Home › Drivetrain › RC60J (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION SYSTEM (for 7GR-FKS)
RM35X0E _52 Drivetrain _078740 RC60J MANUAL TRANSMISSION / TRANSAXLE _0383349 MANUAL TRANSMISSION SYSTEM(for 7GR-FKS) C

RC60J MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION SYSTEM(for 7GR-FKS)  P03352A  Crankshaft Position Sensor "A" Signal Stuck in Range  P033531  Crankshaft Position Sensor "A" No Signal  


DESCRIPTION

The crankshaft position sensor system consists of a No. 1 crankshaft position sensor plate and Magneto-Resistance Element (MRE) type sensor. The No. 1 crankshaft position sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the NE signal to detect the crankshaft position and engine speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P03352A Crankshaft Position Sensor "A" Signal Stuck in Range No crankshaft position sensor signal received by ECM while cranking for 4.7 seconds (1-trip detection logic).
·

SFI system

·

ECM


Does not come on DTC stored SAE Code:
P0335
P033531 Crankshaft Position Sensor "A" No Signal 3 seconds after engine starts, the engine stalls and the engine speed signal value decreases rapidly (1-trip detection logic).
·

SFI system

·

ECM


Does not come on DTC stored SAE Code:
P0335

HINT:

When the engine is being stopped or started automatically by stop and start system control, the ECM does not monitor the crankshaft position sensor signal.


MONITOR DESCRIPTION

A DTC will be stored if any of the following occur:

·

The crankshaft position sensor signal (NE signal) is not received by the ECM when the engine is being cranked.

·

The engine stalls and the engine speed signal value decreases rapidly (under normal conditions, the engine speed will decrease gradually).


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 30 seconds or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

8.

Input the DTC: P03352A or P033531.

9.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

Refer to SFI system DTC P033511.

Click hereEngine / Hybrid System>7GR-FKS (ENGINE CONTROL)>SFI SYSTEM>P033511

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the iMT system are replaced.

Click hereDrivetrain>RC60J (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSMISSION SYSTEM (for 7GR-FKS)>INITIALIZATION


HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



DATA LIST


HINT:

The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211
Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
550 to 700 rpm: Idling (shift lever in neutral, engine warmed up and A/C off) When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.


PROCEDURE

1.CHECK DTC OUTPUT (SFI SYSTEM)
a.

Check for SFI system DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B