Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
71848P
1.REMOVE FRONT SEAT NO. 2 ADJUSTER COVER CAP RH
|
Remove in this Direction |
Remove the front seat No. 2 adjuster cover cap RH as shown in the illustration.
71848N
2.REMOVE FRONT SEAT NO. 1 ADJUSTER COVER CAP RH
|
Remove in this Direction |
Remove the front seat No. 1 adjuster cover cap RH as shown in the illustration.
72345L
3.REMOVE RECLINING CONNECTING PIPE RH
Remove the 2 reclining connecting pipes RH.
71139N
4.REMOVE FRONT SEAT INNER LEG COVER RH
Remove the clip.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull in the removal direction and detach the clip.
Detach the guide and remove the front seat inner leg cover RH.
71130B
5.REMOVE FRONT SEAT LEG ASSEMBLY RH
w/ Seat Belt Warning System:
Detach the claw and clamp.
w/ Front Seat Side Airbag:
Detach the claw and clamp.
|
Slide in this Direction |
Operate the seat track adjusting handle RH and move the front seat assembly RH to the frontmost position and detach the guide.
Remove the 5 nuts and front seat leg assembly RH.
72329D
6.REMOVE SEAT ADJUSTER BOLT COVER RH
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw and remove the seat adjuster bolt cover RH as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
72525M
7.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
Remove the screw.
Detach the guide and remove the reclining adjuster release handle RH.
71396K
8.REMOVE CENTER SEAT HINGE COVER LH
|
Remove in this Direction |
Using moulding remover A, detach the claw as shown in the illustration.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull in the removal direction and detach the clip.
|
Remove in this Direction |
Using moulding remover A, detach the claw and guide as shown in the illustration.
|
Remove in this Direction |
Detach the guide and remove the center seat hinge cover LH as shown in the illustration.
71811T
9.REMOVE FRONT SEAT CUSHION SHIELD RH
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull in the removal direction and detach the clip.
|
Remove in this Direction |
Using moulding remover A, detach the claw as shown in the illustration.
|
Remove in this Direction |
Using moulding remover A, detach the claw and guide as shown in the illustration.
|
Remove in this Direction |
Detach the guide and remove the front seat cushion shield RH as shown in the illustration.
73250
10.REMOVE FRONT CENTER SEAT BELT ASSEMBLY
Detach the hook.
w/ Center Seat Occupant Detection Sensor:
Disconnect the 2 connectors.
Detach the clamp.
Remove the bolt and front center seat belt assembly.
73240
11.REMOVE FRONT SEAT INNER BELT ASSEMBLY RH
w/ Seat Belt Warning System:
| *A | w/ Center Seat Occupant Detection Sensor |
Detach the clamp.
Disconnect the connector.
Remove the bolt.
|
Band |
Detach the band and remove the front seat inner belt assembly RH and seat anchor of the front seat 3 point type belt assembly LH.
12.REMOVE FRONT SEAT CUSHION COVER WITH PAD
Detach the hook.
w/ Seat Belt Warning System:
| *A | w/ Center Seat Occupant Detection Sensor |
Detach the clamp.
Remove the front seat cushion cover with pad.
71071
13.REMOVE FRONT SEAT CUSHION COVER SUB-ASSEMBLY RH
Remove the 11 hog rings and front seat cushion cover sub-assembly RH.
14.REMOVE SEAT COVER WIRE
Remove the seat cover wire.
15.REMOVE CENTER SEATBACK ASSEMBLY
| *1 | Seat Lock Band Assembly |
|
Fold in this Direction |
Pull the seat lock band assembly and move the center seatback assembly as shown in the illustration.
Remove the 3 bolts and center seatback assembly.
71387A
16.REMOVE CENTER SEAT LOWER HINGE ARM RH
Using a T45 "TORX" socket wrench, remove the "TORX" screw, front seat reclining spacer LH and center seat lower hinge arm RH.
Remove the bench type front seat cushion shield together with the center seat lower hinge arm RH.
71811U
17.REMOVE BENCH TYPE FRONT SEAT CUSHION SHIELD
Detach the claw and remove the bench type front seat cushion shield.
71397F
18.REMOVE CENTER SEAT UPPER HINGE COVER RH
|
Remove in this Direction |
Remove the clip.
Detach the guide and remove the center seat upper hinge cover RH as shown in the illustration.
72521
19.REMOVE LOWER RECLINING ADJUSTER ARM RH
Using a T45 "TORX" socket wrench, remove the "TORX" screw, front seat reclining spacer RH and lower reclining adjuster arm RH.
71784A
20.REMOVE FRONT SEATBACK BOARD CAP
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw and guide and remove the front seatback board cap.
Tape the thin-bladed screwdriver tip before use.
71705H
21.REMOVE FRONT CENTER SEATBACK BOARD SUB-ASSEMBLY RH
|
Clip |
|
Screw |
|
Lift up in this Direction |
Using a clip remover, remove the 2 clips.
Remove the 2 screws.
Lift up the front center seatback board sub-assembly RH as shown in the illustration.
|
Remove in this Direction |
Pull in the removal direction shown in the illustration and detach the hook and remove the front center seatback board sub-assembly RH.
22.REMOVE CENTER SEATBACK COVER WITH PAD
|
Remove in this Direction |
Detach the claw and remove the 2 front center seat headrest support assemblies as shown in the illustration.
Detach the hook.
Detach the hook and remove the center seatback cover with pad.
71095
23.REMOVE CENTER SEATBACK COVER SUB-ASSEMBLY
Remove the center seatback cover sub-assembly.
72510H
24.REMOVE FRONT SEATBACK LOCK ASSEMBLY RH
Remove the 2 bolts and front seatback lock assembly RH.
78970G
25.REMOVE FRONT SEATBACK LOCK BAND ASSEMBLY RH
Remove the front seatback lock band assembly RH.
73178A
26.REMOVE SEAT BELT ANCHOR COVER CAP
|
Remove in this Direction |
Using a moulding remover B, detach the claw.
Detach the guide as shown in the illustration.
|
Remove in this Direction |
Detach the guide and remove the seat belt anchor cover cap as shown in the illustration.
73373
27.REMOVE REAR SEAT SHOULDER BELT COVER
| *a | Slit |
Pass the front seat 3 point type belt assembly LH through the slit of the rear seat shoulder belt cover and remove the rear seat shoulder belt cover.
71073A
28.REMOVE FRONT SEATBACK COVER SUB-ASSEMBLY RH
Detach the fastening tape.
|
Fastening Tape | - | - |
Detach the hook.
Pull out the fastener.
Open the fastener.
Remove the clip.
w/ Front Seat Side Airbag:
Remove the nut and bracket of the front seatback cover sub-assembly RH.
Do not reuse the nut.
|
Remove in this Direction |
Detach the claw and remove the 2 front seat headrest support assemblies as shown in the illustration.
Remove the 3 hog rings and front seatback cover sub-assembly RH.
29.REMOVE SEAT COVER WIRE
Remove the seat cover wire.
79158
30.REMOVE SEATBACK COVER PLATE RH
|
Remove in this Direction |
Detach the guide and remove the seatback cover plate RH as shown in the illustration.
71551A
31.REMOVE FRONT SEATBACK PAD RH
Remove the front seatback pad RH.
74810L
32.REMOVE FRONT PROTECTOR ASSEMBLY RH
Using a clip remover, remove the 2 clips.
Detach the guide and remove the front protector assembly RH.
73910B
33.REMOVE FRONT SEAT AIRBAG ASSEMBLY RH (w/ Front Seat Side Airbag)
89178C
34.REMOVE NO. 2 AIRBAG BRACKET (w/ Front Seat Side Airbag)
71H75B
35.REMOVE RH SEATBACK FRAME RECLINING ADJUSTER INSIDE COVER
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw and remove the RH seatback frame reclining adjuster inside cover.
Tape the thin-bladed screwdriver tip before use.
73120
36.REMOVE FRONT SEAT 3 POINT TYPE BELT ASSEMBLY LH
73187
37.REMOVE FRONT SEAT SHOULDER BELT GUIDE
|
Remove in this Direction |
Detach the claw and guide and remove the front seat shoulder belt guide as shown in the illustration.
71862M
38.REMOVE FRONT SEAT INNER NO. 2 CUSHION SHIELD LH
|
Remove in this Direction |
Using moulding remover A, detach the claw as shown in the illustration.
|
Remove in this Direction |
Using moulding remover A, detach the claw as shown in the illustration.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull in the removal direction and detach the clip and remove the front seat inner No. 2 cushion shield LH.
71H75A
39.REMOVE RH SEAT RECLINING ADJUSTER INSIDE COVER
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw and remove the RH seat reclining adjuster inside cover.
Tape the thin-bladed screwdriver tip before use.
71H76
40.REMOVE RH SEAT RECLINING ADJUSTER INSIDE COVER RH
Detach the claw and guide and remove the RH seat reclining adjuster inside cover RH.
72580C
41.REMOVE RH SEAT RECLINING ADJUSTING CABLE ASSEMBLY
| *a | Cable End |
|
Move in this Direction |
Detach the 2 cable clamp.
Disconnect the 2 cable ends by moving them in the direction of the arrows in the illustration and remove the RH seat reclining adjusting cable assembly.
Cut off the 2 cable ties and remove the RH seat reclining adjusting cable assembly.
42.REMOVE FRONT SEATBACK ASSEMBLY RH
Remove the 4 bolts and front seatback assembly RH.
72211F
43.REMOVE SEAT TRACK ADJUSTING HANDLE RH
Operate the seat track adjusting handle RH and move the front seat assembly RH to the rearmost position.
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, push up the plate and state of the detached the guide and pull the seat track adjusting handle RH in the removal direction shown in the illustration and remove it.
Tape the thin-bladed screwdriver tip before use.