Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P256212  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High Circuit Short to Battery  P256214  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.

The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

A348993E01
1.125,2.385 0.677,1.354 0.677,1.354 0.844,1.354 true 1.271,1.813 1.427,1.198 1.427,1.198 1.573,1.198 true 1.229,3.104 1.49,3.594 1.49,3.594 1.615,3.594 true 0.063,2.74 0.615,3.135 0.552,0.396 10 false Sensor Vane 0.313,3.906 2.604,4.427 2.292,0.521 10 false Nozzle Vane Position Sensor (Turbocharger Nozzle Vane Control Actuator) 1.625,1.135 2.281,1.354 0.656,0.219 10 false Magnet 1.854,1.469 2.344,1.656 0.49,0.188 10 false VNVC 2.844,3.552 3.354,3.75 0.51,0.198 10 false ECM 4.219,1.656 4.688,1.854 0.469,0.198 10 false 4.65 3.531,0.677 5.333,1.094 1.802,0.417 10 false Nozzle Vane Position Sensor Output Voltage (V) 1.906,2.25 2.396,2.438 0.49,0.188 10 false VTA1 1.896,3.021 2.385,3.208 0.49,0.188 10 false VNE2 2.75,1.583 3.24,1.771 0.49,0.188 10 false VNVC 2.75,2.375 3.24,2.563 0.49,0.188 10 false VNA 2.729,3.167 3.219,3.354 0.49,0.188 10 false VNE2 1.656,3.521 2.313,3.74 0.656,0.219 10 false Magnet 0.896,1.281 1.479,1.479 0.583,0.198 10 false Hall IC 4.229,2.823 4.698,3.021 0.469,0.198 10 false 0.35 6.042,3.354 6.74,3.615 0.698,0.26 10 false Open 4.917,3.354 5.531,3.594 0.615,0.24 10 false Closed 5.021,3.76 6.615,4 1.594,0.24 10 false Nozzle Vane Position

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P256212 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High Circuit Short to Battery VNA voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger nozzle vane control actuator)

·

Open or short in nozzle vane position sensor circuit

·

ECM


Comes on DTC stored SAE Code: P2565
P256214 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low Circuit Short to Ground or Open VNA voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger nozzle vane control actuator)

·

Open or short in nozzle vane position sensor circuit

·

ECM


Comes on DTC stored SAE Code: P2564

HINT:

If DTC P256212 and/or P256214 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

- Lack of power

- Vehicle surge or hesitation under light or medium load



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P256212
P256214
Ignition switch ON for 2 seconds or more

WIRING DIAGRAM

A348545E14
0.615,2.646 1.073,2.844 0.458,0.198 10 false E42 0.615,2.854 3.344,3.26 2.729,0.406 10 false Nozzle Vane Position Sensor (Turbocharger Nozzle Vane Control Actuator) 5.771,2.625 6.229,2.823 0.458,0.198 10 false E7 5.781,2.802 6.24,3 0.458,0.198 10 false ECM 5.458,1.833 5.917,2.031 0.458,0.198 10 false VNE2 5.448,1.375 5.906,1.573 0.458,0.198 10 false VNA 5.448,0.896 5.969,1.094 0.521,0.198 10 false VNVC 5.198,0.896 5.656,1.094 0.458,0.198 10 false 30 5.208,1.375 5.667,1.573 0.458,0.198 10 false 23 5.198,1.833 5.656,2.031 0.458,0.198 10 false 22 1.677,1.021 2.198,1.219 0.521,0.198 10 false VNVC 1.708,1.49 2.167,1.688 0.458,0.198 10 false VTA1 1.688,1.948 2.146,2.146 0.458,0.198 10 false VNE2 2.177,0.906 2.635,1.104 0.458,0.198 10 false 1 2.188,1.385 2.646,1.583 0.458,0.198 10 false 3 2.188,1.833 2.646,2.031 0.458,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NOZZLE VANE POSITION SENSOR)
a.
C129053C51
0.583,1 1.021,1.271 0.438,0.271 1.49,1.24 1.292,1.552 true 1.771,1.24 1.906,1.552 true 0.677,1.052 1,1.24 0.323,0.188 10 false E42 0.938,1.573 1.458,1.75 0.521,0.177 10 false VNVC 0.094,0.063 0.313,0.219 0.219,0.156 10 false *a 1.917,1.583 2.552,1.813 0.635,0.229 10 false VNE2
*a Front view of wire harness connector
(to Nozzle Vane Position Sensor)


Disconnect the nozzle vane position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E42-1 (VNVC) - E42-2 (VNE2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.INSPECT NOZZLE VANE POSITION SENSOR (VNA VOLTAGE)

NG

7.CHECK ECM (POWER SOURCE OF NOZZLE VANE POSITION SENSOR)
2.INSPECT NOZZLE VANE POSITION SENSOR (VNA VOLTAGE)
a.
A372026C69
1.219,0.854 1.635,1.104 0.417,0.25 1.927,2.375 1.49,1.646 true 1.063,2.344 1.448,1.635 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.344,0.896 1.802,1.094 0.458,0.198 10 false E7 0.75,2.427 1.427,2.646 0.677,0.219 10 false 23 (VNA) 1.698,2.448 2.438,2.667 0.74,0.219 10 false 22 (VNE2)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-23 (VNA) - E7-22 (VNE2) Ignition switch ON 2.3 to 2.7 V



Result:
Proceed to
OK
NG



OK

9.REPLACE ECM

NG

3.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)
3.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)
a.

Disconnect the nozzle vane position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E42-3 (VTA1) - E7-23 (VNA) Always Below 1 Ω
E42-2 (VNE2) - E7-22 (VNE2) Always Below 1 Ω
E42-3 (VTA1) or E7-23 (VNA) - Body ground and other terminals Always 10 kΩ or higher
E42-2 (VNE2) or E7-22 (VNE2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK ECM (CHECK RESISTANCE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the nozzle vane position sensor connector.


b.
C129053C52
0.583,1 1.021,1.271 0.438,0.271 1.49,1.24 1.24,1.74 true 1.719,1.26 1.74,1.698 true 2.01,1.271 2.313,1.75 true 0.677,1.052 1,1.24 0.323,0.188 10 false E42 0.833,1.75 1.354,1.927 0.521,0.177 10 false VNVC 0.094,0.063 0.313,0.219 0.219,0.156 10 false *a 1.583,1.74 2.219,1.969 0.635,0.229 10 false VNE2 2.219,1.76 2.854,1.99 0.635,0.229 10 false VTA1
*a Front view of wire harness connector
(to Nozzle Vane Position Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E42-1 (VNVC) - E42-3 (VTA1) Ignition switch off No short or no open circuit
E42-3 (VTA1) - E42-2 (VNE2) Ignition switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

5.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR

NG

9.REPLACE ECM
5.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
a.

Replace the turbocharger nozzle vane control actuator.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK ECM (POWER SOURCE OF NOZZLE VANE POSITION SENSOR)
a.
A372026C70
1.219,0.854 1.635,1.104 0.417,0.25 1.927,2.375 1.49,1.646 true 1.063,2.344 1.438,1.698 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.344,0.896 1.802,1.094 0.458,0.198 10 false E7 0.677,2.427 1.406,2.656 0.729,0.229 10 false 30 (VNVC) 1.729,2.438 2.427,2.656 0.698,0.219 10 false 22 (VNE2)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-30 (VNVC) - E7-22 (VNE2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

8.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

9.REPLACE ECM
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for 30 seconds or more.


d.

Turn the ignition switch to ON for 2 seconds or more.


e.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P256212 and/or P256214.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, idle the engine.



Result:
Proceed to
NEXT



NEXT

END