Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2020.06
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P261029  ECM/PCM Engine Off Timer Performance Signal Invalid  


DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A444446E01
5.073,0.885 7.063,1.083 1.99,0.198 10 false Soak Timer IC 4.5,2.063 6.49,2.26 1.99,0.198 10 false IGSW 5.229,2.542 6.823,2.792 1.594,0.25 10 false Power Source IC 5.115,4.021 6.708,4.271 1.594,0.25 10 false Main Relay Control IC 4.531,4.063 6.521,4.26 1.99,0.198 10 false MREL 4.49,2.458 6.479,2.656 1.99,0.198 10 false +B3 4.51,2.885 6.5,3.083 1.99,0.198 10 false +B2 4.521,3.281 6.51,3.479 1.99,0.198 10 false +B 3.042,4.51 5.031,4.708 1.99,0.198 10 false EFI MAIN 1,2.365 2.99,2.563 1.99,0.198 10 false IG2 MAIN 0.458,3.906 2.448,4.104 1.99,0.198 10 false FL MAIN 0.583,4.792 2.573,4.99 1.99,0.198 10 false Battery 1.021,3.552 3.01,3.75 1.99,0.198 10 false EFI-MAIN 3.719,2.354 5.708,2.552 1.99,0.198 10 false IG2 NO. 1 2.083,2.542 4.073,2.74 1.99,0.198 10 false IG2 MAIN 2.594,0.469 4.583,0.667 1.99,0.198 10 false IG2 1.833,0.469 3.823,0.667 1.99,0.198 10 false AM2 0.781,0.771 2.771,0.969 1.99,0.198 10 false AM2 5.75,4.99 7.156,5.385 1.406,0.396 10 false ECM 1.521,1.021 3.51,1.219 1.99,0.198 10 false Ignition Switch Assembly

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P261029 ECM/PCM Engine Off Timer Performance Signal Invalid ECM internal malfunction (2 trip detection logic). ECM Comes on DTC stored SAE Code: P2610

MONITOR DESCRIPTION

If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the ignition switch is turned to ON.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:
·

DTC P261029 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is necessary.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and wait for 10 minutes or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

If no pending DTC is output, the repair has been successfully completed.


Result:
Proceed to
NEXT



NEXT

END