Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P204A1C  Reductant Pressure Sensor Circuit Range/Performance Circuit Voltage Out of Range  


DESCRIPTION

Refer to DTC P208A14.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P208A14

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P204A1C Reductant Pressure Sensor Circuit Range/Performance Circuit Voltage Out of Range When the urea pump is not rotating (urea pump operation check complete and not being filled), the pressure sensor value is outside of a fixed range (1 trip detection logic). Pressure sensor (urea pump) Comes on DTC stored SAE Code: P204B

Related Data List
DTC No. Data List
P204A1C Reductant Pressure

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P204A1C Ignition switch to ON for 5 seconds or more

CAUTION / NOTICE / HINT

NOTICE:
Handling the urea injector set
·

The urea injector set is a precision instrument. Take necessary precautions for installation and shipping. Do not use the part if it has been struck or dropped.

·

If the urea solution remaining inside the urea injector set dries out, it may become unable to inject urea solution. Therefore, conduct urea tube with heater assembly installation and removal quickly.

·

If the urea solution dries out and deposition occurs, urea may cling to the O-ring of the pipe and cause seal problems. Therefore, clean the urea tube with heater assembly and intake port of the urea injector set with water before attaching them.

·

Perform this procedure in an environment where urea solution will not freeze.



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P204A1C)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
DTC P204A1C is output A
DTC P204A1C and other DTCs are output* B


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.




A

2.CHECK AROUND BOTTOM VEHICLE

B

2.CHECK AROUND BOTTOM VEHICLE
a.

Check around the bottom of the vehicle.

HINT:

If the urea solution dries on an object, deposition occurs and leaves behind a white powder.


Area to check:

·

Areas connecting the urea pump and urea injector set.

·

Perforations in the urea tank sub-assembly.

·

Connectors not connected properly.

·

Clogging of the cooling fins of the urea injector set.

HINT:

If the cooling fins are clogged with foreign matter, remove the foreign matter and clean the cooling fins.




b.

Repair any trouble areas.


Result:
Proceed to
NEXT



NEXT

3.PERFORM ACTIVE TEST USING GTS (PRESSURE SENSOR CHECK)
3.PERFORM ACTIVE TEST USING GTS (PRESSURE SENSOR CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pump Check (Backward).

Powertrain > Engine > Active Test
Tester Display
Reductant Pump Check (Backward)
50004 372 85

d.

Perform the Active Test.


e.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Purge / Data List / Diesel Exhaust / Reductant Pressure.

Powertrain > Engine > Active Test
Active Test Display
Reductant Purge
Data List Display
Reductant Pressure
50004 372 86 1030

f.

After executing the Active Test, check the Reductant Pressure.

Standard:

Approximately 0 kPa



g.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Filling (Pressure Keep) / Data List / Diesel Exhaust / Reductant Pressure.

Powertrain > Engine > Active Test
Active Test Display
Reductant Filling (Pressure Keep)
Data List Display
Reductant Pressure
50004 372 84 1030

h.

After executing the Active Test, check the Reductant Pressure.

HINT:

Perform the Active Test until the pressure stabilizes (may take from 5 to 60 seconds).


OK:

400 to 600 kPa



Result:
Proceed to
OK
NG



OK

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

4.REPLACE UREA PUMP
4.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Wait for 5 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END