Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL
RM35X0E _51 Engine / Hybrid System _079219 1GD-FTV ENGINE MECHANICAL _0385635 FRONT CRANKSHAFT OIL SEAL A

1GD-FTV ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11303A 1.INSTALL FRONT CRANKSHAFT OIL SEAL

a.

Apply MP grease to the lip of a new front crankshaft oil seal.

NOTICE:
·

Keep the lip free of foreign matter.

·

Do not allow MP grease to contact the dust seal.




b.
A343929C01
1.042,2.323 0.625,2.073 0.625,2.073 0.458,2.073 true 0.594,0.302 0.333,0.302 true 1.281,0.771 0.938,0.771 true 0.156,0.188 0.354,0.375 0.198,0.188 10 true *1 1.302,0.667 1.531,0.823 0.229,0.156 10 true *2 0.635,1.104 0.885,1.271 0.25,0.167 10 true *a 0.156,1.979 0.531,2.177 0.375,0.198 10 false SST
*1 Front Crankshaft Oil Seal
*2 Timing Chain Cover Assembly
*a 0 to 1.5 mm (0 to 0.0591 in.)


Using SST and a hammer, tap in the front crankshaft oil seal.

SST
09214-76011  

NOTICE:
·

The acceptable depth from the top of the timing chain cover assembly is 0 to 1.5 mm (0 to 0.0591 in.)

·

Keep the lip free from foreign matter.

·

Do not tap the front crankshaft oil seal at an angle.

·

Make sure that the front crankshaft oil seal is properly installed.




Hide 13471 2.INSTALL CRANKSHAFT PULLEY (for Automatic Transmission)

a.

Align the keyway of the crankshaft pulley with the key located on the crankshaft, and then slide the crankshaft pulley into place to install it.


b.
A343926N01
1.167,1 0.583,1.333 0.583,1.333 0.417,1.333 true 1.979,0.802 2.896,0.802 true 0.125,1.24 0.5,1.438 0.375,0.198 10 false SST 2.958,0.729 3.333,0.927 0.375,0.198 10 false SST

Using SST, install a new crankshaft pulley set bolt.

SST
09213-58014  (91551-80840)
09330-00021  

Torque:
365 N*m (3722 kgf*cm, 269 ft.*lbf)


Hide 13407 3.INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY (for Manual Transmission)

a.

Align the keyway of the crankshaft damper sub-assembly with the key located on the crankshaft, and then slide the crankshaft damper sub-assembly into place to install it.


b.
A444768N01
1.167,1 0.583,1.333 0.583,1.333 0.417,1.333 true 1.979,0.802 2.896,0.802 true 0.125,1.24 0.5,1.438 0.375,0.198 10 false SST 2.927,0.708 3.302,0.906 0.375,0.198 10 true SST

Using SST, install a new crankshaft pulley set bolt.

SST
09213-58014  (91551-80840)
09330-00021  

Torque:
365 N*m (3722 kgf*cm, 269 ft.*lbf)


Hide 13496 4.INSTALL CRANKSHAFT PULLY COVER (for Automatic Transmission)

a.

w/o Viscous Heater:

Install the crankshaft pulley cover to the crankshaft pulley with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

w/ Viscous Heater:

Install the crankshaft pulley cover to the crankshaft pulley.


Hide 88451B 5.INSTALL VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

a.

w/ Viscous Heater:

Install the crankshaft pulley cover to the crankshaft pulley.


b.

Install the viscous heater crankshaft pulley to the crankshaft pulley with the 4 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 16400 6.INSTALL RADIATOR ASSEMBLY