The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the horn button assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
45186
3.REMOVE LOWER NO. 2 STEERING WHEEL COVER
|
Protective Tape |
Using a screwdriver, insert the screwdriver into the cutout of the lower No. 2 steering wheel cover and detach the claw and guide to remove the lower No. 2 steering wheel cover.
Before performing work, wrap the tip of the screwdriver with protective tape and apply protective tape to the position shown in the illustration.
45187
4.REMOVE LOWER NO. 3 STEERING WHEEL COVER
|
Protective Tape |
Using a screwdriver, insert the screwdriver into the cutout of the lower No. 3 steering wheel cover and detach the claw and guide to remove the lower No. 3 steering wheel cover.
Before performing work, wrap the tip of the screwdriver with protective tape and apply protective tape to the position shown in the illustration.
45130
5.REMOVE HORN BUTTON ASSEMBLY
|
Deployment Side |
When storing the horn button assembly, keep the airbag deployment side facing upward.
If the airbag deploys for any reason, it may cause a serious accident.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
|
Release in this Direction |
Using a screwdriver, insert it from the hole of the steering wheel assembly and push the torsion spring to detach the pin.
Insert the screwdriver into the installation areas of the lower No. 2 steering wheel cover and lower No. 3 steering wheel cover.
| *a | Wire Harness Clamp |
|
Airbag Connector |
|
Horn Connector |
for Dual Type:
Tilt the horn button assembly toward the seat and support it with one hand.
Do not drop the horn button assembly.
When disconnecting the horn button assembly, do not pull the airbag wire harness.
Disconnect the 2 airbag connectors.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
Detach the wire harness clamp and disconnect the horn connector.
| *a | Wire Harness Clamp |
|
Airbag Connector |
|
Horn Connector |
for Single Type:
Tilt the horn button assembly toward the seat and support it with one hand.
Do not drop the horn button assembly.
When disconnecting the horn button assembly, do not pull the airbag wire harness.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR
Detach the wire harness clamp and disconnect the horn connector.