Refer to DTC P054411.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P054411
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P05442A | Exhaust Gas Temperature Sensor 1 Bank 1 Signal Stuck In Range | The change in the exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small (2 trip detection logic). | ·
Exhaust gas temperature sensor ·
ECM (soak timer) |
Comes on | DTC stored | SAE Code: P2080 |
| P20312A | Exhaust Gas Temperature Sensor 2 Bank 1 Signal Stuck In Range | The change in the No. 2 exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small (2 trip detection logic). | ·
No. 2 exhaust gas temperature sensor ·
ECM (soak timer) |
Comes on | DTC stored | SAE Code: P2084 |
| P242A2A | Exhaust Gas Temperature Sensor 3 Bank 1 Signal Stuck In Range | The change in the No. 3 exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small (2 trip detection logic). | ·
No. 3 exhaust gas temperature sensor ·
ECM (soak timer) |
Comes on | DTC stored | SAE Code: P242B |
| DTC No. | Data List |
|---|---|
| P05442A
P20312A P242A2A |
·
Exhaust Temperature B1S1 ·
Exhaust Temperature B1S2 ·
Exhaust Temperature B1S3 |
Sensor 1 represents the sensor located upstream of the DOC catalytic converter.
Sensor 2 represents the sensor located upstream of the DPF catalytic converter.
Sensor 3 represents the sensor located downstream of the DPF catalytic converter.
If DTC P05442A, P20312A and/or P242A2A is stored, the following symptoms may appear:
White smoke
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P05442A | Check the exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving* |
| P20312A | Check the No. 2 exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving* |
| P242A2A | Check the No. 3 exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving* |
*: Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.
Refer to DTC P054411.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P054411
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P05442A, P20312A or P242A2A is output | A |
| DTC P05442A, P20312A or P242A2A and other DTCs are output | B |
A
B
Leave the vehicle as is for 1 to 2 hours with the engine stopped.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.
| Tester Display |
|---|
| Exhaust Temperature B1S1 |
| Exhaust Temperature B1S2 |
| Exhaust Temperature B1S3 |
Record the exhaust temperature displayed on the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.
Stop the vehicle.
Connect the GTS to the DLC3.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.
| Tester Display |
|---|
| Exhaust Temperature B1S1 |
| Exhaust Temperature B1S2 |
| Exhaust Temperature B1S3 |
Read the value.
| Result | Proceed to |
|---|---|
| Difference between Exhaust Temperature B1S1 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S1 checked after driving is within +/-15°C (27°F) | A |
| Difference between Exhaust Temperature B1S2 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S2 checked after driving is within +/-15°C (27°F) | |
| Difference between Exhaust Temperature B1S3 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S3 checked after driving is within +/-15°C (27°F) | |
| Difference between exhaust temperature recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and exhaust temperature checked after driving is equal to or greater than +/- 15°C (27°F) | B |
A
B
Replace the exhaust temperature sensor that changed a small amount in "INSPECT EXHAUST GAS TEMPERATURE SENSOR".
Replace the exhaust gas temperature sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
Replace the No. 2 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
Replace the No. 3 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Leave the vehicle as is for 1 to 2 hours with the engine stopped.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.
| Tester Display |
|---|
| Exhaust Temperature B1S1 |
| Exhaust Temperature B1S2 |
| Exhaust Temperature B1S3 |
Record the exhaust temperature displayed on the GTS.
Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.
Stop the vehicle.
Connect the GTS to the DLC3.
Enter the following menus: Powertrain / Engine / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.
| Tester Display |
|---|
| Exhaust Temperature B1S1 |
| Exhaust Temperature B1S2 |
| Exhaust Temperature B1S3 |
Check the exhaust temperature after leaving the vehicle for 1 to 2 hours and after driving.
+/-15°C (27°F) or more
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT