The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the oil cooler removal/installation are shown below.
17140
1.REMOVE EXHAUST MANIFOLD ASSEMBLY RH
2.DRAIN ENGINE COOLANT (w/ ATF Warmer)
3.DRAIN AUTOMATIC TRANSMISSION FLUID
32949
4.REMOVE OIL COOLER HOSE HEAT INSULATOR (w/ ATF Warmer)
Remove the 3 bolts and oil cooler hose heat insulator from the automatic transmission assembly.
32941
5.REMOVE NO. 2 OIL COOLER INLET HOSE AND NO. 2 OIL COOLER OUTLET HOSE (w/ ATF Warmer)
When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.
Use a container to catch any ATF.
| *1 | No. 2 Oil Cooler Inlet Hose |
| *2 | No. 2 Oil Cooler Outlet Hose |
Slide the 2 clips and disconnect the No. 2 oil cooler inlet hose and No. 2 oil cooler outlet hose from the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.
Slide the 2 clips and remove the No. 2 oil cooler inlet hose and No. 2 oil cooler outlet hose from the transmission oil cooler with transmission oil thermostat.
32971
6.REMOVE TRANSMISSION OIL COOLER WITH TRANSMISSION OIL THERMOSTAT (w/ ATF Warmer)
When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.
Use a container to catch any ATF and coolant.
| *1 | No. 3 Water By-pass Hose |
| *2 | No. 4 Water By-pass Hose |
Slide the 2 clips and disconnect the No. 3 water by-pass hose and No. 4 water by-pass hose from the transmission oil cooler with transmission oil thermostat.
Use a container to catch any coolant.
| *1 | No. 1 Oil Cooler Hose |
| *2 | No. 2 Oil Cooler Hose |
Slide the 2 clips and disconnect the No. 1 oil cooler hose and No. 2 oil cooler hose from the automatic transmission assembly.
Slide the 2 clips and remove the No. 1 oil cooler hose and No. 2 oil cooler hose from the transmission oil cooler with transmission oil thermostat.
Remove the 3 bolts and transmission oil cooler with transmission oil thermostat from the automatic transmission assembly.
33493A
7.REMOVE TRANSMISSION OIL COOLER (w/ ATF Warmer)
Use a container to catch any ATF and coolant.
Remove the 3 bolts and transmission oil cooler from the transmission oil thermostat.
Remove the 2 O-rings from the grooves of transmission oil cooler.
32941
8.REMOVE NO. 1 OIL COOLER INLET HOSE AND NO. 1 OIL COOLER OUTLET HOSE
When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.
Use a container to catch any ATF.
| *1 | No. 1 Oil Cooler Inlet Hose |
| *2 | No. 1 Oil Cooler Outlet Hose |
Slide the 2 clips and disconnect the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose from the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.
Disconnect the hose clamp from the fan shroud.
Slide the 2 clips and remove the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose from the radiator assembly.
32921
9.REMOVE NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE (w/ ATF Warmer)
Remove the 2 bolts to open the 2 transmission oil cooler tube clamp sub-assemblies and No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.
Remove the 2 bolts and 2 transmission oil cooler tube clamp sub-assemblies from the engine assembly.
32921
10.REMOVE NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE (w/o ATF Warmer)
Use a container to catch any ATF.
Disconnect the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube from the automatic transmission assembly.
Remove the 3 bolts to open the No. 1 automatic transmission oil cooler tube clamp and 2 transmission oil cooler tube clamp sub-assemblies and remove the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.
| *1 | No. 1 Automatic Transmission Oil Cooler Tube Clamp | *2 | No. 2 Oil Cooler Tube Clamp |
| *3 | Transmission Oil Cooler Tube Clamp Sub-assembly | - | - |
Remove the 3 bolts, No. 2 oil cooler tube clamp and 2 transmission oil cooler tube clamp sub-assemblies from the automatic transmission assembly and engine assembly.