When the speed limiter is turned on using the speed limiter switch, the ECM illuminates the speed limiter indicator and activates the speed limiter system. Each function of the speed limiter system can be activated by operating the steering switch. When the cruise control system is operating, the speed limiter system will not operate.
Turn the ignition switch to ON.
Turn the cruise control on using the cruise control main switch.
Check the operation of each function by operating the cruise control main switch.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>ROAD TEST
Each function of the cruise control system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / ASL SW.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ASL SW | Speed limiter switch signal | ON or OFF | OFF: Speed limiter switch off
ON: Speed limiter switch on |
- |
| Tester Display |
|---|
| ASL SW |
The Data List item ASL SW changes according to the operation of the switch.
| Proceed to |
|---|
| OK |
| NG |
OK
for 7GR-FKS: Click hereEngine / Hybrid System>7GR-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG
for 7GR-FKS:
Disconnect the N1 ECM connector.
Disconnect the N58 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N1-18 (ASLM) - N58-3 (ASL) | Always | Below 1 Ω |
| N1-18 (ASLM) or N58-3 (ASL) - Body ground | Always | 10 kΩ or higher |
| N58-2 (ECC) - Body ground | Always | Below 1 Ω |
for 1GD-FTV:
Disconnect the A2 ECM connector.
Disconnect the N58 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A2-27 (ASLM) - N58-3 (ASL) | Always | Below 1 Ω |
| A2-27 (ASLM) or N58-3 (ASL) - Body ground | Always | 10 kΩ or higher |
| N58-2 (ECC) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
for 7GR-FKS: Click hereEngine / Hybrid System>7GR-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG