Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT (for RHD) › 2019.02–2019.06
RM35X0E _58 Vehicle Interior _079316 HEATING / AIR CONDITIONING _0384875 FRONT AIR CONDITIONING UNIT(for RHD) A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT(for RHD)  REASSEMBLY  


PROCEDURE

Hide 87114B 1.INSTALL HEATER COVER (w/o PTC Heater)

a.
E415208C01
0,0 0,0 false
V113147

Install in this Direction


Install the heater cover with the screw.


Hide 87710G 2.INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)

a.
E415207C01
0,0 0,0 false
V113147

Install in this Direction


Install the quick heater assembly with the screw.

NOTICE:
E382588C01
0.677,1.646 0.677,1 true 0.188,1.646 0.188,0.896 0.188,0.896 0.5,0.896 true 0.604,1.667 0.917,1.865 0.313,0.198 10 false *a 0.115,1.667 0.427,1.865 0.313,0.198 10 false *b
*a Element
*b Fin


·

Do not hold the quick heater assembly by the element or fin. Also, do not damage the quick heater assembly.

·

Foul odors may occur due to oil adhering to the quick heater assembly.




Hide 88625 3.INSTALL NO. 1 COOLER THERMISTOR (FRONT EVAPORATOR TEMPERATURE SENSOR)

Hide 88501 4.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

a.
E415203

Install the No. 1 cooler evaporator sub-assembly together with the No. 1 cooler thermistor to the upper heater case.


b.

Connect the connector clamp to the upper heater case.


c.

Attach the guide to temporarily install the upper heater case to the lower heater case.

E415202


d.

Attach the claw to install the upper heater case to the lower heater case.


e.

Install the 2 screws.


Hide 87212 5.INSTALL REAR NO. 1 AIR DUCT (w/ Rear Foot Duct, w/ Center Foot Duct)

a.
E416455C01
0.156,0.198 0.458,0.417 0.302,0.219 12 false *A 0.156,1.896 0.385,2.094 0.229,0.198 12 false *B
*A w/ Rear Foot Duct
*B w/ Center Foot Duct


Attach the guide and claw to install the rear No. 1 air duct.


Hide 87211X 6.INSTALL BLOWER COVER (w/o Center Foot Duct, w/o Rear Foot Duct)

a.
E417492

Attach the guide and claw to install the blower cover.


Hide 88515 7.INSTALL COOLER EXPANSION VALVE

a.

Remove the vinyl tape from the No. 1 cooler evaporator sub-assembly and cooler expansion valve.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the No. 1 cooler evaporator sub-assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.
E415201

Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)

NOTICE:

Make sure not to cut the O-ring while installing it (Cut O-rings cannot be installed).



Hide 88899L 8.INSTALL COOLING UNIT PARTS

a.
E415200

Install the cooling unit parts.


Hide 87107A 9.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

a.
E415204C01
0,0 0,0 false
V113147

Install in this Direction


Install the heater radiator unit sub-assembly shown in the illustration.


Hide 87124B 10.INSTALL HEATER CLAMP

a.
E415198

Attach the claw to install the heater clamp.


Hide 88897M 11.INSTALL HEATER PIPE GROMMET

a.
E416460

Install the heater pipe grommet as shown in the illustration.

NOTICE:

Install the heater pipe grommet with the arrow facing up.



Hide 12.INSTALL NO. 2 HEATER CONTROL CABLE SUB-ASSEMBLY

a.
E416487C01
1.219,0.115 1.531,0.271 0.313,0.156 10 false *a 1.167,1.375 1.479,1.531 0.313,0.156 10 false *a
*a FACE


Set the cable gear and unit link to the FACE position.


b.
E415195

Attach the claw to install the No. 2 heater control cable sub-assembly.


Hide 13.INSTALL AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY

a.
E416485C01
2.052,0.115 2.271,0.281 0.219,0.167 10 true *a 1.917,1.958 2.135,2.125 0.219,0.167 10 true *a
*a MAX COOL


Set the cable gear and unit gear to the MAX COOL position.


b.
E415194

Attach the guide and claw to install the air mix damper control cable sub-assembly.


c.
E415193

Attach the guide to install each cable.


Hide 87130D 14.INSTALL BLOWER ASSEMBLY

Hide 87211A 15.INSTALL NO. 2 AIR DUCT

a.
E415187

Attach the claw to install the No. 2 air duct.

NOTICE:
·

When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.

·

If the No. 2 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace with a new one.




Hide 88649 16.INSTALL NO. 2 COOLER WIRING (w/ PTC Heater)

a.
E415186C01
0,0 0,0 false
V100135

Screw
V100136

Connector


Attach the guide to install the No. 2 cooler wiring.


b.

Install the 2 screws.


c.

Connect the 2 connectors.


Hide 5538E 17.INSTALL ELECTRICAL PARTS MOUNTING BRACKET

a.
E416457

Attach the guide and install the electrical parts mounting bracket with the screw.


Hide 55990B 18.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY

E415185

a.

Attach the claw to install the lower defroster nozzle assembly.