The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.
Read the Data List according to the display on the GTS.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Lock Pos SW | Back door unlock detection switch signal | OFF or ON | OFF: Back door unlocked
ON: Back door locked |
- |
| FR Door Lock Pos | Front door RH unlock detection switch signal | UNLOCK or LOCK | UNLOCK: Front door RH unlocked
LOCK: Front door RH locked |
- |
| FL Door Lock Pos | Front door LH unlock detection switch signal | UNLOCK or LOCK | UNLOCK: Front door LH unlocked
LOCK: Front door LH locked |
- |
| RR-Door Lock Pos SW | Slide door RH unlock detection switch signal | OFF or ON | OFF: Slide door RH unlocked
ON: Slide door RH locked |
w/ Slide Door RH |
| RL-Door Lock Pos SW | Slide door LH unlock detection switch signal | OFF or ON | OFF: Slide door LH unlocked
ON: Slide door LH locked |
w/ Slide Door LH |
| Tester Display |
|---|
| Back Door Lock Pos SW |
| FR Door Lock Pos |
| FL Door Lock Pos |
| RR-Door Lock Pos SW |
| RL-Door Lock Pos SW |
Normal conditions listed above are displayed.
| Result | Proceed to |
|---|---|
| OK | A |
| NG ("FR Door Lock Pos" is abnormal) | B |
| NG ("FL Door Lock Pos" is abnormal) | C |
| NG ("RR-Door Lock Pos SW" is abnormal) (w/ Slide Door RH) | D |
| NG ("RL-Door Lock Pos SW" is abnormal) (w/ Slide Door LH) | E |
| NG ("Back Door Lock Pos SW" is abnormal) | F |
A
B
C
D
E
F
Remove the front door with motor lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door with motor lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R4 front door with motor lock assembly RH connector.
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R4-7 (LSSR) - 3B-12 | Always | Below 1 Ω |
| R4-8 (E) - Body ground | Always | Below 1 Ω |
| R4-7 (LSSR) or 3B-12 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-12 - A-17 (LSFR) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Remove the front door with motor lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door with motor lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R14 front door with motor lock assembly LH connector.
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R14-8 (LSSR) - 3B-13 | Always | Below 1 Ω |
| R14-7 (E) - Body ground | Always | Below 1 Ω |
| R14-8 (LSSR) or 3B-13 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-13 - A-19 (LSFL) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Remove the slide door lock remote control assembly RH.
Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (except Wagon)>REMOVAL
Inspect the slide door lock remote control assembly RH.
Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (except Wagon)>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/o Slide Door Control Junction RH) | A |
| OK (w/ Slide Door Control Junction RH) | B |
| NG | C |
A
B
C
Disconnect the U1 slide door lock remote control assembly RH connector.
Disconnect the N18 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U1-4 (LSSR) - N18-20 (LSWR) | Always | Below 1 Ω |
| U1-1 (E) - Body ground | Always | Below 1 Ω |
| U1-4 (LSSR) or N18-20 (LSWR) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Remove the slide door control junction female.
Click hereVehicle Interior>DOOR LOCK>DOOR LOCK JUNCTION>REMOVAL
Inspect the slide door control junction female.
Click hereVehicle Interior>DOOR LOCK>DOOR LOCK JUNCTION>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the slide door control junction male.
Click hereVehicle Interior>DOOR LOCK>DOOR LOCK JUNCTION>REMOVAL
Inspect the slide door control junction male.
Click hereVehicle Interior>DOOR LOCK>DOOR LOCK JUNCTION>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the W13 slide door control junction male connector.
Disconnect the N18 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W13-3 (LSSR) - N18-20 (LSWR) | Always | Below 1 Ω |
| W13-5 (E) - Body ground | Always | Below 1 Ω |
| W13-3 (LSSR) or N18-20 (LSWR) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Remove the slide door lock remote control assembly LH.
Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (except Wagon)>REMOVAL
Inspect the slide door lock remote control assembly LH.
Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (except Wagon)>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/o Slide Door Control Junction LH) | A |
| OK (w/ Slide Door Control Junction LH) | B |
| NG | C |
A
B
C
Disconnect the U5 slide door lock remote control assembly LH connector.
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U5-4 (LSSR) - 3B-14 | Always | Below 1 Ω |
| U5-1 (E) - Body ground | Always | Below 1 Ω |
| U5-4 (LSSR) or 3B-14 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-14 - A-5 (LSWL) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Remove the slide door control junction female.
Click hereVehicle Interior>DOOR LOCK>DOOR LOCK JUNCTION>REMOVAL
Inspect the slide door control junction female.
Click hereVehicle Interior>DOOR LOCK>DOOR LOCK JUNCTION>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the slide door control junction male.
Click hereVehicle Interior>DOOR LOCK>DOOR LOCK JUNCTION>REMOVAL
Inspect the slide door control junction male.
Click hereVehicle Interior>DOOR LOCK>DOOR LOCK JUNCTION>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the V15 slide door control junction male connector.
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V15-3 (LSSR) - 3B-14 | Always | Below 1 Ω |
| L4-5 (E) - Body ground | Always | Below 1 Ω |
| L4-3 (LSSR) or 3B-14 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-14 - A-5 (LSWL) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Remove the back door remote control assembly.
Inspect the back door remote control assembly.
Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the i8 back door remote control assembly connector.
Disconnect the N19 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| i8-1 (S) - N19-27 (LSWB) | Always | Below 1 Ω |
| i8-4 (E) - Body ground | Always | Below 1 Ω |
| i8-1 (S) or N19-27 (LSWB) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C