87114B
1.INSTALL HEATER COVER (w/o PTC Heater)
|
Install in this Direction |
Install the heater cover with the screw.
87710G
2.INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)
|
Install in this Direction |
Install the quick heater assembly with the screw.
| *a | Element |
| *b | Fin |
Do not hold the quick heater assembly by the element or fin. Also, do not damage the quick heater assembly.
Foul odors may occur due to oil adhering to the quick heater assembly.
88625
3.INSTALL NO. 1 COOLER THERMISTOR (FRONT EVAPORATOR TEMPERATURE SENSOR)
88501
4.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
Install the No. 1 cooler evaporator sub-assembly together with the No. 1 cooler thermistor to the upper heater case.
Connect the connector clamp to the upper heater case.
Attach the guide to temporarily install the upper heater case to the lower heater case.
Attach the claw to install the upper heater case to the lower heater case.
Install the 2 screws.
87212
5.INSTALL REAR NO. 1 AIR DUCT (w/ Center Foot Duct)
Attach the guide and claw to install the rear No. 1 air duct.
87211X
6.INSTALL BLOWER COVER (w/o Center Foot Duct, w/o Rear Foot Duct)
Attach the guide and claw to install the blower cover.
88515
7.INSTALL COOLER EXPANSION VALVE
Remove the vinyl tape from the No. 1 cooler evaporator sub-assembly and cooler expansion valve.
Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the No. 1 cooler evaporator sub-assembly.
ND-OIL 8 or equivalent
Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 bolts.
Make sure not to cut the O-ring while installing it (Cut O-rings cannot be installed).
88899L
8.INSTALL COOLING UNIT PARTS
Install the cooling unit parts.
87107A
9.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
|
Install in this Direction |
Install the heater radiator unit sub-assembly shown in the illustration.
87124B
10.INSTALL HEATER CLAMP
Attach the claw to install the heater clamp.
88897M
11.INSTALL HEATER PIPE GROMMET
Install the heater pipe grommet as shown in the illustration.
Install the heater pipe grommet with the arrow facing up.
12.INSTALL NO. 2 HEATER CONTROL CABLE SUB-ASSEMBLY (except Automatic Air Conditioning System)
| *a | FACE |
Set the cable gear and unit link to the FACE position.
Attach the claw to install the No. 2 heater control cable sub-assembly.
13.INSTALL AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY (except Automatic Air Conditioning System)
| *a | MAX COOL |
Set the cable gear and unit gear to the MAX COOL position.
Attach the guide and claw to install the air mix damper control cable sub-assembly.
Attach the guide to install each cable.
87050C
14.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)
Align each gear on the air conditioner radiator assembly side as shown in the illustration, and then check that the gears of the No. 1 air conditioning radiator damper servo sub-assembly are aligned as shown in the illustration.
| *a | Gear Alignment Part | - | - |
Install the No. 1 air conditioning radiator damper servo sub-assembly with the 3 screws.
82210K
15.INSTALL AIR CONDITIONING HARNESS ASSEMBLY (for Automatic Air Conditioning System)
Attach the guide to install the air conditioning harness assembly.
Connect the 3 connectors.
88897P
16.INSTALL ASPIRATOR (for Automatic Air Conditioning System)
Attach the claw to install the aspirator.
87130D
17.INSTALL BLOWER ASSEMBLY
87211A
18.INSTALL NO. 2 AIR DUCT
Attach the claw to install the No. 2 air duct.
When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.
If the No. 2 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace with a new one.
88649
19.INSTALL NO. 2 COOLER WIRING (w/ PTC Heater)
|
Screw |
|
Connector |
Attach the claw and guide to install the No. 2 cooler wiring.
Install the 2 screws.
Connect the 2 connectors.
5538E
20.INSTALL ELECTRICAL PARTS MOUNTING BRACKET
Attach the guide and install the electrical parts mounting bracket with the screw.
55990B
21.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY
Attach the claw to install the lower defroster nozzle assembly.