When the window defogger switch on the center cluster module control assembly (window defogger switch) is pressed, the operation signal is transmitted to the air conditioning amplifier assembly via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on the defogger relay (DEF) to operate the window defogger system.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check the air conditioning system.
Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.
The air conditioning system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the indicator light illuminates when the window defogger switch is on.
Indicator light illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the Active Test.
Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Defogger Relay (Rear) | Defogger relay (DEF) | OFF or ON | - |
| Tester Display |
|---|
| Defogger Relay (Rear) |
Back door glass (defogger wire) warms up.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air conditioning amplifier assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
Check that the window defogger system operates normally.
The window defogger system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Back Door Glass [Defogger Wire]) |
Disconnect the back door glass (defogger wire) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| k3-1 (B) - Body ground | Ignition switch ON, window defogger switch on | 11 to 14 V |
| Ignition switch ON, window defogger switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Back Door Glass [Defogger Wire]) |
Disconnect the back door glass (defogger wire) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| j1-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the defogger relay (DEF) from the No. 1 engine room relay block.
Inspect the defogger relay (DEF).
Click hereVehicle Exterior>WINDOW / GLASS>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Defogger Relay [DEF]) |
Remove the defogger relay (DEF) from the No. 1 engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Defogger relay (DEF) terminal 1 - Body ground | Ignition switch ON | 11 to 14 V |
| Defogger relay (DEF) terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the defogger relay (DEF) from the No. 1 engine room relay block.
Disconnect the N43 air conditioning amplifier assembly connector.
Disconnect the k3 back door glass (defogger wire) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Defogger relay (DEF) terminal 2 - N43-18 (RDEF) | Always | Below 1 Ω |
| Defogger relay (DEF) terminal 3 - k3-1 (B) | Always | Below 1 Ω |
| Defogger relay (DEF) terminal 2 or N42-18 (RDEF) - Body ground | Always | 10 kΩ or higher |
| Defogger relay (DEF) terminal 3 or k3-1 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG