Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2019.02–2019.06
RM35X0E _56 Audio / Visual / Telematics _079315 PARK ASSIST / MONITORING _0385738 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB0  Short to +B in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a short to +B in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB0 Short to +B in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time


·

Outer mirror LH (outer rear view mirror indicator LH)

·

Outer mirror retractor LH

·

Harness or connector

·

Blind spot monitor sensor LH



WIRING DIAGRAM

E410127E01
2.552,1.469 2.708,1.667 0.156,0.198 10 false 2 2.521,1.875 2.792,2.083 0.271,0.208 10 false 1 2.344,1.594 2.5,1.792 0.156,0.198 10 false + 2.365,2.042 2.521,2.24 0.156,0.198 10 false - 0.573,2.406 1.229,2.635 0.656,0.229 10 false IND1 0.573,2.563 2.271,3.021 1.698,0.458 10 false Outer Mirror LH (Outer Rear View Mirror Indicator LH) 0.479,3.74 2.958,4.031 2.479,0.292 10 false Outer Rear View Mirror Assembly LH 6.01,1.594 6.479,1.792 0.469,0.198 10 false OMIL 5.75,1.469 6.219,1.667 0.469,0.198 10 false 4 5.844,3.552 6.313,3.75 0.469,0.198 10 false e2 5.844,3.729 7.052,4.344 1.208,0.615 10 false Blind Spot Monitor Sensor LH 0.458,3.552 0.875,3.74 0.417,0.188 10 false R20 3.844,1.49 4.24,1.656 0.396,0.167 10 false BSL+ 4.042,1.885 4.302,2.073 0.26,0.188 10 false E 4.313,1.438 4.604,1.604 0.292,0.167 10 false 1 4.344,1.854 4.635,2.021 0.292,0.167 10 false 11 2.635,2.49 4.375,2.792 1.74,0.302 10 false Outer Mirror Retractor LH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.
E406932C16
1.5,0.25 1.906,0.552 0.406,0.302 1.875,1.146 2.385,0.51 2.385,0.51 2.583,0.51 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.563,0.323 1.875,0.521 0.313,0.198 10 false e2 2.667,0.427 3.073,0.615 0.406,0.188 10 false OMIL
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Disconnect the blind spot monitor sensor LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
e2-4 (OMIL) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.
E406932C16
1.5,0.25 1.906,0.552 0.406,0.302 1.875,1.146 2.385,0.51 2.385,0.51 2.583,0.51 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.563,0.323 1.875,0.521 0.313,0.198 10 false e2 2.667,0.427 3.073,0.615 0.406,0.188 10 false OMIL
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Disconnect the blind spot monitor sensor LH connector.


b.

Disconnect the IND1 outer mirror LH (outer rear view mirror indicator LH) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
e2-4 (OMIL) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

NG

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.
E406932C16
1.5,0.25 1.906,0.552 0.406,0.302 1.875,1.146 2.385,0.51 2.385,0.51 2.583,0.51 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.563,0.323 1.875,0.521 0.313,0.198 10 false e2 2.667,0.427 3.073,0.615 0.406,0.188 10 false OMIL
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Disconnect the blind spot monitor sensor LH connector.


b.

Disconnect the R20 outer rear view mirror assembly LH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
e2-4 (OMIL) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR RETRACTOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR