Home › Engine / Hybrid System › 7GR-FKS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR
RM35X0E _51 Engine / Hybrid System _078720 7GR-FKS ENGINE CONTROL _0381926 AIR FUEL RATIO SENSOR A

7GR-FKS ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


PROCEDURE

Hide 89467C 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 1)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>7GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A443238C01
0.583,1.167 0.885,1.167 0.885,1.167 1.063,0.979 true 1.625,1.458 1.854,1.677 0.229,0.219 10 true *a 0.271,1.073 0.635,1.302 0.365,0.229 10 true SST
*a Torque Wrench Fulcrum Length


w/o Secondary Air Injection System:

i.

Using SST, install the air fuel ratio sensor.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 37.7 N*m (384 kgf*cm, 28 ft.*lbf).




ii.
A443233

Attach the 2 wire harness clamps.


iii.

Connect the air fuel ratio sensor connector.



b.
A443244C01
0.885,1.188 1.198,1.198 1.198,1.198 1.292,1.052 true 2,1.135 2.229,1.354 0.229,0.219 10 true *a 0.531,1.094 0.896,1.323 0.365,0.229 10 true SST
*a Torque Wrench Fulcrum Length


w/ Secondary Air Injection System:

i.

Using SST, install the air fuel ratio sensor.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 37.7 N*m (384 kgf*cm, 28 ft.*lbf).




ii.
A443239

Attach the 3 wire harness clamps.


iii.

Connect the air fuel ratio sensor connector.



Hide 89467B 2.INSTALL AIR FUEL RATIO SENSOR (for Bank 2)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>7GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A443237C01
1.552,1 1.552,0.375 1.552,0.375 1.792,0.375 true 0.552,1.156 0.75,1.323 0.198,0.167 10 true *a 1.844,0.292 2.156,0.458 0.313,0.167 10 true SST
*a Torque Wrench Fulcrum Length


w/o Secondary Air Injection System:

i.

Using SST, install the air fuel ratio sensor.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 37.7 N*m (384 kgf*cm, 28 ft.*lbf).




ii.
A443235

Attach the wire harness clamp.


iii.

Connect the air fuel ratio sensor connector.



b.
A443243C01
1.552,1 1.552,0.375 1.552,0.375 1.792,0.375 true 0.604,1.198 0.802,1.365 0.198,0.167 10 true *a 1.844,0.292 2.156,0.458 0.313,0.167 10 true SST
*a Torque Wrench Fulcrum Length


w/ Secondary Air Injection System:

i.

Using SST, install the air fuel ratio sensor.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 37.7 N*m (384 kgf*cm, 28 ft.*lbf).




ii.
A443241

Attach the wire harness clamp.


iii.

Connect the air fuel ratio sensor connector.



Hide 11209 3.INSTALL V-BANK COVER SUB-ASSEMBLY (w/ Cover)

Hide 5.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing an air fuel ratio sensor.

Click hereEngine / Hybrid System>7GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION