Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM35X0E _59 Vehicle Exterior _079320 WIPER / WASHER _0385301 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rear Wiper Motor Circuit  


DESCRIPTION

This circuit is the power source circuit for the rear wiper motor assembly.

WIRING DIAGRAM

E415848E01
0.823,3.854 1.135,4.052 0.313,0.198 10 false k2 0.823,4.021 2.615,4.25 1.792,0.229 10 false Rear Wiper Motor Assembly 3.177,0.875 3.49,1.073 0.313,0.198 10 false +1 3.49,0.875 3.646,1.073 0.156,0.198 10 false 1 4.74,0.865 4.896,1.063 0.156,0.198 10 false 1 4.948,0.875 5.563,1.073 0.615,0.198 10 false RMRY 5.115,1.875 5.573,2.073 0.458,0.198 10 false N18 5.125,2.042 6.771,2.417 1.646,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 6.542,1.073 6.938,1.302 0.396,0.229 10 false CPU 3.25,2.875 3.563,3.073 0.313,0.198 10 false B 3.49,2.875 3.646,3.073 0.156,0.198 10 false 4 3.99,3.177 4.76,3.375 0.771,0.198 10 false WIPER RR 5.708,2.979 7.063,3.208 1.354,0.229 10 false from IG1 NO.4 Relay 3.229,1.688 3.385,1.885 0.156,0.198 10 false E 3.5,1.688 3.656,1.885 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuse of circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (REAR WIPER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Wiper Operation Function to operate the rear wiper motor assembly OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Rear Wiper Operation
50004 123 90
OK:

Rear wiper motor assembly operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT REAR WIPER MOTOR ASSEMBLY
2.INSPECT REAR WIPER MOTOR ASSEMBLY
a.

Remove the rear wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>REMOVAL


b.

Inspect the rear wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE REAR WIPER MOTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
E415569C01
1.542,0.146 1.938,0.406 0.396,0.26 1.958,1.573 2.323,1.229 2.323,1.229 2.583,1.229 true 1.573,1.604 1.208,1.969 1.208,1.969 0.927,1.969 true 1.646,0.188 1.958,0.385 0.313,0.198 10 false k2 2.677,1.135 2.99,1.333 0.313,0.198 10 false B 0.729,1.865 0.885,2.063 0.156,0.198 10 false E 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Front Rear Wiper Motor Assembly)


Disconnect the rear wiper motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
k2-3 (E) - Body Ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
k2-4 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the k2 rear wiper motor assembly connector.


b.

Disconnect the N18 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
k2-1 (+1) - N18-1 (RMRY) Always Below 1 Ω
k2-1 (+1) or N18-1 (RMRY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR