Refer to DTC P202A12.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P202A12
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P20B912 | Reductant Heater "A" Control Circuit High Circuit Short to Battery | When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more (1 trip detection logic). | ·
Open or short in urea tube with heater assembly circuit ·
Urea tube with heater assembly ·
Urea pump control ECU |
Comes on | DTC stored | SAE Code: P20BC |
| P20B914 | Reductant Heater "A" Control Circuit Low Circuit Short to Ground or Open | When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more (1 trip detection logic). | ·
Open or short in urea tube with heater assembly circuit ·
Urea tube with heater assembly ·
Urea pump control ECU |
Comes on | DTC stored | SAE Code: P20BB |
| DTC No. | Data List |
|---|---|
| P20B912
P20B914 |
Reductant Pipe Heater |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P20B912
P20B914 |
Reductant Pipe Heater (Active Test) |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the urea tube with heater assembly connector.
| *a | Component without harness connected
(to Urea Tube with Heater Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 6.39 to 7.81 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the urea tube with heater assembly connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| x3-2 (HTUL) - N37-20 (HTL) | Always | Below 1 Ω |
| x3-1 (GND) - N37-32 (EHTL) | Always | Below 1 Ω |
| x3-2 (HTUL) or N37-20 (HTL) - Body ground and other terminals | Always | 10 kΩ or higher |
| x3-1 (GND) or N37-32 (EHTL) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Reductant Pipe Heater.
| Tester Display |
|---|
| Reductant Pipe Heater |
Perform the Active Test.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P20B912 or P20B914 is output | A |
| DTCs is not output | B |
A
B
Replace the urea pump control ECU.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Reductant Pipe Heater.
| Tester Display |
|---|
| Reductant Pipe Heater |
Perform the Active Test.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the urea tube with heater assembly.
| Proceed to |
|---|
| NEXT |
NEXT