Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ VSC OFF Switch) › 2019.02–2019.06
RM35X0E _54 Brake _078667 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0385049 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/ VSC OFF Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/ VSC OFF Switch)  C13807F  Stop Lamp Relay Actuator Stuck Off  


DESCRIPTION

Refer to DTC C13807E.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ VSC OFF Switch)>C13807E

DTC No. Detection Item DTC Detection Condition Trouble Area
C13807F Stop Lamp Relay Actuator Stuck Off When the voltage at the +BS terminal is between 10 V or more and the STOP LP relay (stop light relay) drive output (STPO) is on, a signal is not input to the STP2 terminal for 5 seconds or more.
·

Wire harness or connector

·

STOP LP relay (stop light relay)

·

Skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ VSC OFF Switch)>UTILITY



HINT:

When DTC P057111, P057112 and/or P057113 are output together with DTC C13807F, inspect and repair the trouble areas indicated by DTC P057111, P057112 and/or P057113 first.

P057111: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ VSC OFF Switch)>P057111

P057112: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ VSC OFF Switch)>P057112

P057113: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ VSC OFF Switch)>P057113


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)

NG

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)
2.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / Brake / Active Test.

Chassis > Brake > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
Stop Lamp Relay STOP LP relay (stop light relay) OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this actuator and solenoid, this test will only last 5 seconds.


-
Chassis > Brake > Active Test
Tester Display
Stop Lamp Relay
50004 435 27

d.

According to the display on the GTS, perform the Active Test and check the operation of the stop lights.

OK:

Stop lights turn on in accordance with the Active Test.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A28 skid control ECU (brake actuator assembly) connector.


c.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - A28-24 (STP2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A28 skid control ECU (brake actuator assembly) connector.


c.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - A28-3 (STPO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (RELAY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RELAY POWER SOURCE CIRCUIT)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT STOP LIGHT RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT STOP LIGHT RELAY
a.

Turn the ignition switch off.


b.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


c.

Inspect the STOP LP relay (stop light relay).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>RELAY>ON-VEHICLE INSPECTION

OK:

The STOP LP relay (stop light relay) is normal.


Result:
Result
OK
NG




OK

NG

REPLACE STOP LIGHT RELAY

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT RELAY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A28 skid control ECU (brake actuator assembly) connector.


c.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - A28-24 (STP2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT RELAY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the M1 stop light switch assembly connector.


c.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M1-1 (L) - 4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT STOP LIGHT RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT STOP LIGHT RELAY
a.

Turn the ignition switch off.


b.

Remove the STOP LP relay (stop light relay) from the No. 1 engine room relay block and No. 1 junction block.


c.

Inspect the STOP LP relay (stop light relay).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>RELAY>ON-VEHICLE INSPECTION

OK:

The STOP LP relay (stop light relay) is normal.


Result:
Result
OK
NG




OK

NG

REPLACE STOP LIGHT RELAY