Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › UREA PUMP
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384127 UREA PUMP A

1GD-FTV EMISSION CONTROL  UREA PUMP  INSTALLATION  


PROCEDURE

Hide 77871A 1.INSTALL UREA PUMP

a.

Install a new gasket to the urea tank sub-assembly.


b.
A436316C01
2.563,1.792 2.875,1.604 2.875,1.604 3.083,1.604 true 3.104,1.5 3.344,1.688 0.24,0.188 10 true *a
*a Matchmark


Install the urea pump to the urea tank sub-assembly as shown in the illustration.


c.
A436317C01
1.563,1.542 0.771,1.542 true 1.5,1.833 1.083,1.833 1.083,1.833 1.083,1.552 true 0.604,1.448 0.854,1.615 0.25,0.167 10 true *a
*a Co-rotation Prevention Check Mark


Apply a co-rotation prevention check mark to the urea pump and urea tank sub-assembly.

HINT:

Perform this procedure when replacement of the urea pump is necessary.



d.
A443368C01
2.375,0.917 2.656,0.521 2.656,0.521 2.823,0.521 true 2.677,0.885 2.792,1.135 2.792,1.135 2.958,1.135 true 2.854,0.427 3.083,0.583 0.229,0.156 10 true *a 2.979,1.052 3.208,1.219 0.229,0.167 10 true *b
*a Rotational Start Point Mark (Urea Pump Gauge Retainer Side)
*b Rotational Start Point Mark (Urea Tank Sub-assembly Side)


Temporarily place the urea pump gauge retainer by aligning the rotational start point mark of the urea pump gauge retainer with the rotational start point mark of the urea tank sub-assembly while pressing the urea pump into the urea tank assembly.


e.
A396440C02
1.188,0.885 1.542,0.552 1.542,0.552 1.677,0.552 true 0.667,0.75 0.917,0.75 true 1.917,2.396 2.073,2.146 2.073,2.146 2.167,2.146 true 1.083,2.854 1.25,2.854 1.25,2.854 1.583,2.625 true 1.073,2.135 1.24,2.135 1.24,2.135 1.573,2.469 true 0.458,3.813 0.792,3.813 true 1.719,0.479 1.958,0.635 0.24,0.156 10 false *1 0.479,0.667 0.719,0.813 0.24,0.146 10 false *a 0.896,2.771 1.135,2.927 0.24,0.156 10 false *b 0.896,2.063 1.135,2.229 0.24,0.167 10 false *c 0.271,3.74 0.521,3.917 0.25,0.177 10 false *d 2.188,2.073 2.427,2.229 0.24,0.156 10 false *1
*1 Urea Pump Gauge Retainer
*a SST (Claw Set)
*b Rib
*c Cutout
*d SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Urea pump Gauge Retainer)


Set 4 SST (claw sets) to the urea pump gauge retainer and temporarily install.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)


f.
A396441C02
0.479,1.99 0.646,1.99 0.646,1.99 1.146,1.823 true 1.375,1.031 0.708,1.031 true 2.104,1.365 2.438,0.865 2.438,0.865 2.604,0.865 true 2.646,0.781 2.958,0.938 0.313,0.156 10 false *1 0.521,0.938 0.833,1.094 0.313,0.156 10 false *a 0.281,1.896 0.594,2.052 0.313,0.156 10 false *b
*1 Urea Pump Gauge Retainer
*a SST (Claw Set)
*b Press
V100135

Pinch
V100136

SST (Bolt)


While firmly pressing the claw of SST into rib of the urea pump gauge retainer, tighten the bolt.


g.
A443366C01
2.24,0.385 2.594,0.188 2.594,0.188 2.76,0.188 true 2.125,0.51 2.677,0.656 2.677,0.656 2.844,0.656 true 2.792,0.094 3.104,0.25 0.313,0.156 10 false *a 2.875,0.573 3.188,0.729 0.313,0.156 10 false *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SST (bolts).


h.
A443367C01
0.469,0.604 0.667,0.604 0.667,0.604 1.698,1.094 true 2.354,1.656 2.875,1.656 true 0.281,0.51 0.594,0.667 0.313,0.156 10 false *a 2.875,1.552 3.115,1.76 0.24,0.208 10 true *b
*a Center of Urea Pump Gauge Retainer
*b SST (Plate)


Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the urea pump gauge retainer.


i.
A436311C01
1.042,0.198 2.292,0.198 true 1.25,0.521 2.25,0.771 2.25,0.771 2.417,0.771 true 1.656,2.979 1.99,3.24 1.99,3.24 2.156,3.24 true 1.875,2.333 2.458,2.333 true 1.177,2.604 1.01,2.438 1.01,2.438 0.844,2.438 true 0.667,2.333 0.979,2.49 0.313,0.156 10 false *1 2.333,0.104 2.646,0.26 0.313,0.156 10 false *a 2.49,2.25 2.802,2.406 0.313,0.156 10 false *b 2.458,0.688 2.771,0.844 0.313,0.156 10 false *c 2.198,3.146 2.51,3.302 0.313,0.156 10 false *d
*1 Urea Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
*d Rib
V113147

Press


While firmly pressing SST (claw set) into rib of the urea pump gauge retainer, tighten SST (bolt).


j.
A436318C01
2.375,0.906 2.646,0.604 2.646,0.604 2.865,0.604 true 1.552,1.552 0.74,1.552 true 1.5,1.823 1.042,1.823 1.042,1.823 1.042,1.563 true 2.885,0.51 3.156,0.708 0.271,0.198 10 false *a 0.531,1.458 0.729,1.615 0.198,0.156 10 true *b
*a Tighten Start Position
*b Co-rotation Prevention Check Mark


While one person presses the urea pump into the urea tank sub-assembly, have another person firmly press the urea pump gauge retainer into the threads of the urea tank assembly and tighten approximately one and a half turns.

NOTICE:
·

Do not any tools other than SST, such as a screwdriver, etc.

·

Do not apply excessive force when pressing down on SST, as the urea pump will place excessive force on urea pump gauge retainer and be difficult to remove, and parts may be damaged.

·

Do not use an impact wrench or turn SST handle with excessive force, as parts may be damaged.

·

Do not rotate the urea pump gauge retainer when the co-rotation prevention check mark is out of place.




k.
A436319C01
1.708,0.792 1.333,0.167 1.333,0.167 1.125,0.167 true 0.948,0.073 1.26,0.229 0.313,0.156 10 false *a 0.219,0.75 0.531,0.906 0.313,0.156 10 false *b 2.125,0.021 2.354,0.177 0.229,0.156 10 true *c 2.49,1.719 2.802,1.875 0.313,0.156 10 false *b 2.948,0.521 3.177,0.677 0.229,0.156 10 true *c
*a SST (Plate)
*b Person in Change of Tightening
*c Person in Charge of Supporting


While one person presses the urea pump into the urea tank sub-assembly, have another person slowly tighten approximately half turns.


l.
A436320C01
0.49,1.531 0.74,1.531 0.74,1.531 1.375,1.281 false 1.083,0.792 1.333,0.458 1.333,0.458 1.5,0.458 true 1.781,2.969 1.24,2.646 1.24,2.646 1.073,2.646 true 0.313,1.427 0.625,1.583 0.313,0.156 10 false *a 1.531,0.365 1.844,0.521 0.313,0.156 10 false *b 0.844,2.885 1.094,3.052 0.25,0.167 10 true *c 0.833,2.563 1.063,2.729 0.229,0.167 10 true *d 0.417,0.51 0.729,0.667 0.313,0.156 10 false *e 2.125,0.542 2.438,0.698 0.313,0.156 10 false *f 2.833,1.75 3.146,1.906 0.313,0.156 10 false *e 2.833,1.031 3.146,1.188 0.313,0.156 10 false *f
*a SST (Plate)
*b SST (Handle)
*c Tightening Complete Position
*d Rotational Start Point Mark of Urea Pump Gauge Retainer
*e Person in Charge of Tightening
*f Person in Charge of Supporting
V113147

Tighten


Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)


m.

While one person presses the urea pump onto the urea tank sub-assembly, have another person use SST (handle) and slowly tighten the urea pump gauge retainer until it reaches the tightening complete position.


Hide 77801A 2.INSTALL UREA TANK SUB-ASSEMBLY