Home › Drivetrain › AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL COOLER (for 7GR-FKS) › 2019.02–2021.07
RM35X0E _52 Drivetrain _078741 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0382309 OIL COOLER(for 7GR-FKS) A

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL COOLER(for 7GR-FKS)  INSTALLATION  


PROCEDURE

Hide 32921 1.INSTALL NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE (w/o ATF Warmer)

a.

Install the No. 2 oil cooler tube clamp and 2 transmission oil cooler tube clamp sub-assemblies to the automatic transmission assembly and engine assembly with the 3 bolts (A).

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)

NOTICE:

When installing the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube, support the tube by hand and be careful to prevent the tube from being deformed.


C412693C01
4.552,0.438 4.667,0.25 4.667,0.25 4.833,0.25 true 5,1.333 4.917,1.333 4.917,1.333 4.75,0.75 true 2.167,0.667 2.417,0.458 2.417,0.458 2.5,0.458 true 5.667,2.167 5.583,2.167 5.583,2.167 5.583,2 true 4.875,0.167 5.042,0.333 0.167,0.167 10 true *1 5.042,1.25 5.208,1.417 0.167,0.167 10 true *2 2.542,0.375 2.708,0.542 0.167,0.167 10 true *3 5.708,2.083 5.875,2.25 0.167,0.167 10 true *3
*1 No. 1 Automatic Transmission Oil Cooler Tube Clamp *2 No. 2 Oil Cooler Tube Clamp
*3 Transmission Oil Cooler Tube Clamp Sub-assembly - -
V100135

Bolt A
V100136

Bolt B



b.

Connect the ends of the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube to the automatic transmission assembly by hand.


c.

Close the No. 1 automatic transmission oil cooler tube clamp and 2 transmission oil cooler tube clamp sub-assemblies and install the 3 bolts (B).

Torque:
5.2 N*m (53 kgf*cm, 46 in.*lbf)


d.
C410507C01
2.083,1.25 2.25,1.417 0.167,0.167 10 true *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.

Torque:
Specified tightening torque : 34.3 N*m (350 kgf*cm, 25 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

(Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

·

When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 29.4 N*m (300 kgf*cm, 22 ft.*lbf)




Hide 32921 2.INSTALL NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE (w/ ATF Warmer)

a.

Install the 2 transmission oil cooler tube clamp sub-assemblies to the engine assembly with the 2 bolts (A and B).

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)

NOTICE:

When installing the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube, support the tube by hand and be careful to prevent the tube from being deformed.


HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (A)


C412508C01
0,0 0,0 false
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C - -



b.

Install the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube to the 2 transmission oil cooler tube clamp sub-assemblies with the 2 bolts (C).

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 32941 3.INSTALL NO. 1 OIL COOLER INLET HOSE AND NO. 1 OIL COOLER OUTLET HOSE

a.
C410509C01
0.917,0.76 0.583,0.667 0.583,0.667 0.5,0.667 true 1.083,2.333 1.25,2.333 1.25,2.333 1.25,2.458 false 1.083,3.167 1.25,3.167 1.25,3.167 1.25,3 false 1.354,0.448 1.521,0.615 0.167,0.167 10 false *a 0.99,0.073 1.156,0.24 0.167,0.167 10 false *b 0.292,0.583 0.458,0.75 0.167,0.167 10 false *c 2.542,0.948 2.708,1.115 0.167,0.167 10 false *d 1.917,0.083 2.083,0.25 0.167,0.167 10 false *e 0.885,2.25 1.052,2.417 0.167,0.167 10 false *1 0.875,3.083 1.042,3.25 0.167,0.167 10 false *2 0.604,1.01 0.938,1.177 0.333,0.167 10 false 45° 1.094,1.01 1.427,1.177 0.333,0.167 10 false 45°
*1 No. 1 Oil Cooler Inlet Hose
*2 No. 1 Oil Cooler Outlet Hose
*a Right Side of Vehicle
*b Upper Side of Vehicle
*c Paint Mark
*d 2 to 5 mm (0.0787 to 0.197 in.)
*e 0 to 3 mm (0 to 0.118 in.)


Install the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose to the radiator assembly, and slide the 2 clips to secure the hose.

NOTICE:
·

Make sure to slide the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose until each contacts the hose stopper of the radiator assembly.

·

Make sure that the claws of each clip are within the location shown in the illustration.




b.

Connect the hose clamp to the fan shroud.


c.
C410508C01
0.75,1.25 0.917,1.25 0.917,1.25 1.031,0.854 true 1.583,1.25 2,0.833 true 1.5,1.25 1.583,1.25 1.583,1.25 1.833,0.833 true 1.396,0.74 1.563,0.906 0.167,0.167 10 false *a 0.729,0.292 0.896,0.458 0.167,0.167 10 false *b 2.365,0.313 2.531,0.479 0.167,0.167 10 false *d 2.219,1.188 2.385,1.354 0.167,0.167 10 false *e 1.302,0.5 1.635,0.667 0.333,0.167 10 false 45° 1.292,1.167 1.458,1.333 0.167,0.167 10 false *c 1.313,0.948 1.646,1.115 0.333,0.167 10 false 45° 0.542,1.167 0.708,1.333 0.167,0.167 10 false *c
*a Right Side of Vehicle
*b Upper Side of Vehicle
*c Paint Mark
*d 2 to 5 mm (0.0787 to 0.197 in.)
*e 0 to 3 mm (0 to 0.118 in.)


Connect the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose to the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube, and slide the 2 clips to secure the hose.

NOTICE:
·

Make sure to slide the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose until each contacts the hose stopper of the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.

·

Make sure to align the paint mark of the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose with the paint mark of the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.

·

Make sure that the claws of each clip are within the location shown in the illustration.




Hide 33493A 4.INSTALL TRANSMISSION OIL COOLER (w/ ATF Warmer)

a.

Coat 2 new O-rings with ATF, and install them to the transmission oil cooler.


b.

Install the transmission oil cooler to the transmission oil thermostat with the 3 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 32971 5.INSTALL TRANSMISSION OIL COOLER WITH TRANSMISSION OIL THERMOSTAT (w/ ATF Warmer)

a.
C412507C01
0,0 0,0 false
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


Install the transmission oil cooler with transmission oil thermostat to the automatic transmission assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A)



b.
C410510C01
1.333,2.333 1.5,2.333 1.5,2.333 1.5,2.167 true 1.167,2.583 1.25,2.583 1.25,2.583 1.354,2.667 true 1,0.833 0.583,1.333 0.583,1.333 0.5,1.333 true 2.573,4.021 2.917,4.167 2.917,4.167 3,4.167 true 2.917,4.167 2.802,4.031 true 2.583,0.854 2.5,1.333 2.5,1.333 2.333,1.333 true 0.958,2.5 1.125,2.667 0.167,0.167 10 true *2 1.125,2.25 1.292,2.417 0.167,0.167 10 true *1 2.958,0.75 3.125,0.917 0.167,0.167 10 false *a 2.292,0.292 2.458,0.458 0.167,0.167 10 false *b 0.292,1.25 0.458,1.417 0.167,0.167 10 false *c 1.333,0.302 1.5,0.469 0.167,0.167 10 false *d 1.208,1.219 1.375,1.385 0.167,0.167 10 false *e 2.854,1 3.188,1.167 0.333,0.167 10 false 45° 2.927,3.458 3.094,3.625 0.167,0.167 10 false *d 2.917,4.333 3.083,4.5 0.167,0.167 10 false *e 3.042,4.083 3.208,4.25 0.167,0.167 10 false *c 2.125,1.25 2.292,1.417 0.167,0.167 10 false *c 2.854,0.542 3.188,0.708 0.333,0.167 10 false 45°
*1 No. 1 Oil Cooler Hose
*2 No. 2 Oil Cooler Hose
*a Right Side of Vehicle
*b Upper Side of Vehicle
*c Paint Mark
*d 2 to 7 mm (0.0787 to 0.276 in.)
*e 0 to 3 mm (0 to 0.118 in.)


Install the No. 1 oil cooler hose and No. 2 oil cooler hose to the transmission oil cooler with transmission oil thermostat, and slide the 2 clips to secure the hose.


c.

Connect the No. 1 oil cooler hose and No. 2 oil cooler hose to the automatic transmission assembly, and slide the 2 clips to secure the hose.

NOTICE:
·

Make sure to slide the No. 1 oil cooler hose and No. 2 oil cooler hose until each contacts the hose stopper of the transmission oil cooler with transmission oil thermostat and automatic transmission assembly.

·

Make sure to align the paint mark of the No. 1 oil cooler hose and No. 2 oil cooler hose with the paint mark of the transmission oil cooler with transmission oil thermostat.

·

Make sure that the claws of each clip are within the location shown in the illustration.




d.
C410511C01
0.75,3 0.917,3 0.917,3 0.917,2.667 true 2.583,1.5 2.75,1.5 2.75,1.5 2.75,1.917 true 0.938,1.104 1.25,0.833 1.25,0.833 1.417,0.833 true 1.083,1.083 1.25,0.833 false 0.542,2.917 0.708,3.083 0.167,0.167 10 true *1 2.375,1.417 2.542,1.583 0.167,0.167 10 true *2 1.25,0.458 1.417,0.625 0.167,0.167 10 false *a 1.271,1.5 1.438,1.667 0.167,0.167 10 false *b 1.458,0.729 1.625,0.896 0.167,0.167 10 false *c
*1 No. 3 Water By-pass Hose
*2 No. 4 Water By-pass Hose
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b 0 to 3 mm (0 to 0.118 in.)
*c Paint Mark


Connect the No. 3 water by-pass hose and No. 4 water by-pass hose to the transmission oil cooler with transmission oil thermostat, and slide the 2 clips to secure the hose.

NOTICE:
·

Make sure to slide the No. 3 water by-pass hose and No. 4 water by-pass hose until each contacts the hose stopper of the transmission oil cooler with transmission oil thermostat.

·

Make sure to align the paint mark of the No. 3 water by-pass hose and No. 4 water by-pass hose with the paint mark of the transmission oil cooler with transmission oil thermostat.




Hide 32943 6.INSTALL NO. 2 OIL COOLER INLET HOSE AND NO. 2 OIL COOLER OUTLET HOSE (w/ ATF Warmer)

a.
C410512C01
0.333,0.667 0.5,0.667 0.5,0.667 0.792,0.854 true 0.5,0.667 0.583,0.854 true 2.25,4 2.333,4 2.333,4 2.667,4.104 true 1.25,2.667 1.417,2.667 1.417,2.667 1.5,2.885 true 1.583,1.833 1.833,1.833 1.833,1.833 1.833,2.083 true 1.365,1.75 1.531,1.917 0.167,0.167 10 true *1 1.042,2.583 1.208,2.75 0.167,0.167 10 true *2 2.615,3.354 2.781,3.521 0.167,0.167 10 false *a 3.104,3.792 3.271,3.958 0.167,0.167 10 false *b 0.125,0.583 0.292,0.75 0.167,0.167 10 false *c 1.115,0.292 1.281,0.458 0.167,0.167 10 false *d 0.938,1.219 1.104,1.385 0.167,0.167 10 false *e 2.396,4.375 2.729,4.542 0.333,0.167 10 false 45° 1.865,3.438 2.031,3.604 0.167,0.167 10 false *f 1.896,4.365 2.063,4.531 0.167,0.167 10 false *e 2.042,3.917 2.208,4.083 0.167,0.167 10 false *c 2.865,4.365 3.198,4.531 0.333,0.167 10 false 45°
*1 No. 2 Oil Cooler Inlet Hose
*2 No. 2 Oil Cooler Outlet Hose
*a Left Side of Vehicle
*b Front Side of Vehicle
*c Paint Mark
*d 2 to 7 mm (0.0787 to 0.276 in.)
*e 0 to 3 mm (0 to 0.118 in.)
*f 2 to 5 mm (0.0787 to 0.197 in.)


Install the No. 2 oil cooler inlet hose and No. 2 oil cooler outlet hose to the transmission oil cooler with transmission oil thermostat, and slide the 2 clips to secure the hose.


b.

Connect the No. 2 oil cooler inlet hose and No. 2 oil cooler outlet hose to the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube, and slide the 2 clips to secure the hose.

NOTICE:
·

Make sure to slide the No. 2 oil cooler inlet hose and No. 2 oil cooler outlet hose until each contacts the hose stopper of the transmission oil cooler with transmission oil thermostat, No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.

·

Make sure to align the paint mark of the No. 2 oil cooler inlet hose and No. 2 oil cooler outlet hose with the paint mark of the transmission oil cooler with transmission oil thermostat.

·

Make sure that the claws of each clip are within the location shown in the illustration.




Hide 32949 7.INSTALL OIL COOLER HOSE HEAT INSULATOR (w/ ATF Warmer)

a.
C412609C01
0,0 0,0 false
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


Install the oil cooler hose heat insulator to the automatic transmission assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A)



Hide 17140 8.INSTALL EXHAUST MANIFOLD ASSEMBLY RH

Hide 9.ADD ENGINE COOLANT (w/ ATF Warmer)

Hide 11.INSPECT FOR COOLANT LEAK (w/ ATF Warmer)