Home › Engine / Hybrid System › 7GR-FKS (INTAKE / EXHAUST) › EXHAUST MANIFOLD
RM35X0E _51 Engine / Hybrid System _079308 7GR-FKS INTAKE / EXHAUST _0385727 EXHAUST MANIFOLD A

7GR-FKS INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/o Secondary Air Injection System)

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold assembly LH with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 89467B 2.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

Hide 17150 3.INSTALL EXHAUST MANIFOLD ASSEMBLY LH

a.

Install a new gasket to the cylinder head LH.

NOTICE:

Be careful of the installation direction.



b.

w/o Secondary Air Injection System:

i.

Temporarily install the exhaust manifold assembly LH with the 4 nuts.


ii.
A437899E01
0.76,0.104 0.917,0.302 0.156,0.198 10 true 3 1.458,0.073 1.615,0.271 0.156,0.198 10 true 1 0.625,1.802 0.781,2 0.156,0.198 10 true 2 1.5,1.792 1.656,1.99 0.156,0.198 10 true 4

Tighten the 4 nuts in the sequence shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


iii.

Connect the air fuel ratio sensor connector and attach the wire harness clamp.



c.

w/ Secondary Air Injection System:

i.

Temporarily install the exhaust manifold assembly LH with the 6 nuts.


ii.
A437914E01
0.302,0.177 0.51,0.333 0.208,0.156 10 true 5 1.833,1.667 2.042,1.823 0.208,0.156 10 true 4 0.573,1.573 0.781,1.729 0.208,0.156 10 true 2 2.021,0.115 2.229,0.271 0.208,0.156 10 true 6 1.594,0.104 1.802,0.26 0.208,0.156 10 true 1 1.042,0.125 1.25,0.281 0.208,0.156 10 true 3

Tighten the 6 nuts in the sequence shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


iii.

Connect the air fuel ratio sensor connector and attach the wire harness clamp.



Hide 17362 4.INSTALL NO. 2 AIR TUBE (w/ Secondary Air Injection System)

a.
A437913C01
1.927,0.26 2.083,0.458 0.156,0.198 10 false .
V100135

Bolt
V100136

Nut


Install 2 new gaskets and the No. 2 air tube to the exhaust manifold assembly LH and No. 2 emission control valve set with the 2 bolts and 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:

Do not reuse the gasket.



Hide 17119 5.INSTALL NO. 2 MANIFOLD STAY

a.

Temporarily install the No. 2 manifold stay to the transmission assembly and exhaust manifold assembly LH with the 3 bolts.


b.
A441049C02
0.125,0.073 0.438,0.229 0.313,0.156 10 true *A 0.104,2.5 0.417,2.656 0.313,0.156 10 true *B 1.948,2.083 2.104,2.281 0.156,0.198 10 true 1 2.198,4.427 2.354,4.625 0.156,0.198 10 true 1 2.219,4.417 2.375,4.615 0.156,0.198 10 true 1 1.292,3.104 1.448,3.302 0.156,0.198 10 true 2 1.146,0.625 1.302,0.823 0.156,0.198 10 true 2 1.406,0.115 1.563,0.313 0.156,0.198 10 true 3 1.479,2.521 1.635,2.719 0.156,0.198 10 true 3
*A w/ Secondary Air Injection System
*B w/o Secondary Air Injection System


Tighten the 3 bolts in the sequence shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 89467B 6.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

Hide 17140 7.INSTALL EXHAUST MANIFOLD ASSEMBLY RH

a.

Install a new gasket to the cylinder head assembly RH.

NOTICE:

Be careful of the installation direction.



b.

w/ Secondary Air Injection System:

i.

Temporarily install the exhaust manifold assembly RH with the 6 nuts.


ii.
A437912E01
2.5,0.083 2.656,0.281 0.156,0.198 10 true 3 1.885,0.083 2.031,0.292 0.146,0.208 10 true 1 3.042,0.146 3.188,0.354 0.146,0.208 10 true 5 2.49,1.521 2.635,1.729 0.146,0.208 10 true 2 1.302,1.656 1.448,1.865 0.146,0.208 10 true 4 1.167,0.115 1.313,0.323 0.146,0.208 10 true 6

Tighten the 6 nuts in the sequence shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


iii.

Connect the air fuel ratio sensor connector and attach the 2 wire harness clamps.



c.

w/o Secondary Air Injection System:

i.

Temporarily install the exhaust manifold assembly RH with the 5 nuts.


ii.
A437897E01
1.667,0.156 1.854,0.323 0.188,0.167 10 true 1 2.49,0.094 2.677,0.26 0.188,0.167 10 true 4 1.521,1.906 1.708,2.073 0.188,0.167 10 true 3 2.177,1.927 2.365,2.094 0.188,0.167 10 true 5 3.125,1.771 3.313,1.938 0.188,0.167 10 true 2

Tighten the 5 nuts in the sequence shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


iii.

Connect the air fuel ratio sensor connector and attach the wire harness clamp.



Hide 17361N 8.INSTALL NO. 1 AIR TUBE (w/ Secondary Air Injection System)

a.
A437911C01
2.281,0.406 2.438,0.604 0.156,0.198 10 false .
V100135

Bolt
V100136

Nut


Install 2 new gaskets and the No. 1 air tube to the exhaust manifold assembly RH and No. 1 emission control valve set with the 2 bolts and 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:

Do not reuse the gasket.



Hide 11409 9.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE (w/ Secondary Air Injection System)

Hide 17118 10.INSTALL MANIFOLD STAY

a.

Temporarily install the manifold stay to the transmission assembly and exhaust manifold assembly RH with the 3 bolts.


b.
A441048C02
0.125,0.073 0.438,0.229 0.313,0.156 10 true *A 0.115,2.479 0.427,2.635 0.313,0.156 10 true *B 0.667,4.073 0.844,4.271 0.177,0.198 10 true 1 1.01,1.948 1.167,2.146 0.156,0.198 10 true 1 2.219,3.021 2.375,3.219 0.156,0.198 10 true 2 2.448,0.823 2.604,1.021 0.156,0.198 10 true 2 2.323,0.313 2.479,0.51 0.156,0.198 10 true 3 2.031,2.448 2.188,2.646 0.156,0.198 10 true 3
*A w/ Secondary Air Injection System
*B w/o Secondary Air Injection System


Tighten the 3 bolts in the sequence shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17450B 11.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

40.5 mm (1.59 in.)


If the free length is less than the minimum, replace the compression spring.


b.
A076194C47
2.031,1.583 1.594,1.885 1.594,1.885 1.479,1.885 true 2.438,0.979 3.042,0.979 true 1.271,1.781 1.49,1.958 0.219,0.177 10 false *1 3.104,0.875 3.323,1.052 0.219,0.177 10 false *a
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front exhaust pipe assembly.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the center exhaust pipe assembly, do not push in the gasket with the center exhaust pipe assembly.




c.

Install the 2 new gaskets to the front No. 2 exhaust pipe assembly.


d.

Install the front No. 2 exhaust pipe assembly with the 2 bolts, 2 compression springs and 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.

Connect the heated oxygen sensor connector and wire harness clamp.


Hide 17410 12.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install the 2 new gasket to the front exhaust pipe assembly.


b.

Install the front exhaust pipe assembly with the 2 bolts and 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


c.

w/ Secondary Air Injection System:

Connect the heated oxygen sensor connector.


d.

w/o Secondary Air Injection System:

Connect the heated oxygen sensor connector and wire harness clamp.


Hide 17403 13.INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

Hide 14.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

Hide 51405A 15.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 52618 16.INSTALL LOWER FRONT BUMPER ABSORBER

Hide 51406A 17.INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)