The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel sender gauge assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
3.REMOVE REAR SEAT ASSEMBLY
for Van:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Van)>REMOVAL
for Folding Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>REMOVAL
for Commuter, 3-Passenger Seat with 2-Point Type Seat Belt:
for Commuter, 3-Passenger Seat with 3-Point Type Seat Belt:
for Commuter, 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, 4-Passenger Seat)>REMOVAL
for Commuter, Single-Passenger Seat with 2-Point Type Seat Belt:
for Commuter, Single-Passenger Seat with 3-Point Type Seat Belt:
for Commuter, 2-Passenger Seat with 3-Point Type Seat Belt:
for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt and Headrest:
for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest:
58759A
4.REMOVE FUEL TANK INSPECTION HOLE COVER
Fold back the rear floor carpet.
Remove the rear floor board.
Remove the 4 bolts and fuel tank inspection hole cover.
Disconnect the connector from the fuel vent tube assembly.
77285R
5.REMOVE NO. 1 FUEL TUBE CLAMP
77010
6.REMOVE FUEL TANK VENT TUBE ASSEMBLY
Remove the 2 tube joint clips and pull out the fuel tank main tube sub-assembly and fuel tank return tube from the fuel tank vent tube assembly.
| *a | Fuel Tube Joint |
| *b | Fuel Tube |
| *c | O-Ring |
| *d | Tube Joint Clip |
Remove any dirt and foreign matter on the fuel tube joint before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Perform this work by hand. Do not use any tools.
Do not forcibly bend or twist the nylon tube.
Protect the disconnected parts by covering them with plastic bags and tape after disconnecting the fuel tank main tube sub-assembly and fuel tank return tube.
Remove the fuel pump gauge retainer from the fuel tank assembly.
| *a | SST (Plate) |
| *b | SST (Claw) |
| *c | Insertion point |
|
SST (Bolt) |
Set the 2 claws, 2 bolts and plate of SST on the fuel pump gauge retainer.
Securely insert the ends of SST into the insertion points in the fuel pump gauge retainer.
While firmly pressing the claws of SST into the insertion points in the fuel pump gauge retainer, tighten the bolts of the claws.
Attach the handle of SST.
| *a | Insertion point |
Check once more that the tip of SST is securely inserted into the insertion area of the fuel pump gauge retainer as shown in the illustration.
While lightly pressing down on SST so it does not come off the fuel pump gauge retainer, slowly turn the handle and remove the fuel pump gauge retainer.
Do not use any tools other than SST, such as a screwdriver, etc.
Do not use excessive force when pressing down on SST, as the fuel pump gauge retainer will place excessive force on the fuel tank vent tube assembly and fuel pump gauge retainer and be difficult to remove, and parts may be damaged.
Be sure to keep the handle level when turning it, as SST may slip off the fuel pump gauge retainer if the handle is turned at an angle with excessive force.
Do not use an impact wrench or turn the handle with excessive force, as parts may be damaged.
If SST slips off the fuel pump gauge retainer, loosen the bolts and reattach SST to the fuel pump gauge retainer.
Remove the fuel tank vent tube assembly from the fuel tank sub-assembly.
Be careful not to bend the arm of the fuel sender gauge assembly.
Remove the fuel tank vent tube gasket from the fuel tank sub-assembly.
83320
7.REMOVE FUEL SENDER GAUGE ASSEMBLY
Disconnect the fuel sender gauge connector.
|
Slide |
Detach the 2 claws and slide the fuel sender gauge assembly upward to remove it.