For more information on the differential pressure sensor and Diesel Particulate Filter (DPF), refer to the following procedures.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION
If P245211 and/or P245215 is present, refer to the DTC chart for DPF system.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION
The two sensing chambers of the differential pressure sensor are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration.
The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor. If the difference between the pressure before and after the DPF catalytic converter exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.
When the output voltage of the sensor deviates from the normal operating range, the ECM interprets this as a malfunction of the sensor circuit, and sets DTC P245211 or P245215, and illuminates the MIL.
If the vacuum hoses of the differential pressure sensor are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P24521C (Particulate Filter Pressure Sensor "A" Circuit Voltage Out of Range) is stored and the MIL illuminates.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P245211 | Particulate Filter Pressure Sensor "A" Circuit Short to Ground | Differential pressure sensor output voltage is below 0.4 V for 3 seconds or more (1 trip detection logic). | ·
Open or short in differential pressure sensor circuit ·
Differential pressure sensor ·
ECM |
Comes on | DTC stored | SAE Code: P2454 |
| P245215 | Particulate Filter Pressure Sensor "A" Circuit Short to Battery or Open | Differential pressure sensor output voltage is higher than 4.8 V for 3 seconds or more (1 trip detection logic). | ·
Open or short in differential pressure sensor circuit ·
Differential pressure sensor ·
ECM |
Comes on | DTC stored | SAE Code: P2455 |
| DTC No. | Data List |
|---|---|
| P245211
P245215 |
Particulate Filter Differential Pressure Bank 1 |
DTC P24521C (Particulate Filter Pressure Sensor "A" Circuit Voltage Out of Range) will be stored if there is incorrect vacuum hose routing to the differential pressure sensor.
After confirming DTC P245211 and P245215, check the differential pressure in the "Powertrain / Engine / Data List / Diesel Exhaust / Particulate Filter Differential Pressure Bank 1" menu using the GTS.
| Condition | Particulate Filter Differential Pressure Bank 1 Output | Sensor Condition |
|---|---|---|
| Ignition switch ON | Approximately 0 kPa | Normal |
| Always | -5 kPa or less or higher than 99 kPa | Open or short circuit |
| 4000 rpm (No engine load) | Negative output | Incorrect hose routing |
In order to detect abnormality in the differential pressure sensor, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range (between 0.4 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction in the sensor circuit and illuminates the MIL.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P245211
P245215 |
Ignition switch ON for 5 seconds |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Differential Pressure Sensor) |
Disconnect the differential pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E43-3 (VC) - E43-1 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E7-27 (PEX) - E7-26 (EPEX) | Ignition switch ON | 0.4 to 4.8 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds.
Turn the ignition switch to ON and wait for 3 seconds.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the differential pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E43-2 (PEX) - E7-27 (PEX) | Always | Below 1 Ω |
| E43-3 (VC) - E7-32 (VCPX) | Always | Below 1 Ω |
| E43-1 (E2) - E7-26 (EPEX) | Always | Below 1 Ω |
| E43-2 (PEX) or E7-27 (PEX) - Body ground and other terminals | Always | 10 kΩ or higher |
| E43-3 (VC) or E7-32 (VCPX) - Body ground and other terminals | Always | 10 kΩ or higher |
| E43-1 (E2) or E7-26 (EPEX) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Differential Pressure Sensor) |
Disconnect the differential pressure sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E43-3 (VC) - E43-2 (PEX) | Ignition switch off | No short or no open circuit |
| E43-2 (PEX) - E43-1 (E2) | Ignition switch off | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the differential pressure sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component with harness connected
(ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E7-32 (VCPX) - E7-26 (EPEX) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
NG
OK