Home › Drivetrain › RC60J (MANUAL TRANSMISSION / TRANSAXLE) › COUNTER GEAR
RM35X0E _52 Drivetrain _078740 RC60J MANUAL TRANSMISSION / TRANSAXLE _0382066 COUNTER GEAR A

RC60J MANUAL TRANSMISSION / TRANSAXLE  COUNTER GEAR  REASSEMBLY  


PROCEDURE

Hide 33332B 1.INSTALL 2ND GEAR NEEDLE ROLLER BEARING

a.
C323434

Coat the 2nd gear needle roller bearing with gear oil, and then install it to the counter gear.


Hide 33424 2.INSTALL COUNTERSHAFT 2ND SPEED GEAR

a.
C323435

Coat the countershaft 2nd speed gear with gear oil, and then install it to the counter gear.


Hide 33038E 3.INSTALL NO. 2 SYNCHRONIZER RING SET

a.

Coat the No. 2 synchronizer ring set with gear oil.


b.
C334175C01
0.844,0.354 1.021,0.354 1.021,0.354 1.208,0.469 false 0.917,1.01 1.094,1.01 1.094,1.01 1.281,1.125 false 0.99,1.719 1.167,1.719 1.167,1.719 1.354,1.833 false 1.688,1.563 2.01,1.969 2.01,1.969 2.521,1.958 true 1.677,0.198 2,0.604 2,0.604 2.51,0.594 true 0.615,0.281 0.927,0.479 0.313,0.198 10 false *1 0.698,0.969 1.01,1.167 0.313,0.198 10 false *2 0.76,1.646 1.073,1.844 0.313,0.198 10 false *3 2.573,0.521 2.885,0.719 0.313,0.198 10 false *a 2.594,1.865 2.906,2.063 0.313,0.198 10 false *b
*1 No. 2 Synchronizer Ring (Outer Ring)
*2 No. 2 Synchronizer Ring (Middle Ring)
*3 No. 2 Synchronizer Ring (Inner Ring)
*a Cutout
*b Protrusion


Align the 3 synchronizer rings as shown in the illustration.

NOTICE:

Align the protrusion of the No. 2 synchronizer inner ring with the cutout of the No. 2 synchronizer outer ring.



c.
C334176C01
2.063,1.146 2.344,1.146 2.344,1.146 2.458,1.073 true 2.031,2.031 2.313,2.031 2.313,2.031 2.438,1.49 true 1.865,1.042 2.177,1.24 0.313,0.198 10 false *a 1.833,1.927 2.146,2.125 0.313,0.198 10 false *b
*a Protrusion
*b Groove


Install the No. 2 synchronizer ring set to the countershaft 2nd speed gear.

NOTICE:

Align the protrusion of the No. 2 synchronizer middle ring with the groove of the 2nd gear.



Hide 33361 4.INSTALL NO. 1 TRANSMISSION CLUTCH HUB

a.
C323437C01
1.073,0.552 1.271,0.552 1.271,0.552 1.531,0.958 false 2.729,1.156 2.906,0.458 2.906,0.458 3.031,0.458 true 2.417,1.854 2.542,1.854 2.542,1.854 2.74,1.458 true 3.083,0.375 3.396,0.531 0.313,0.156 10 false *a 2.26,1.792 2.573,1.948 0.313,0.156 10 false *b 0.74,0.469 1.198,0.667 0.458,0.198 10 false SST
*a Groove
*b Protrusion


Using SST and a press, install the No. 1 transmission clutch hub to the counter gear.

SST
09316-60012  

NOTICE:

Align the groove of the No. 1 transmission clutch hub with the protrusion of the No. 2 synchronizer ring set.


NOTICE:
·

Pay attention to installation direction of the No. 1 transmission clutch hub.


·

Align the groove of the No. 1 transmission clutch hub with the protrusion of the No. 2 synchronizer ring set.




b.

Check that the countershaft 2nd speed gear and No. 2 synchronizer ring set move smoothly.


Hide 33361B 5.INSTALL NO. 1 CLUTCH HUB SHAFT SNAP RING

a.
C323432

Select a new No. 1 clutch hub shaft snap ring that will allow minimal axial play.

Standard Clearance:

0.1 mm (0.00394 in.) or less


Standard Snap Ring:
Part No. Mark Thickness
90520-T0168 A 2.28 to 2.33 mm (0.0898 to 0.0917 in.)
90520-T0169 B 2.33 to 2.38 mm (0.0918 to 0.0937 in.)
90520-T0170 C 2.38 to 2.43 mm (0.0938 to 0.0956 in.)
90520-T0171 D 2.43 to 2.48 mm (0.0957 to 0.0976 in.)
90520-T0172 E 2.48 to 2.53 mm (0.0977 to 0.0996 in.)
90520-T0173 F 2.53 to 2.58 mm (0.0997 to 0.1015 in.)



b.

Using a snap ring expander, install the No. 1 clutch hub shaft snap ring to the counter gear.


Hide 33365 6.INSTALL NO. 1 SYNCHROMESH SHIFTING KEY

a.
C323438

Install the 3 No. 1 synchromesh shifting keys to the No. 1 transmission clutch hub.


Hide 33363 7.INSTALL NO. 1 TRANSMISSION HUB SLEEVE

a.
C325388

Install the No. 1 transmission clutch hub to the No. 1 transmission clutch hub sleeve.

NOTICE:

Pay attention to installation direction of the No. 1 transmission hub sleeve.



Hide 33037B 8.INSTALL NO. 1 SYNCHRONIZER RING SET

a.

Coat the No. 1 synchronizer ring set with gear oil.


b.
C334177C01
0.927,0.469 1.177,0.469 1.177,0.469 1.344,0.292 false 0.896,1.125 1.146,1.125 1.146,1.125 1.313,0.948 false 0.844,1.854 1.094,1.854 1.094,1.854 1.26,1.677 false 1.708,1.625 1.885,1.74 1.885,1.74 2.344,1.74 true 1.688,0.25 1.865,0.365 1.865,0.365 2.208,0.365 true 0.74,0.396 1.052,0.594 0.313,0.198 10 false *3 0.698,1.031 1.01,1.229 0.313,0.198 10 false *2 2.323,0.292 2.635,0.49 0.313,0.198 10 false *a 0.646,1.781 0.958,1.979 0.313,0.198 10 false *1 2.385,1.656 2.698,1.854 0.313,0.198 10 false *b
*1 No. 1 Synchronizer Ring (Outer Ring)
*2 No. 1 Synchronizer Ring (Middle Ring)
*3 No. 1 Synchronizer Ring (Inner Ring)
*a Protrusion
*b Cutout


Align the 3 No. 1 synchronizer rings as shown in the illustration.

NOTICE:

Align the protrusion of the No. 1 synchronizer inner ring with the cutout of the No. 1 synchronizer outer ring.



c.
C334178C01
1.563,0.219 1.979,0.219 1.979,0.219 2.406,0.958 true 1.552,1.813 1.969,1.813 1.969,1.813 2.427,1.531 true 1.354,0.156 1.667,0.354 0.313,0.198 10 false *a 1.354,1.729 1.667,1.927 0.313,0.198 10 false *b
*a Protrusion
*b Groove


Install the No. 1 synchronizer ring set to the No. 1 transmission clutch hub.

NOTICE:

Align the protrusion of the No. 1 synchronizer outer ring with the groove of the No. 1 transmission clutch hub.



Hide 33335C 9.INSTALL 1ST GEAR NEEDLE ROLLER BEARING

a.
C323440

Coat the 1st gear needle roller bearing with gear oil, and then install it to the counter gear.


Hide 33426A 10.INSTALL COUNTERSHAFT 1ST SPEED GEAR

a.
C325069C01
2.719,1.042 3.073,0.615 true 1.771,2.229 2.094,2.135 true 3.052,0.49 3.365,0.646 0.313,0.156 10 false *a 1.604,2.156 1.917,2.313 0.313,0.156 10 false *b
*a Groove
*b Protrusion


Coat the countershaft 1st speed gear with gear oil and install it to the counter gear.

HINT:

Align the groove of the countershaft 1st speed gear with the protrusion of the No. 1 synchronizer ring set.



Hide 33352B 11.INSTALL NO. 4 TRANSMISSION CLUTCH HUB

a.
C323441N01
0.5,1.021 0.813,1.021 false 0.156,0.948 0.615,1.146 0.458,0.198 10 false SST

Coat the No. 4 transmission clutch hub with gear oil and install it to the counter gear.


b.

Using SST and a press, install the No. 4 transmission clutch hub.

SST
09316-60012  


Hide 33394 12.INSTALL NO. 3 SYNCHROMESH SHIFTING KEY

a.

Install No. 3 synchromesh shifting key.

i.
C334179C01
0.167,1.167 0.167,1.688 0.167,1.688 0.594,1.542 false 0.885,0.906 1.177,0.5 1.177,0.5 1.365,0.5 false 0.052,1.719 0.229,1.906 0.177,0.188 10 false *1 1.396,0.438 1.594,0.615 0.198,0.177 10 false *2
*1 No. 3 Synchromesh Shifting Key
*2 No. 3 Synchromesh Shifting Key Spring


Pinch and lift up the part as shown in the illustration.

HINT:

Refer to the illustration when installing the No. 3 synchromesh shifting key.



ii.
C337240C01
2.615,1.042 2.208,1.042 2.208,1.042 1.813,0.76 false 2.667,2.031 2.26,2.031 2.26,2.031 1.865,1.75 false 2.667,0.958 2.979,1.156 0.313,0.198 10 false *a 2.74,1.948 3.052,2.146 0.313,0.198 10 false *b
*a Protrusion
*b Groove


Install the part to the No. 4 transmission clutch hub as shown in the illustration.

HINT:

Align the groove of the No. 4 transmission sleeve hub with the protrusion of the No. 3 synchromesh shifting key.




Hide 33327 13.INSTALL NO. 4 TRANSMISSION HUB SLEEVE

a.
C334181

Coat the No. 4 transmission hub sleeve with gear oil and install it to the No. 4 transmission clutch hub.

NOTICE:

Pay attention to installation direction of the No. 4 transmission hub sleeve.



Hide 33387A 14.INSTALL REVERSE SYNCHRONIZER RING

a.

Coat the reverse synchronizer ring with gear oil.


b.
C334182C01
1.479,0.208 1.865,0.208 1.865,0.208 2.458,1.146 true 1.396,2.01 1.781,2.01 1.781,2.01 2.49,1.333 true 1.281,0.125 1.594,0.281 0.313,0.156 10 false *a 1.188,1.906 1.5,2.063 0.313,0.156 10 false *b
*a Protrusion
*b Groove


Install reverse synchronizer ring to the No. 4 transmission clutch hub.

HINT:

Align the groove of the No. 4 transmission hub with the protrusion of the reverse synchronizer ring.



Hide 33338C 15.INSTALL REVERSE SHIFT RESTRICT BALL

a.
C323446

Install the reverse shift restrict ball to the counter gear.


Hide 33425 16.INSTALL COUNTERSHAFT REVERSE GEAR

a.
C323447

Coat the countershaft reverse gear with gear oil and install it to the counter gear.

HINT:

Refer to the illustration when installing the countershaft reverse gear.



Hide 33331A 17.INSTALL REVERSE GEAR BEARING

a.
C323448

Coat the reverse gear bearing with gear oil, and then install it to the counter gear.


Hide 33354A 18.INSTALL REVERSE GEAR BEARING INNER RACE

a.
C323449C01
2.531,0.99 2.875,0.615 false 2.479,1.302 2.979,0.969 true 2.885,0.479 3.198,0.635 0.313,0.156 10 false *1 3.031,0.865 3.344,1.021 0.313,0.156 10 false *2
*1 Reverse Gear Bearing Inner Race
*2 Reverse Shift Restrict Ball


Align the groove of the reverse gear bearing inner race with the reverse shift restrict ball and install the reverse gear bearing inner race.


Hide 33411P 19.INSTALL CENTER COUNTER SHAFT BEARING

a.
C323450N01
0.521,0.771 0.76,0.771 false 0.396,1.51 0.833,1.51 true 0.198,0.698 0.656,0.896 0.458,0.198 10 false SST 0.104,1.438 0.563,1.635 0.458,0.198 10 false SST

Using SST and a press, install a new center counter shaft bearing (inner race) to the counter gear.

SST
09316-60012  (09316-00011, 09316-00071)


b.
C323485

Coat a new center counter shaft bearing (outer race) with gear oil, and then install it to the center counter shaft bearing (inner race).


Hide 33411A 20.INSTALL FRONT COUNTER GEAR BEARING OR ROLLER

a.
C323486N01
0.49,0.969 0.792,0.969 false 0.406,1.458 0.813,1.458 true 0.156,0.885 0.615,1.083 0.458,0.198 10 false SST 0.094,1.396 0.552,1.594 0.458,0.198 10 false SST

Using SST and a press, install a new front counter gear bearing or roller (inner race) to the counter gear.

SST
09316-60012  (09316-00011, 09316-00071)


b.
C334821C01
0.948,1.521 1.156,1.958 1.156,1.958 1.354,1.958 false 1.219,1.219 1.385,0.938 1.385,0.938 1.521,0.938 true 1.458,1.5 1.927,0.958 1.927,0.958 2.063,0.958 true 2.49,1.75 2.708,1.083 2.708,1.083 2.906,1.083 true 2.948,1 3.26,1.198 0.313,0.198 10 false *1 1.563,0.854 1.875,1.052 0.313,0.198 10 false *a 2.115,0.854 2.427,1.052 0.313,0.198 10 false *b 1.396,1.865 1.708,2.063 0.313,0.198 10 false *1
*1 O-ring
*a 2.28 to 2.48 mm (0.0898 to 0.0973 in.)
*b 2.85 to 3.05 mm (0.113 to 0.120 in.)
V100135

Gear Oil


Coat a new front counter gear bearing or roller (outer race) with gear oil, and then install it to the front counter gear bearing or roller (inner race).


c.
C323488N01
0.552,0.844 0.854,0.844 false 0.51,1.427 0.896,1.427 true 0.208,0.771 0.667,0.969 0.458,0.198 10 false SST 0.177,1.354 0.635,1.552 0.458,0.198 10 false SST

Using SST and a press, install a new front counter gear bearing or roller (inner race) to the front counter gear bearing or roller (outer race).

SST
09316-60012  (09316-00011, 09316-00071)


Hide 33411H 21.INSTALL REAR COUNTER GEAR BEARING OR ROLLER

a.
C323489N01
0.521,0.969 0.719,0.969 false 0.479,1.604 0.781,1.604 false 0.188,0.885 0.646,1.083 0.458,0.198 10 false SST 0.177,1.552 0.635,1.75 0.458,0.198 10 false SST

Using SST and a press, install the rear counter gear bearing or roller (inner race) to the counter gear.

SST
09316-60012  (09316-00011, 09316-00071)


Hide 33411R 22.INSTALL REAR COUNTER GEAR BEARING SNAP RING

a.
C323239

Select a new rear counter gear bearing snap ring that will allow minimal axial play.

Standard Clearance:

0.1 mm (0.00394 in.) or less


Standard Snap Ring:
Part No. Mark Thickness
90520-T0175 A 2.45 to 2.50 mm (0.0965 to 0.0984 in.)
90520-T0176 B 2.50 to 2.55 mm (0.0985 to 0.1003 in.)
90520-T0177 C 2.55 to 2.60 mm (0.1004 to 0.1023 in.)
90520-T0178 D 2.60 to 2.65 mm (0.1024 to 0.1043 in.)
90520-T0179 E 2.65 to 2.70 mm (0.1044 to 0.1062 in.)
90520-T0180 F 2.70 to 2.75 mm (0.1063 to 0.1082 in.)
90520-T0181 G 2.75 to 2.80 mm (0.1083 to 0.1102 in.)



b.

Using a snap ring expander, install the counter gear rear bearing snap ring to the counter gear.


Hide 33425 23.INSPECT COUNTERSHAFT REVERSE GEAR THRUST CLEARANCE

Hide 33425 24.INSPECT COUNTERSHAFT REVERSE GEAR RADIAL CLEARANCE

Hide 33426A 25.INSPECT COUNTERSHAFT 1ST SPEED GEAR THRUST CLEARANCE

Hide 33426A 26.INSPECT COUNTERSHAFT 1ST SPEED GEAR RADIAL CLEARANCE

Hide 33424 27.INSPECT COUNTERSHAFT 2ND SPEED GEAR THRUST CLEARANCE

Hide 33424 28.INSPECT COUNTERSHAFT 2ND SPEED GEAR RADIAL CLEARANCE