Home › Drivetrain › CLUTCH › CLUTCH ACCUMULATOR (for 7GR-FKS)
RM35X0E _52 Drivetrain _078837 CLUTCH _0382383 CLUTCH ACCUMULATOR(for 7GR-FKS) A

CLUTCH  CLUTCH ACCUMULATOR(for 7GR-FKS)  INSTALLATION  


PROCEDURE

Hide 31490 1.INSTALL CLUTCH ACCUMULATOR ASSEMBLY

a.

Install the clutch accumulator assembly with the 3 bolts.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


b.
C413016C01
1.49,0.531 1.802,0.729 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the clutch release cylinder to flexible hose tube to the clutch accumulator assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 31482D 2.INSTALL CLUTCH RELEASE CYLINDER TO ACCUMULATOR TUBE

a.
C414171C01
1.688,0.406 2,0.604 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, install the clutch release cylinder to accumulator tube to the clutch release cylinder assembly and clutch accumulator assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 31349 3.INSTALL CLUTCH CABLE HEAT INSULATOR

a.
C410613

Install the clutch cable heat insulator to the manual transmission assembly with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 4.INSTALL CLUTCH ACCUMULATOR HEAT INSULATOR

a.
C410612

Install the clutch accumulator heat insulator to the manual transmission assembly with the 4 bolts.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 5.BLEED AIR FROM CLUTCH PIPE LINE

Hide 6.CHECK FOR CLUTCH FLUID LEAKAGE

HINT:

Check for leaks in the clutch system.


Hide 7.CHECK FLUID LEVEL IN RESERVOIR

Hide 51773E 8.INSTALL STEP PLATE COVER RH (w/ Cover)

Hide 51407A 9.INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 3 Engine Under Cover Sub-assembly)

Hide 51405A 10.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 52618 11.INSTALL LOWER FRONT BUMPER ABSORBER

Hide 51406A 12.INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)