Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2019.02–2019.06
RM35X0E _56 Audio / Visual / Telematics _078379 NAVIGATION / MULTI INFO DISPLAY _0380999 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the television camera assembly and the radio and display receiver assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the television camera assembly signal circuit
·

Harness or connector

·

Television camera assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E402604E17
1.583,2.979 2.781,3.385 1.198,0.406 10 false Radio and Display Receiver Assembly 1.583,2.813 1.969,3.01 0.385,0.198 10 false O7 2.135,2.5 2.74,2.74 0.604,0.24 10 false CSLD 2.083,2.083 2.635,2.292 0.552,0.208 10 false CGND 2.344,1.646 2.729,1.844 0.385,0.198 10 false V- 2.313,1.25 2.698,1.448 0.385,0.198 10 false V+ 2.229,0.823 2.615,1.021 0.385,0.198 10 false CA+ 2.615,0.719 3,0.917 0.385,0.198 10 false 30 2.604,1.563 2.99,1.76 0.385,0.198 10 false 29 2.604,1.135 2.99,1.333 0.385,0.198 10 false 28 2.615,1.979 3,2.177 0.385,0.198 10 false 27 2.604,2.406 2.99,2.604 0.385,0.198 10 false 26 5.469,2.823 5.854,3.021 0.385,0.198 10 false i7 5.448,3 6.604,3.365 1.156,0.365 10 false Television Camera Assembly 5.531,0.833 5.917,1.031 0.385,0.198 10 false CB+ 5.521,1.271 5.906,1.469 0.385,0.198 10 false CV+ 5.51,1.688 5.896,1.885 0.385,0.198 10 false CV- 5.51,2.104 6.104,2.375 0.594,0.271 10 false CGND 5.292,0.75 5.677,0.948 0.385,0.198 10 false 6 5.292,1.146 5.677,1.344 0.385,0.198 10 false 3 5.281,1.552 5.667,1.75 0.385,0.198 10 false 2 5.281,1.979 5.667,2.177 0.385,0.198 10 false 5 3.938,2.396 4.323,2.594 0.385,0.198 10 false * 0.198,3.354 1.042,3.563 0.844,0.208 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable was disconnected from and reconnected to the negative (-) battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point".

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION

·

The following malfunctions may occur if a radio and display receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio and display receiver assembly, be sure to replace it with new one.

-

Communication malfunction DTC is output

-

Does not operate normally




HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the i7 television camera assembly connector.


b.

Disconnect the O7 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i7-6 (CB+) - O7-30 (CA+) Always Below 1 Ω
i7-3 (CV+) - O7-28 (V+) Always Below 1 Ω
i7-2 (CV-) - O7-29 (V-) Always Below 1 Ω
i7-5 (CGND) - O7-27 (CGND) Always Below 1 Ω
i7-6 (CB+) or O7-30 (CA+) - Body ground Always 10 kΩ or higher
i7-3 (CV+) or O7-28 (V+) - Body ground Always 10 kΩ or higher
i7-2 (CV-) or O7-29 (V-) - Body ground Always 10 kΩ or higher
i7-5 (CGND) or O7-27 (CGND) - Body ground Always 10 kΩ or higher
O7-26 (CSLD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO AND DISPLAY ASSEMBLY (CA+, CGND, CSLD)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO AND DISPLAY ASSEMBLY (CA+, CGND, CSLD)
a.
E402607C06
1.583,0.156 1.969,0.458 0.385,0.302 0.583,1.646 0.771,1.646 0.771,1.646 0.969,1.24 true 0.969,1.844 1.156,1.844 1.156,1.844 1.417,1.25 true 1.115,2.052 1.302,2.052 1.302,2.052 1.542,1.229 true 1.698,0.229 2.156,0.427 0.458,0.198 10 false O7 0.24,0.135 0.698,0.333 0.458,0.198 10 false *a 0.25,1.542 0.708,1.74 0.458,0.198 10 false CA+ 0.542,1.75 1.052,1.948 0.51,0.198 10 false CGND 0.708,1.969 1.219,2.167 0.51,0.198 10 false CSLD
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O7-30 (CA+) - O7-27 (CGND) Ignition switch ACC 5.5 to 7.05 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-26 (CSLD) - Body ground Always Below 1 Ω
O7-27 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY ASSEMBLY

3.CHECK TELEVISION CAMERA ASSEMBLY
E402606C06
0.958,1.073 1.313,1.344 0.354,0.271 2.698,2.885 2.875,2.885 2.875,2.885 3.135,2.25 true 5,2.792 5.177,2.792 5.177,2.792 5.438,2.156 true 3.208,2.167 3.375,2.917 3.375,2.917 3.531,2.917 true 5.542,2.104 5.708,2.854 5.708,2.854 5.865,2.854 true 0.344,2.573 0.521,2.573 0.521,2.573 0.635,1.969 true 0.74,1.958 0.865,2.823 0.865,2.823 1.021,2.823 true 0.177,0.99 0.49,1.188 0.313,0.198 10 false *a 2.635,0.979 2.948,1.177 0.313,0.198 10 false *b 4.948,0.927 5.26,1.125 0.313,0.198 10 false *c 2.531,2.792 2.844,2.99 0.313,0.198 10 false *d 3.583,2.813 3.896,3.01 0.313,0.198 10 false *e 4.823,2.698 5.135,2.896 0.313,0.198 10 false *d 5.917,2.76 6.229,2.958 0.313,0.198 10 false *e 2.448,1.792 2.906,2.031 0.458,0.24 10 false GND 4.75,1.813 5.208,2.052 0.458,0.24 10 false GND 1.073,2.75 1.385,2.948 0.313,0.198 10 false V+ 0.135,2.479 0.448,2.677 0.313,0.198 10 false V- 1.063,1.125 1.375,1.323 0.313,0.198 10 false O7
*a Component with harness connected *b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -


a.

Remove the radio and display receiver assembly with the connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Check the waveform of the television camera assembly using an oscilloscope.

Item Content
Measurement terminal O7-28 (V+) - O7-29 (V-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift position in R, camera lens is not covered, displaying an image.
Waveform 2: Ignition switch ON, shift position in R, camera lens is covered, blacking out the screen.

HINT:
·

The video waveform changes according to the image sent by the rear camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.



OK:

Waveform is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG