CHART
w/ EGR Cooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>DIAGNOSTIC TROUBLE CODE CHART
w/o EGR Cooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>DIAGNOSTIC TROUBLE CODE CHART
Using the GTS, perform the Active Test.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range |
|---|---|---|
| Fuel Gauge Operation (Sender E) | Fuel receiver gauge (Sender E) | ON |
| Fuel Gauge Operation (Empty) | Fuel receiver gauge (Empty) | ON |
| Fuel Gauge Operation (Warning) | Fuel receiver gauge (Warning) | ON |
| Fuel Gauge Operation (1/4) | Fuel receiver gauge (1/4) | ON |
| Fuel Gauge Operation (1/2) | Fuel receiver gauge (1/2) | ON |
| Fuel Gauge Operation (3/4) | Fuel receiver gauge (3/4) | ON |
| Fuel Gauge Operation (Full) | Fuel receiver gauge (Full) | ON |
| Fuel Gauge Operation (Sender F) | Fuel receiver gauge (Sender F) | ON |
| Tester Display |
|---|
| Fuel Gauge Operation (Sender E) |
| Tester Display |
|---|
| Fuel Gauge Operation (Empty) |
| Tester Display |
|---|
| Fuel Gauge Operation (Warning) |
| Tester Display |
|---|
| Fuel Gauge Operation (1/4) |
| Tester Display |
|---|
| Fuel Gauge Operation (1/2) |
| Tester Display |
|---|
| Fuel Gauge Operation (3/4) |
| Tester Display |
|---|
| Fuel Gauge Operation (Full) |
| Tester Display |
|---|
| Fuel Gauge Operation (Sender F) |
| *a | Fuel Gauge Operation (Sender E) |
| *b | Fuel Gauge Operation (Empty) |
| *c | Fuel Gauge Operation (Warning) |
| *d | Fuel Gauge Operation (1/4) |
| *e | Fuel Gauge Operation (1/2) |
| *f | Fuel Gauge Operation (3/4) |
| *g | Fuel Gauge Operation (Full) |
| *h | Fuel Gauge Operation (Sender F) |
[Display]: Fuel receiver gauge (for Multi-information Display Type)
| *a | Fuel Gauge Operation (Sender E) |
| *b | Fuel Gauge Operation (Empty) |
| *c | Fuel Gauge Operation (Warning) |
| *d | Fuel Gauge Operation (1/4) |
| *e | Fuel Gauge Operation (1/2) |
| *f | Fuel Gauge Operation (3/4) |
| *g | Fuel Gauge Operation (Full) |
| *h | Fuel Gauge Operation (Sender F) |
[Display]: Fuel receiver gauge (for Segment Display Type)
Fuel receiver gauge indication is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the X6 fuel tank vent tube assembly connector.
Disconnect the N22 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X6-3 (FR) - N22-31 (FR) | Always | Below 1 Ω |
| X6-2 (FE) - N22-24 (FF&B) | Always | Below 1 Ω |
| X6-1 (FV) - N22-14 (FV) | Always | Below 1 Ω |
| X6-3 (FR) or N22-31 (FR) - Other terminals and body ground | Always | 10 kΩ or higher |
| X6-2 (FE) or N22-24 (FF&B) - Other terminals and body ground | Always | 10 kΩ or higher |
| X6-1 (FV) or N22-14 (FV) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fuel sender gauge assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Inspect the fuel sender gauge assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Fuel Tank Vent Tube Assembly) |
Remove the fuel tank vent tube assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (FV) - B-3 | Always | Below 1 Ω |
| A-2 (FE) - B-2 | Always | Below 1 Ω |
| A-3 (FR) - B-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG