Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P003012  HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery  P003013  HO2S Heater Control Bank 1 Sensor 1 Circuit Open  P101A9E  A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On  


DESCRIPTION

HINT:
·

For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION

·

This DTC is related to the air fuel ratio sensor, although the caption is the oxygen sensor.



The air fuel ratio sensor outputs a voltage* that is proportional to the air fuel ratio. The air fuel ratio sensor output voltage is used to control the air fuel ratio mixture.

The air fuel ratio sensor is located after the Diesel Particulate Filter (DPF) catalytic converter. This sensor has been developed based on the structure and technology of the air fuel ratio sensor that is used for gasoline engine. The cover for the sensor electrode has been modified to suit its application in a diesel engine. This change allows the sensor to function effectively in this DPF type diesel engine, and it also avoids problems with sensor temperature and Particulate Matter (PM).

In order to reduce PM, the ECM adjusts the air fuel ratio to a value slightly richer than that which would otherwise be used (note that this mixture is still leaner than the stoichiometric air fuel ratio). The ECM controls these adjustments on signals from the air fuel ratio sensor.

When the ECM performs PM forced regeneration (cleaning) by adding fuel using the exhaust fuel addition injector assembly, the air fuel ratio sensor feedback is used to ensure that an appropriate air fuel ratio is maintained.

*: This voltage change occurs only inside the ECM. It is not possible to measure this voltage at the sensor. The GTS can be used to monitor this voltage.

A443597E03
3.281,2.146 3.531,1.813 3.531,1.813 3.646,1.813 true 3.135,2.156 2.635,1.885 2.635,1.885 2.531,1.885 true 5.333,1.323 5.583,0.99 5.583,0.99 5.698,0.99 true 5.083,1.271 4.948,0.771 4.948,0.771 4.729,0.771 true 5.167,1.729 5.781,1.208 true 5.01,1.75 5.771,1.219 5.771,1.219 5.865,1.219 true 5.927,2.313 5.208,1.927 true 1.042,2.177 2,2.417 0.958,0.24 10 false Exhaust Gas 2,1.802 2.646,2.021 0.646,0.219 10 false Element 3.677,1.75 4.135,1.969 0.458,0.219 10 false Cover 2.729,2.542 3,2.75 0.271,0.208 10 false A 3.458,2.531 3.729,2.74 0.271,0.208 10 false A 4.813,2.542 5.625,2.802 0.813,0.26 10 false A-A Section 0.135,2.656 2.5,2.917 2.365,0.26 10 false Air Fuel Ratio Displayed on GTS: 0.281,3.604 2.771,3.927 2.49,0.323 10 false A/F (O2) Lambda B1S1 1.583,5.667 1.958,5.906 0.375,0.24 10 false 0.83 4.01,5.115 5.573,5.333 1.563,0.219 10 false Air-Fuel Ratio 3.875,4.094 6.938,4.375 3.063,0.281 10 false A/F (O2) Lambda B1S1 = Air-Fuel Ratio / 14.5 2.135,5.667 2.51,5.906 0.375,0.24 10 false 1.00 1.875,3.646 2.458,3.854 0.583,0.208 10 false 2 1.875,4.167 2.458,4.375 0.583,0.208 10 false 1 1.885,3.135 2.469,3.344 0.583,0.208 10 false 3 3.677,0.688 4.802,1.083 1.125,0.396 10 false Solid Electrolyte (Zirconia Element) 5.75,0.896 6.385,1.115 0.635,0.219 10 false Heater 5.938,1.125 7.156,1.313 1.219,0.188 10 false Platinum Electrode 6.01,2.26 6.49,2.448 0.479,0.188 10 false Air 2.677,5.667 3.052,5.906 0.375,0.24 10 false 1.03 3.229,5.667 3.604,5.906 0.375,0.24 10 false 1.10 3.781,5.667 4.156,5.906 0.375,0.24 10 false 1.17 4.333,5.677 4.708,5.917 0.375,0.24 10 false 1.24 4.885,5.667 5.26,5.906 0.375,0.24 10 false 1.38 5.406,5.667 5.781,5.906 0.375,0.24 10 false 1.72 5.958,5.667 6.333,5.906 0.375,0.24 10 false 2.07 6.521,5.667 6.896,5.906 0.375,0.24 10 false 3.45 2.802,4.917 3.083,5.104 0.281,0.188 10 false 10 3.583,4.917 3.865,5.104 0.281,0.188 10 false 20 4.333,4.917 4.615,5.104 0.281,0.188 10 false 30 5.083,4.917 5.365,5.104 0.281,0.188 10 false 40 5.833,4.917 6.115,5.104 0.281,0.188 10 false 50 0.448,6.104 1.365,6.375 0.917,0.271 10 false Air Fuel Ratio 1.625,6.167 2,6.406 0.375,0.24 10 false 12 2.135,6.167 2.51,6.406 0.375,0.24 10 false 14.5 2.75,6.167 3.125,6.406 0.375,0.24 10 false 15 3.292,6.167 3.667,6.406 0.375,0.24 10 false 16 3.854,6.167 4.229,6.406 0.375,0.24 10 false 17 4.396,6.167 4.771,6.406 0.375,0.24 10 false 18 4.958,6.167 5.333,6.406 0.375,0.24 10 false 20 5.49,6.167 5.865,6.406 0.375,0.24 10 false 25 6.031,6.167 6.406,6.406 0.375,0.24 10 false 30 6.583,6.167 6.958,6.406 0.375,0.24 10 false 50 0.323,5.542 1.406,5.99 1.083,0.448 10 false A/F (O2) Lambda B1S1 3.125,4.917 3.5,5.156 0.375,0.24 10 false 14.5

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P003012 HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery Air fuel ratio sensor heater current is 11.5 A or higher when the heater does not operate for 10 seconds (1 trip detection logic).
·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM


Comes on DTC stored SAE Code: P0032
P003013 HO2S Heater Control Bank 1 Sensor 1 Circuit Open Air fuel ratio sensor heater current is 0.8 A or less when the heater operates for 10 seconds (1 trip detection logic).
·

Open in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM


Comes on DTC stored SAE Code: P0031
P101A9E A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On The air fuel ratio sensor heater voltage level is low while the heater is not operating (1 trip detection logic).
·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM


Comes on DTC stored SAE Code: P101D

Related Data List
DTC No. Data List
P003012
P003013
P101A9E
·

A/F (O2) Lambda B1S1

·

Exhaust Temperature B1S2



MONITOR DESCRIPTION

The inner surface of the air fuel ratio sensor element is exposed to outside air. The outer surface of the sensor element is exposed to exhaust gases. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations of the exhaust and the outside air. The platinum coating amplifies the voltage generation. When heated, the sensor becomes very efficient. If the temperature of the exhaust is low without supplemental heating, the sensor will not generate useful voltage signals. The ECM controls the heating by using a duty-cycle to regulate the average current in the heater element. If the heater current is out of the normal range, the output signals of the sensor are inaccurate and the ECM cannot regulate the air fuel ratio properly. When the heater current is out of the normal operating range, the ECM interprets this as a malfunction and stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P003012
P101A9E
Ignition switch ON for 10 seconds
P003013
·

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

·

Check that "Exhaust Temperature B1S2" displays 200°C (392°F) or higher using the GTS.



WIRING DIAGRAM

A444423E02
0.646,4.75 1.875,4.948 1.229,0.198 10 false Battery 4.76,3.854 5.99,4.052 1.229,0.198 10 false EFI NO. 4 5.99,4.083 6.302,4.281 0.313,0.198 10 false N2 6,2.573 6.313,2.771 0.313,0.198 10 false E6 6,1.635 6.313,1.833 0.313,0.198 10 false E6 6,0.865 6.313,1.063 0.313,0.198 10 false E6 3.25,1.969 3.563,2.167 0.313,0.198 10 false E19 3.25,2.115 5.146,2.469 1.896,0.354 10 false Air Fuel Ratio Sensor 3.292,1.531 3.604,1.729 0.313,0.198 10 false 4 3.292,0.74 3.604,0.938 0.313,0.198 10 false 2 6.01,1.438 6.323,1.635 0.313,0.198 10 false 33 4.365,0.729 4.677,0.927 0.313,0.198 10 false 1 4.375,1.531 4.688,1.729 0.313,0.198 10 false 3 6.031,0.667 6.344,0.865 0.313,0.198 10 false 5 6,2.385 6.313,2.583 0.313,0.198 10 false 25 5.99,3.865 6.302,4.063 0.313,0.198 10 false 14 4.25,3.99 4.563,4.188 0.313,0.198 10 false 2 3.469,3.99 3.781,4.188 0.313,0.198 10 false 1 3.479,3.573 3.792,3.771 0.313,0.198 10 false 3 4.25,3.594 4.563,3.792 0.313,0.198 10 false 5 4.781,3.542 5.094,3.74 0.313,0.198 10 false 1 5.177,3.521 5.49,3.719 0.313,0.198 10 false 2 1.271,3.833 2.5,4.031 1.229,0.198 10 false EFI-MAIN 1.75,3.594 2.063,3.792 0.313,0.198 10 false 2 1.302,3.583 1.615,3.781 0.313,0.198 10 false 1 6.302,0.865 6.792,1.104 0.49,0.24 10 false HA1A 0.49,4.094 1.719,4.292 1.229,0.198 10 false FL MAIN 6.469,4.896 7.156,5.24 0.688,0.344 10 false ECM 3.635,4.438 4.865,4.635 1.229,0.198 10 false EFI MAIN 3.49,0.75 3.979,0.99 0.49,0.24 10 false +B 6.323,2.573 6.813,2.813 0.49,0.24 10 false A1A- 3.927,1.51 4.417,1.75 0.49,0.24 10 false A1A+ 3.896,0.75 4.385,0.99 0.49,0.24 10 false HA1A 6.313,1.646 6.802,1.885 0.49,0.24 10 false A1A+ 6.292,3.99 6.781,4.229 0.49,0.24 10 false MREL 3.51,1.5 4,1.74 0.49,0.24 10 false A1A-

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR HEATER VOLTAGE)

NG

9.REPLACE AIR FUEL RATIO SENSOR
2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR HEATER VOLTAGE)
a.
A436860C01
0.635,1.979 1.125,2.271 0.49,0.292 1.969,2.042 2.542,1.865 true 0.208,0.281 0.469,0.49 0.26,0.208 10 false *a 2.583,1.771 2.802,1.948 0.219,0.177 10 false +B 0.76,2.042 1.125,2.281 0.365,0.24 10 false E19
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E19-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - EFI MAIN RELAY)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E19-1 (HA1A) - E6-5 (HA1A) Always Below 1 Ω
E19-1 (HA1A) or E6-5 (HA1A) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - EFI MAIN RELAY)
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the EFI MAIN relay from the No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E19-2 (+B) - EFI MAIN relay terminal 5 Always Below 1 Ω
E19-2 (+B) or EFI MAIN relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT ECM POWER SOURCE CIRCUIT

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.INSPECT ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle at 50 km/h (30 mph) or higher for a total of 300 seconds or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

"Exhaust Temperature B1S2" on the GTS screen should be 200°C (392°F) or higher.



i.

Confirm that the DTC is not output.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P003012, P003013 or P101A9E.


iii.

Check that STATUS is NORMAL.

HINT:
·

If STATUS is NORMAL, DTC judgment is complete and the system is determined to be normal.

·

If STATUS is INCOMPLETE, DTC judgment is incomplete. Drive the vehicle at 50 km/h (30 mph) or higher for a total of 300 seconds or more again.





Result:
Proceed to
NEXT



NEXT

END

9.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED