Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P040318  Exhaust Gas Recirculation "A" Circuit Current Below Threshold  P040319  Exhaust Gas Recirculation "A" Circuit Current Above Threshold  


DESCRIPTION

The EGR actuator is operated by the ECM and opens and closes the EGR valve using gears. The opening angle of the EGR valve is detected by the EGR position sensor, which is mounted on the electric EGR control valve assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P040318 Exhaust Gas Recirculation "A" Circuit Current Below Threshold Both of the following conditions are met for 2.0 seconds (1 trip detection logic):
·

The EGR actuator duty cycle is 80% or higher.

·

EGR actuator current is below 0.5 A.


·

Open or short in EGR actuator circuit

·

Electric EGR control valve assembly

·

ECM


Comes on DTC stored SAE Code: P0489
P040319 Exhaust Gas Recirculation "A" Circuit Current Above Threshold Either of the following conditions is met for 2.0 seconds (1 trip detection logic):
·

EGR actuator output current 7 A or higher is detected.

·

ECM internal circuit temperature of 150 to 160°C (302 to 320°F) or higher is detected.


·

Open or short in EGR actuator circuit

·

Electric EGR control valve assembly

·

ECM


Comes on DTC stored SAE Code: P0490

Related Data List
DTC No. Data List
P040318
P040319
·

Actual EGR Valve Position No.1

·

Target EGR Valve Position No.1



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P040318
P040319
Idle the engine for 5 seconds or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (RESISTANCE OF EGR ACTUATOR)
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL


b.
A351114C15
0.135,0.104 0.448,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Electric EGR Control Valve Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 - 4 Always No short or no open circuit



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ELECTRIC EGR CONTROL VALVE ASSEMBLY - ECM)

NG

6.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (ELECTRIC EGR CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E33-4 (M+) - E7-6 (EGM+) Always Below 1 Ω
E33-5 (M-) - E7-7 (EGM-) Always Below 1 Ω
E33-4 (M+) or E7-6 (EGM+) - Body ground and other terminals Always 10 kΩ or higher
E33-5 (M-) or E7-7 (EGM-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

Idle the engine for 5 seconds or more


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED