Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › UREA PUMP
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384127 UREA PUMP A

1GD-FTV EMISSION CONTROL  UREA PUMP  REMOVAL  


PROCEDURE

Hide 77801A 1.REMOVE UREA TANK SUB-ASSEMBLY

Hide 77871A 2.REMOVE UREA PUMP

a.
A436308C01
1.542,1.552 0.656,1.552 true 0.979,1.563 0.979,1.813 0.979,1.813 1.479,1.813 true 0.438,1.448 0.656,1.615 0.219,0.167 10 true *a
*a Co-rotation Prevention Check Mark


Apply a co-rotation prevention check mark to the urea pump from the urea tank sub-assembly.

NOTICE:
·

The urea tank sub-assembly cutout is aligned with the protrusion on the urea tube with heater assembly.

·

If the urea pump and urea tank sub-assembly are not firmly attached and the urea pump gauge retainer is rotated, the urea pump will co-rotate and result in the urea pump being damaged.

·

Make sure to apply co-rotation prevention check mark to prevent the urea pump from co-rotating.




b.
A396440C02
1.188,0.885 1.542,0.552 1.542,0.552 1.677,0.552 true 0.667,0.75 0.917,0.75 true 1.917,2.396 2.073,2.146 2.073,2.146 2.167,2.146 true 1.083,2.854 1.25,2.854 1.25,2.854 1.583,2.625 true 1.073,2.135 1.24,2.135 1.24,2.135 1.573,2.469 true 0.458,3.813 0.792,3.813 true 1.719,0.479 1.958,0.635 0.24,0.156 10 false *1 0.479,0.667 0.719,0.813 0.24,0.146 10 false *a 0.896,2.771 1.135,2.927 0.24,0.156 10 false *b 0.896,2.063 1.135,2.229 0.24,0.167 10 false *c 0.271,3.74 0.521,3.917 0.25,0.177 10 false *d 2.188,2.073 2.427,2.229 0.24,0.156 10 false *1
*1 Urea Pump Gauge Retainer
*a SST (Claw Set)
*b Rib
*c Cutout
*d SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Urea Pump Gauge Retainer)


Set 4 SST (claw sets) to the urea pump gauge retainer and temporarily install.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)

NOTICE:
·

Align the cutout of SST (claw set) to the rib of the urea pump gauge retainer.

·

Do not place SST on the rotational start paint mark of the urea pump gauge retainer, otherwise SST (claw set) cannot be set correctly.




c.
A396441C02
0.479,1.99 0.646,1.99 0.646,1.99 1.146,1.823 true 1.375,1.031 0.708,1.031 true 2.104,1.365 2.438,0.865 2.438,0.865 2.604,0.865 true 2.646,0.781 2.958,0.938 0.313,0.156 10 false *1 0.521,0.938 0.833,1.094 0.313,0.156 10 false *a 0.281,1.896 0.594,2.052 0.313,0.156 10 false *b
*1 Urea Pump Gauge Retainer
*a SST (Claw Set)
*b Press
V100135

Pinch
V100136

SST (Bolt)


While firmly pressing the claw of SST into rib of the urea pump gauge retainer, tighten the bolt.


d.
A436309C01
2.333,0.417 2.667,0.25 2.667,0.25 2.833,0.25 true 2.146,1.448 2.865,1.448 true 2.865,0.156 3.177,0.313 0.313,0.156 10 false *a 2.896,1.354 3.135,1.51 0.24,0.156 10 true *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SST (bolts).


e.
A436310C01
1.708,1.104 0.677,0.823 0.677,0.823 0.479,0.823 true 2.021,1.396 2.875,1.396 true 0.292,0.729 0.604,0.885 0.313,0.156 10 false *a 2.906,1.313 3.219,1.469 0.313,0.156 10 false *b
*a Center of Urea Pump Gauge Retainer
*b SST (Plate)


Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the urea pump gauge retainer.


f.
A436311C01
1.042,0.198 2.292,0.198 true 1.25,0.521 2.25,0.771 2.25,0.771 2.417,0.771 true 1.656,2.979 1.99,3.24 1.99,3.24 2.156,3.24 true 1.875,2.333 2.458,2.333 true 1.177,2.604 1.01,2.438 1.01,2.438 0.844,2.438 true 0.667,2.333 0.979,2.49 0.313,0.156 10 false *1 2.333,0.104 2.646,0.26 0.313,0.156 10 false *a 2.49,2.25 2.802,2.406 0.313,0.156 10 false *b 2.458,0.688 2.771,0.844 0.313,0.156 10 false *c 2.198,3.146 2.51,3.302 0.313,0.156 10 false *d
*1 Urea Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
*d Rib
V113147

Press


While firmly pressing SST (claw set) into rib of the urea pump gauge retainer, tighten SST (bolt).


g.
A436312C01
2.635,0.385 2.854,0.385 true 1.083,0.583 1.5,0.333 1.5,0.333 1.667,0.333 true 0.646,1.438 1.313,1.438 true 0.479,1.344 0.792,1.5 0.313,0.156 10 false *a 1.698,0.24 2.01,0.396 0.313,0.156 10 false *b 2.865,0.281 3.073,0.448 0.208,0.167 10 true *c
*a SST (Plate)
*b SST (Handle)
*c SST (Claw Set)
V113147

Loosen


Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)


h.

Slowly loosen the urea pump gauge retainer by approximately 90°.

NOTICE:
·

Do not use any tools other than SST, such as screwdriver, etc.

·

Do not apply excessive force when pressing down on SST, as urea tube with heater assembly will place excessive force on the urea pump gauge retainer and be difficult to remove, and parts may be damaged.

·

Do not use an impact wrench or turn SST handle with excessive force, as parts may be damaged.




i.

While on person slowly loosens the urea pump gauge retainer, have another person press down the rising urea pump, securely attach the protrusion of the urea pump to the groove of the urea tank sub-assembly, and then remove the urea pump gauge retainer while making sure that the urea pump is properly aligned.

NOTICE:
·

If the urea pump gauge retainer is turned while the urea pump and urea tank sub-assembly are not correctly aligned, urea pump will move with the urea pump gauge retainer, and the urea pump and urea tank sub-assembly may both be damaged.

·

Do not rotate the urea pump gauge retainer when the co-rotation prevention check mark is out of place.



A436313C01
5.344,1.76 6.01,1.76 true 5.615,1.771 5.615,2.021 5.615,2.021 5.948,2.021 true 1,1.594 0.583,1.677 0.583,1.677 0.417,1.677 true 0.76,0.885 1.01,0.635 1.01,0.635 1.177,0.635 true 0.24,1.583 0.552,1.74 0.313,0.156 10 false *a 1.208,0.542 1.521,0.698 0.313,0.156 10 false *b 2.646,1.052 2.958,1.208 0.313,0.156 10 false *c 4.156,0.313 4.469,0.469 0.313,0.156 10 false *d 5.188,1.667 5.417,1.833 0.229,0.167 10 true *e 4.938,0.833 5.25,0.99 0.313,0.156 10 false *d 2.229,1.073 2.542,1.229 0.313,0.156 10 false *d 1.646,0.667 1.958,0.823 0.313,0.156 10 false *d 4.479,1.875 4.792,2.031 0.313,0.156 10 false *c 0.01,1.073 0.323,1.229 0.313,0.156 10 true *c 1.99,2.177 2.302,2.333 0.313,0.156 10 true *c
*a SST (Plate) *b SST (Handle)
*c Person in Charge of Loosening *d Person in Charge of Supporting
*e Co-rotation Prevention Check Mark - -



j.
A436314

Remove the urea pump from the urea tank sub-assembly.


k.
A436315

Remove the gasket from the urea tank sub-assembly.